Electrolux EDW7505HSS - Semi-Integrated Dishwasher With 5 Wash Cycles Installation Instructions page 2

,
7.
,
,
If levelers need to be removed, make sure that the floor is free of all
obstructions.
Carefully place dishwasher inside cabinet area such that is
centered in opening. Use caution when moving dishwasher to
prevent damage to cabinet, dishwasher and floor.
Front of door needs to be even with the front of adjoining cabinets.
Front levelers should allow 5/16" below underside of countertop
to top of console.
Check that dishwasher is level from side to side by placing a level
against the top front section of the tub. See Figure 5a.
Figure 5a
10. Check that the dishwasher is level from front to back by taking
out the lower rack, place level on the lower rack wheel support at
the bottom of the tub. See Figure 5b.
11. Adjust levelers up or down until dishwasher is level.
Holes need to be pre-drilled using a #5 drill to secure unit.
12. Screw mounting brackets firmly to cabinet using screws provided
in literature packet. See Image Below.
Figure 5c Figure 5d
13. Open and close dishwasher door slowly. Ensure that there is
clearance to the console. Adjust accordingly until door opens
and closes freely.
Property Damage
Do not solder within 6" of the water inlet valve. Damage to
the plastic parts in the valve may occur.
Use care that no sealer, dirt, or other objects enter the valve.
Damage to the filter screen may occur.
Be sure the dishwasher is placed where the water inlet
valve will be kept from freezing. If the valve freezes, it may
rupture and flooding may occur.
Water Line
1. Flush water line before connecting it to water inlet valve to
prevent early clogging of filter screen. Place a bunched towel
over end of line to prevent splashing. Open water supply valve for
a few seconds and let water drain into a pan. Turn offwater
supply at shut-off valve.
2. Route water line to water inlet valve as shown in Figure 4.
3. While firmly pulling water supply line into 90 ° elbow, tightly
connect water supply to water inlet valve. Supply line must be
free of kinks, scales, chips, and lubricants.
4. Turn on water supply and check for leaks.
Electrical Supply
1. Remove junction box cover and pull house wiring into junction
box. See Figures Below.
2. Use a UL listed conduit connector (not included) at box to
stabilize wiring.
3. Connect incoming black lead to dishwasher's black lead,
incoming white lead to dishwasher's white lead and incoming
green lead to dishwasher's green lead with wire nuts. (See
Grounding Instruction Warning). Wire nuts must be tight.
Green Wire
to Green Wire
(Ground)
Junction Blac_ Wire
Box Cover to Black Wire
Figure 6a (Hot)
Junction
Box
4. Replace junction box cover.
White Wire
to White Wire
(Neutral)
Cabinet Attach Clip
Side
Cabinet
Seal
Leveling
Leg
Cabinet
Seal
Water Line
Figure 6b
Electrical Line
check these items:
[3
[3
[3
[3
[3
Water and electrical lines are straight out in front of the
dishwasher.
All four leg levelers are positioned properly.
Cabinet Seals are positioned on the sides and top of the
dishwasher.
Cabinet Attachment Clips are attached to the cabinet on
both corners on top of the dishwasher.
Remove protective film before replacing toe and kickplate
then replace Toe and Kickplate. Note: When replacing
Toe and Kickplate hand tighten screws.
Electric Shock Hazard
Grounding Instructions:
The dishwasher must be connected to a grounded metal,
permanent wiring system or an equipment-grounding
conductor must be run with the circuit conductors and
connected to the appliance's equipment grounding terminal
or lead. It is the consumer's responsibility to contact a
qualified installer to make sure the electrical installation
conforms with the National Electrical Code and local codes
and ordinances.
Do not connect the dishwasher to the power supply until the
appliance is permanently grounded.
All wiring connections must be enclosed in the junction box.
This unit has copper lead wires.
Joining aluminum building wire to stranded copper wire
should be done by a qualified electrician using materials
recognized by UL and local codes.
Do not use an extension cord. Such use can result in fire,
electrical shock, or other personal injury.
Failure to follow these instructions could result in death or
serious injury.
1. Review Figures 7, 8 and 9 to see the different ways to connect
dishwasher to drain system. Choose method that best suits
your need.
Entry Must be
Above
,,y,,
Branch
Tailpiece
Sink at Left
Figure 7
Sink at Right
2" Drain Hose Hole
The drain hose loop must be at least 32" high f!'om the floor
to insure proper drainage.
,
If you connect to a sink drain, entry will need to be above trap.
A "Y" branch tailpiece and connector kit, not included, will make
this method easier and includes all needed fittings and
instructions. See Figure 7.
Air Gap
3. If you connect to a sink trap, local codes may require you to
install an air gap kit, (not included). The drain hose will be routed
from dishwasher to air gap inlet as shown in Figure 8. An air
gap kit is available from a plumbing supply store. (If the drain
hose is installed through the floor, an air gap is necessary).
4. If you connect to a disposer, the large end of drain hose will fit.
Figure 9(a). The knock out plug must be removed from
inside disposer inlet before making the final fit to drain
hose. See Figure 9(b).
