Table of Contents
Advertisement
13
Symptom
Causes
The menu is not displayed
Depending on the computer's set-
even when the included
tings and environment, the menu
CD-ROM is inserted into the
may not be displayed automatically.
computer's drive.
You are using a Macintosh com-
puter.
AVNavigator does not inter-
The receiver's power is not turned
act well with the receiver.
on.
The receiver or computer is not con-
nected to the LAN.
The router's power is off.
AVNavigator's network settings are
not correct.
Network connections could be
restricted due to the computer's net-
work settings, security settings, etc.
When the operating instructions
interactive mode is changed, the
settings may not be transferred to
the browser, causing AVNavigator to
stop interacting.
When the Wiring Navi,
This is because of the browser's
Operation Guide,
security function.
Interactive Manual or
Glossary is launched, a
warning about security
protection appears on the
browser.
Software updating does not
There may be a problem with your
operate well.
Internet Service Provider's network.
Remedy
Using Explorer, etc., double-click "MAIN_MENU.exe" in the
CD-ROM to execute it. A caution regarding security may
be displayed, but there is no security problem, so continue
the operation.
The provided CD-ROM includes the Windows version of
AVNavigator. The Mac OS version of AVNavigator can be
downloaded from http://www.pioneerelectronics.com.
Turn the receiver's power on. (Wait about 60 seconds after
the power turns on for network functions to start.)
After this, press Detection in AVNavigator to redetect the
receiver.
To turn this unit's power on and off from the Interactive
Manual, set Network Standby at HOME MENU d
System Setup d Network Setup to ON.
Connect a LAN cable to the receiver or computer
(page
40).
After this, press Detection in AVNavigator to redetect the
receiver.
Turn the router's power on.
After this, press Detection in AVNavigator to redetect the
receiver.
If your router does not support DHCP or UPnP, the receiv-
er's IP address must be set in AVNavigator. First set the
IP address on the receiver, then set the same address in
AVNavigator
(page
101).
After this, press Detection in AVNavigator to redetect the
receiver.
Check the computer's network settings, security settings,
etc.
After this, press Detection in AVNavigator to redetect the
receiver.
Either refresh the page's display using the browser's
refresh button or display a different page from the links so
that the setting is transferred.
This is not a problem. Perform the operation to authorize
the blocked contents.
Contact your contracted provider.
USB interface
Symptoms
Causes
The folders/files stored on a
The folders/files are currently stored
USB memory device are not
in a region other than the FAT (File
displayed.
Allocation Table) region.
The number of levels in a folder is
more than 9.
The audio files are copyrighted.
A USB memory device is
The USB memory device does not
not recognized.
support the mass storage class
specifications.
A USB hub is currently being used.
This receiver recognizes the USB
memory device as a fraud.
A USB memory device is
Some formats of USB memory
connected and displayed,
devices, including FAT 12, NTFS, and
but the audio files stored
HFS, cannot be played back on this
on the USB memory device
receiver.
cannot be played back.
The file format cannot be properly
played back on this receiver.
The USB memory cannot be
—
operated with the remote
control.
iPod
Symptoms
Causes
iPod is not recognized.
This receiver recognizes the iPod as
a fraud.
iPod touch/iPhone/iPad is
The iPod's operation may be
not recognized or otherwise
unstable.
does not operate properly.
iPod cannot be operated
—
with the remote control.
113
FAQ
Remedies
Store the folders/files in the FAT region.
Limit the maximum number of levels in a folder to 9
(page
53).
Copyrighted audio files stored on a USB memory device
cannot be played back
(page
53).
Try using a USB memory device compatible with the mass
storage class specifications. Note that there are cases
where even the audio files stored on a USB memory device
compatible with the mass storage class specifications are
not played back on this receiver
(page
53).
Connect the USB memory device and switch on this
receiver
(page
42).
This receiver does not support USB hubs
(page
53).
Switch off and on again this receiver.
Reconnect the USB device with the receiver switched off.
Change to an input other than iPod/USB, then set the input
back to iPod/USB.
Check whether the format of your USB memory device is
either FAT 16 or FAT 32. Note that the FAT 12, NTFS, and
HFS formats cannot be played back on this receiver
(page
53).
See the list of file formats that can be played back on this
receiver
(page
54).
Press iPod USB to set the remote control to the iPod USB
control mode.
Remedies
Switch off and on again this receiver.
Reconnect the iPod with the receiver switched off.
Change to an input other than iPod/USB, then set the input
back to iPod/USB.
Try performing the operation below.
1. Press the sleep/sleep cancel button on the iPod touch/
iPhone/iPad simultaneously with the home button for at
least 10 seconds to restart the device.
2. Turn this receiver's power on.
3. Connect the iPod touch/iPhone/iPad to this receiver.
Press iPod USB to set the remote control to the iPod USB
control mode.
Advertisement
Table of Contents
