Subscribe to Our Youtube Channel
Related Manuals for Navman Fish 4350
Summary of Contents for Navman Fish 4350
- Page 1 F I S H 4 3 5 0 / 4380 F I S H F I N D E R Installation and Operation Manual English....2 Español... 28 Português..59 NAV MAN...
-
Page 2: English
Always ensure that adequate fuel is carried onboard for the intended trip plus a reserve to allow for unforeseen circumstances. This manual represents the FISH 4350 and FISH 4380 as at the time of printing. Navman NZ Limited reserves the right to make changes to speciÞ cations without notice. -
Page 3: Table Of Contents
Contents 1 In tro duc tion.....................4 1-1 BeneÞ ts of the FISH 4350 and FISH 4380............. 4 1-2 How the FISH 4350 and FISH 4380 work ............4 2 Basic Op er a tion ..................5 3 Setting up the FISH 4350 and FISH 4380..........7 3-1 Setup >... -
Page 4: Introduction
Using SBN Technology, the Navman Þ shÞ nder The Navman Þ shÞ nder can be used to Þ nd Þ sh, analyses the reß ections from each pulse, Þ lters to locate features on the bottom such as reefs false returns and displays what is in the water or wrecks and to help recognize favourite Þ... -
Page 5: Basic Operation
If the Þ shÞ nder is wired for auto power, it turns turn off the Þ shÞ nder and refer to the section on on automatically whenever the boat’s ignition Troubleshooting in Appendix B.) is turned on. This ensures that the engine NAVMAN FISH 4350 / 4380 Installation and Operation Manual... -
Page 6: Simulate Mode
1. Press MENU twice to show the Setup 2. Press to dim or menu. to brighten. 2. Highlight Simulate. 3. Press to conÞ rm. 3. Press to select On or Off. NAVMAN FISH 4350 / 4380 Installation and Operation Manual... -
Page 7: Setting Up The Fish 4350 And Fish 4380
3 Setting up the FISH 4350 and FISH 4380 Press MENU twice to show the Setup menu, then select a particular option using the cursor keys. (Section 2 Basic Operation, describes how to use the keys in more detail.) The Setup menu and options are summarized below. The factory default settings are shown where applicable. -
Page 8: Setup > System
Interpreting the display, for more information. Fish Þ lter Use this to select the minimum Þ sh symbol size to be detected and displayed. There is a choice of: Small, Medium and Large. NAVMAN FISH 4350 / 4380 Installation and Operation Manual... -
Page 9: Setup > Fuel (Fish 4380 Only)
Þ lling menu, then it to capacity. After Þ lling, note the reading from select Fuel: the fuel dispenser’s gauge. Note: Beware of air pockets, especially in underß oor tanks. NAVMAN FISH 4350 / 4380 Installation and Operation Manual... -
Page 10: Setup > Data
1. Select Data setup, and press between 5 mins, 10 mins, 20 mins, 1 hour and 2. Use to move from data Þ eld to 2 hours and press to conÞ rm. data Þ eld. NAVMAN FISH 4350 / 4380 Installation and Operation Manual... -
Page 11: Setup > Logs
These can be positioned anywhere suitable on alarm trigger value the boat. See section 6-4 Wiring options. sec battery voltage is battery less than the alarm trigger value sec fuel remaining equals fuel the alarm trigger value. NAVMAN FISH 4350 / 4380 Installation and Operation Manual... -
Page 12: Setup > Units
ß ow characteristics. Temperature Obtain an accurate measurement of the boat's speed from a GPS receiver; or by following an- The factory settings should be sufÞ ciently accu- NAVMAN FISH 4350 / 4380 Installation and Operation Manual... -
Page 13: Using The Fish 4350 And Fish 4380
Note: Boat illustrated uses a through hull transducer 4 Using the FISH 4350 and FISH 4380 This section explains how to interpret the examples of some of the different sonar sonar displays and how Þ sh are detected and displays. - Page 14 Location of the Þ sh or object. (The area • Frequency and cone width Depth 200 kHz The pulse generated by the FISH 4350 and 15° FISH 4380 transducer travels down through the water, spreading outwards to form a rough cone shape. Inside the cone, the return signals are the strongest.