Figure 9(a)
Cut for 5/8" connection. _Larger end
\ / of hose
/fits disposer
_YY22UYU--_T- (_ / inlet fitting.
-- Drain Hose
Cut for 3/4 connection.
/
Sink at Left //i
II I1", ',
/q // i'
_C /// " "lI ,
- &/
Drain Air Gap
!
ate
Drain
Floor into
Separate
/ Trap
Sink at Right
2" Drain Hose Hole
Figure 9(b)
The drain hose loop must be at least 32" high f!'om the floor
to insure proper drainage.
5. If the cabinet wall is wood, sand edges of hole until smooth and
rounded. If cabinet wall is metal, cover all sharp edges with
electrical or duct tape to avoid cutting drain hose.
6. Move unit back in place while routing drain hose through access
hole. Use caution to prevent damage to the dishwasher, floor and
cabinets. IMPORTANT: Make sure there are no sharp bends
or kinks that might restrict drain flow.
,
,
Secure drain hose to sink drain, disposer, or separate trap with a
clamp. IMPORTANT: Be careful not to overtighten clamp or
you may damage end of hose. Do not connect hose to
horizontal pipe between sink drain and disposer.
Be sure unit does not rest on drain hose. It should be free of
electrical components and door springs. Do not cut corrugated
drain hose. Pull excess through cabinet and place under sink.
Make sure hose does not come in contact with any sharp edges.
Electric Shock Hazard
Disconnect electrical power at the fuse box
or circuit breaker box before beginning
installation.
Failure to follow this warning could result in
death or serious injury.
Cut Hazard
Metal color panels are sharp and should be
handled with care. Wear gloves to protect
hands.
Failure to follow this warning may result in
injury.
Electric Shock Hazard
If all connections are correct, there are no leaks,
and unit runs properly, replace the kickplate
assembly before placing unit into operation.
Failure to follow this warning could result in
electric shock.
check these items:
[3
[3
[3
[3
[3
[3
[3
Water and drain lines have no kinks and move freely
behind the dishwasher.
Water supply is turned on.
Joints are free of leaks.
Wiring connections to junction box are tight all access
panels are secured back in place.
Replace kickplate. See Figure 1
Drain hose is assembled to Drain Hose Connector.
All packing materials and consumer literature have
been removed from inside unit.
[3 Dishwasher is level and securely fastened.
[3 Open and close door to make sure it does not hit
surrounding cabinet or countertop.
[3 Make sure that all wire ties are removed from the Adjustable
Rack Assembly, Versa Tray, Utility Tray and Silverware
Baskets.
Operate the machine through at
least one fill and pump-out,
checking the following items:
[3 On EDW7505HSS and EDW7505HPS press and hold
SANTIZE touchpad for 8 seconds before first use.
[3 At first fill, approximately 2 minutes make sure water
completely covers filter surface.
[3 At pump-out: (pump-out is either when the cycle is
completed or canceled, refer to the Use and Care Manual
for Start/Cancel), make sure all water is pumped out.
[3 Check water connections again for leaks.
Weight
Keep children away from the front of the dishwasher so
that they are not accidentally hit by the door during
loading or unloading or if door should unexpectedly
open. The weight of the door can cause injury.
Screws
To prevent the possibility of damage to dishwasher,
replace factory installed outer door screws with factory
supplied wood panel screws,
The EDW7505HSS & EDW7505HPS can be installed with a
fully integrated, buyer supplied custom door panel.
The custom panel should be 1/2" to 3/4" (19mm) thick.
Items provided with the unit:
Six 1V8"screws for mounting the custom wooden panel to the
dishwasher.
Tools you will need to install the Custom Wood Panel:
# 32 Drill Bit (7/64")
2 # 7 _/2"screws (Optional)
INSTALLING THE CUSTOM PANEL
Refer to the Figure 10 for instruction references.
1. Fit the handle onto the panel according to the manufacturer's
instructions. (NOTE: A handle should be used rather than a
knob. A knob does not provide enough grip.)
2. The two short screws go into the back of the panel
1 417/32"
from
the upper edge of the panel and 9/_6" f rom the edge of the
panel. Insert the short screws into the panel, leaving Vs" of
space between the screw head and the panel.
3. Hook the panel screws into the rectangular openings of the
metal panel on the dishwasher door.
4. Open the door and use the six screws supplied to secure the
panel to the door.
NOTE: The door panel cannot exceed 12 pounds.
_aX.
Thiekn_: W' _1
Weight: 12Ibs,, m ax.
2 Pilot_[ill h01e_' _
(%"dia,:× _A" m A depth)
23d="
:t
6 PiLot drillholes
Figure 10
ADJUSTING THE DOOR SPRINGS
Before you push the dishwasher into the cabinet opening, test the
door to make sure it stays in place at any angle. If it tends to fall
down, adjust the tension of the door springs on the sides of the
machine by moving them one hole farther back. If the door moves
to close, adjust the tension of the door springs on the side of the
machine by moving them one hole forward.