Mhl; Built-In Avnavigator; Controlling The Rest Of Your System Usb Interface; Usb Interface - Pioneer SC-LX88 Operating Instructions Manual

13

MHL

Symptom Remedy
When playing an MHL-compat- The MHL device will not operate unless power is being supplied from this receiver. When
ible device connected to the this receiver is in the Standby Through mode, power cannot be supplied due to reduced
HDMI 7/MHL terminal, the Standby power consumption. Because of this, the MHL device will not operate. This is not a mal-
Through function does not work and function.
the power turns off.
MHL-compatible device cannot be Press MHL to set the remote control to the MHL control mode.
operated with the remote control.
MHL POW ERR is displayed on the There is a problem with the power supply for the MHL device. After turning OFF the
display. receiver, disconnect the MHL device, connect the MHL device again and then turn ON
the power of the receiver.
If the error is displayed even though the above operation is repeated several times,
there is a problem with the receiver or the MHL device. Disconnect the power cable and
request repair.

Built-in AVNavigator

Symptom Cause
AVNavigator does not inter- The receiver's power is not turned
act well with the receiver. on.
The receiver or computer is not
connected to the LAN.
The router's power is off.
Network connections could be
restricted due to the computer's
network settings, security settings,
etc.
In the middle of Wiring Navi, This is to avoid failure of the
you are instructed to turn receiver due to a short-circuit
off the power of the unit and between cables or from static
then connect other equip- electricity.
ment or speakers.
When the Wiring Navi or This is because of the browser's
Interactive Operation Guide security function.
is launched, a warning about
security protection appears
on the browser.
AVNavigator screen is not This receiver's IP address has not
displayed on the browser. been entered into the browser
correctly.
Receiver settings cannot be JavaScript is disabled on the inter-
made from a browser. net browser.
The browser is not compatible with
JavaScript.
Remedy
Turn the receiver's power on. (Wait about 60 seconds after
the power turns on for network functions to start.)
Connect a LAN cable to the receiver or computer (page
43 ).
Turn the router's power on.
Check the computer's network settings, security settings,
etc.
Per the Wiring Navi instructions, turn OFF the power
of the receiver. As long as the browser has not quit,
Wiring Navi resumes guidance upon turning ON the
receiver.
This is not a problem. Perform the operation to authorize
the blocked contents.
Check the receiver's IP address and enter it correctly in the
browser (page 107 ).
Enable JavaScript.
Use an internet browser that is compatible with JavaScript.

USB interface

Symptom Cause
The folders/files stored on a The folders/files are currently stored
USB memory device are not in a region other than the FAT (File
displayed. Allocation Table) region.
The number of levels in a folder is
more than 9.
The audio files are copyrighted.
A USB memory device is The USB memory device does not
not recognized. support the mass storage class
specifications.
A USB hub is currently being used.
This receiver recognizes the USB
memory device as a fraud.
A USB memory device is Some formats of USB memory
connected and displayed, devices, including FAT 12, NTFS, and
but the audio files stored HFS, cannot be played back on this
on the USB memory device receiver.
cannot be played back.
The file format cannot be properly
played back on this receiver.
The USB memory cannot be —
operated with the remote
control.
Over Current shows in the —
display.
120
FAQ
Remedy
Store the folders/files in the FAT region.
Limit the maximum number of levels in a folder to 9 (page
58 ).
Copyrighted audio files stored on a USB memory device
cannot be played back (page 58 ).
Try using a USB memory device compatible with the mass
storage class specifications. Note that there are cases
where even the audio files stored on a USB memory device
compatible with the mass storage class specifications are
not played back on this receiver (page 58 ).
Connect the USB memory device and switch on this
receiver (page 44 ).
This receiver does not support USB hubs (page 58 ).
Switch off and on again this receiver.
Reconnect the USB device with the receiver switched off.
Change to an input other than iPod/USB, then set the input
back to iPod/USB.
Check whether the format of your USB memory device is
either FAT 16 or FAT 32. Note that the FAT 12, NTFS, and
HFS formats cannot be played back on this receiver (page
58 ).
See the list of file formats that can be played back on this
receiver (page 58 ).
Press iPod USB to set the remote control to the iPod USB
control mode.
There is a problem with the power supply for the USB
memory. After turning off the receiver, disconnect the USB
memory, connect the USB memory again and then turn on
the power of the receiver.
If Over Current is displayed even though the above opera-
tion is repeated several times, there is a problem with the
receiver or USB memory. Disconnect the power cable and
request repair.