- Page 15 Þ sh is hidden by the strong echoes off the bottom and is not shown on the display Þ sh is visible on the display Navman Þ shÞ nders display the most recent events on the right of the screen. Moving boat 1 minute ago 30 seconds ago When the Þ...
-
Page 16: Fish Detection And Display
If there is a current, the Þ sh will often large Þ sh be found downstream of the feature. symbols When fishing with the FISH 4350 and FISH - with or 4380 with the Fish symbols Off, a weak fuzzy without band may appear between the bottom trace depth. -
Page 17: Gain
• 4-3 Gain Gain (sensitivity) controls the amount of detail Note: The Gain mode displayed on the FISH 4350 and FISH 4380. automatically changes Understanding how to set suitable Gain settings to Manual Gain if the is important for optimum performance. -
Page 18: Range
Range is the vertical depth displayed on the FISH 4350 and FISH 4380. To change between Auto Range and Manual The Navman Þ shÞ nder has two range modes, Range, hold the + or -. The Range mode is Auto Range and Manual Range: displayed at the bottom of the screen. -
Page 19: Sonar Display
See section 4-4 Range, for information about Showing the bottom as a ß at trace can make it adjusting the Zoom Range and Zoom Offset. easy to compare the echo strengths shown in the NAVMAN FISH 4350 / 4380 Installation and Operation Manual... -
Page 20: Sonar A-Scope Display
If the number essential for an accurate fuel economy reading. of engines is set to 0, the fuel features are See section 3-8 Setup > Calibrate. turned off.) NAVMAN FISH 4350 / 4380 Installation and Operation Manual... -
Page 21: Data Display
(Select from 5 minutes to 2 hours) 6 Installation and Maintenance Correct installation is critical to the performance of the FISH 4350 and FISH 4380. There are two components to install, the display unit and the transducer. It is vital to read the entire installation section of this manual before attempting to install the components. -
Page 22: Wiring Options
Bracket Mounting excessive vibration. The bracket can be tilted 1. Fix the mounting bracket onto the boat using the and rotated so the FISH 4350 and FISH 4380 three stainless steel screws. Do not overtighten can be removed after each use. -
Page 23: Systems Of Several Instruments
See the Auto power wiring diagram. the ignition is on. Auto power option If the external beeper or light requires more than 200 mA total, Þ t a relay. Consult your Navman To ignition system dealer for more advice. Fuse... -
Page 24: Cleaning And Maintenance
Cover or remove a transom-mounted When not in use, the FISH 4350 or FISH 4380 transducer when repainting the hull. If painting can be removed from the installation bracket and... -
Page 25: Appendix B - Troubleshooting
Repairs to the product may only be carried out b) The transducer may have been damaged by a service centre approved by Navman. If the during launching, running aground or product must be sent into a service centre for while underway with debris etc. - Page 26 Check that the number of engines is set low. See section 2 Basic Operation, to adjust to 2. See section 3-3 Setup > Fuel. NAVMAN FISH 4350 / 4380 Installation and Operation Manual...
- Page 27 Reduce the gain setting (see section 4-3 rate is shown. See section 3-3 Setup > Fuel. Gain). 13. There is no reading for fuel economy: c) Decrease the Range. a) The boat must be travelling through the NAVMAN FISH 4350 / 4380 Installation and Operation Manual...
- Page 28 +39 1096 80150 Mexico R.O.C. e-mail: info@nuovarade.com Mercury Marine de Mexico Ph: +886 7 831 2688 web: www.plastimo.it Anastacio Bustamente #76 Fax: +886 7 831 5001 Interior 6 Colonia Francisco e-mail: seaÞ rst@seed.net.tw NAVMAN FISH 4350 / 4380 Installation and Operation Manual...
- Page 30 Made in New Zealand MN000240B NAVMAN Lat 36° 48.404’S...
Need help?
Do you have a question about the Fish 4350 and is the answer not in the manual?
Questions and answers