High-Speed Shooting - FujiFilm FinePix FinePix S9600 Owner's Manual

PHOTOGRAPHY MENU
PHOTOGRAPHY MENU
A WHITE BALANCE ( SELECTING THE LIGHT SOURCE )
WHITE BALLANCE WHITE BALLANCE
:
OFF OFF AUTO AUTO
1 :
AUTO AUTO
:
OFF OFF
:
2
: 0
: S E T S E T
AUTO: Automatic adjustment
(shooting to show the ambience of
the light source)
O
: Custom white balance type 1
P
: Custom white balance type 2
6
: Shooting outdoors in good weather
7
: Shooting in shade
✽ When the flash fires, the white balance setting (excluding custom white balance) for the flash is used. Consequently,
to achieve a particular effect, the flash mode should be set to Suppressed flash (➡P.53).
●
!
The color tones may vary depending on the shooting conditions (light source, etc.).
1
1 0
CUSTOM 1
CUSTOM
:
OFF OFF AUTO AUTO
1 : A U T O A U T O
:
OFF OFF
:
2
:
0
: SET SET
0 2
2
CUSTOM WB CUSTOM WB
NEW WB NEW WB
NOT CHANGE NOT CHANGE CANCEL CANCEL
Beep
66
✽ Displaying the menus (➡P.63)
Available Photography modes: N, M, <, >
Change the white balance setting to suit for the
surroundings and lighting.
In "AUTO" mode, the correct white balance may not
be achieved for subjects such as close-ups of
people's faces and pictures taken under a special
light source. Select the correct white balance for
the light source. See P.151 for more information on
the white balance.
9
: Shooting under "Daylight" fluorescent
lamps
0
: Shooting under "Warm White"
fluorescent lamps
-
: Shooting under "Cool White"
fluorescent lamps
8
: Shooting in incandescent light
Custom white balance
Use this setting to set the white balance for the
ambient natural or artificial lighting in images. Use
this setting to achieve special effects also.
O P
1 Select custom white balance " " or " ".
2 Press the "MENU/OK" button.
Hold a piece of white paper under the light source
for setting the white balance, so that it fills the
entire screen. Then press the shutter button to set
the white balance.
●
!
The white balance setting does not affect the image shown
on the screen.
To use the white balance set previously, press the
"MENU/OK" button without pressing the shutter
button.
3
COMPLETED ! COMPLETED !
SET SET CANCEL CANCEL
6 6
N N N
ISO 200 ISO 200 ISO 200
OVER OVER
OVER OVER or UNDER UNDER
◆ ◆
Example
You can change the white balance for a photographed image by using colored paper instead of white
paper.
â HIGH-SPEED SHOOTING
Available Photography modes: B, √, À, U, ,, /, N, M, <, >

HIGH-SPEED SHOOTING

HIGH-SPEED SHOOTING
:
OFF OFF
1 : AUTO AUTO
: ON ON ON ON
:
OFF OFF
2
: 0
:
SET SET
6 6
N N N
When the correct exposure is measured,
"COMPLETED !" appears.
Press the "MENU/OK" button to confirm the setting.
●
!
The specified custom white balance is retained until it is
reset. This setting is retained even if the batteries are
removed.
●
!
Adjust the custom white balance again when changing the
sensitivity setting.
●
!
After taking the picture, check the color (white balance)
setting for the image.
i Set "IMAGE DISP." to "1.5 SEC", "3 SEC" or "CONT" in the
"SET-UP" menu (➡P.101).
w
i Set the Power switch to " " (➡P.31).
When [OVER] or [UNDER] appears, the white
balance was not measured at the correct exposure.
Set the exposure compensation again, using a
negative value (–) when [OVER] appears and a
positive value (+) when [UNDER] appears.
High-speed shooting mode reduces the time
required for focusing when pressing the shutter
button down halfway.
h Focal range
Wide-angle: approx. 2 m (6.6 ft.) to infinity
Telephoto: approx. 4 m (13.1 ft.) to infinity
●
!
When this function is active, higher sensitivity settings will
increase the amount of speckling in your images. This is
normal and does not affect the photographed image.
●
!
When taking pictures while the HIGH-SPEED SHOOTING
mode is set to "ON", the batteries will run down more quickly.
3
67