Auto Channel Setting; Manual Channel Setting - Philips Show View VR1600 User Manual

Auto Channel Setting

If you move to another place, you may
need to tune the VCR tuner again for
your new residential area.
1
Perform Auto Channel Set
1 Press VCR.
2 Press MENU.
3 Press 5 or ∞ to select "AUTO
TUNER SET UP", then press OK/
STATUS.
4 Press 5 or ∞ to select your country's
name, then press OK/STATUS.
5 Press 5 or ∞ to select your preferred
language, then press OK/STATUS.
6 Press 5 or ∞ to select "AUTO CH.
SET", then press OK/STATUS.
AUTO CH. SET
PLEASE WAIT
0 – – – – – + – – – – – – – – + – – – – – +
END : MENU
Beginning
The Auto Set screen appears, and
remains on screen while the recorder
searches for receivable stations.
As Auto Channel Set progresses,
the " " mark on the screen moves
from left to right.
Wait until the screen as shown in step 2
appears.
•
When you connect VCR to TV equipped
with T-V Link,EasyLink, Megalogic,
SMARTLINK, Q-Link, DATA-LOGIC
or NEXTVIEWLINK function via fully
wired 21-pin SCART cable and the TV is
turned on, the VCR automatically
performs Follow TV instead of Auto Set
Up.
Confirm Programmed Channel
2
Information List
Once it is completed, "AUTO CH. SET
COMPLETED" is displayed on the
screen for about 5 seconds.
The screen mentioned in step 2 of
"Follow TV" ( P.16) will appear after
5 seconds, or if you press MENU.
• The blueback screen and the
programme currently being broad-
cast by the blinking station
apppear alternately for 8 seconds each.
• To view the next page, use the 5∞
2 3 buttons on the remote control.
The stations located in the selected
country appear at the top of the list.
• The Guide Channel numbers will
also be set automatically during Auto
Channel Set.
3
Finish Setting
Press MENU to exit the menu opera-
tions.
Notes:
• If you perform Auto Channel Set when the
aerial cable is not connected properly,
"NO TV SIGNALS" appears on the screen
in step 2. When this happens, make sure of
the aerial connection and press OK/
STATUS; Auto Channel Set will take place
again.
• Depending on reception conditions, the
stations may not be stored in order, and
the station names may not be stored
correctly.

Manual Channel Setting

When you want to do channel setting
End
manually, perform the following
procedures as required.
• If you want to ..........
.......... add channels (See below)
.......... delete unwanted channels
(See page 18)
.......... change the channel
positions (See page 18)
.......... perform fine-tuning (See
page 18)
.......... descramble programmes
when receiving scrambled
broadcasts (See page 18)
.......... change station names (See
page 18)
• If you live in Eastern Europe, see
INFORMATION on page 18 also.
If you want to add channels
Access Programmed Channel
1
Information List
1 Press VCR.
2 Press MENU.
3 Press 5 or ∞ to select " MANUAL
TUNER SET UP", then press
OK/STATUS.
— 17 —
2
Select Channel Position
1 Press 5∞ 2 3 until a vacant
position in which you want to store a
channel begins blinking.
(Ex.) To store in position 12.
PR CH ID PR CH
01 25 ARD 08 C26 E-SP
02 CDB SKY1 09 55 WEST
03 10 ZDF 10 C24 SAT1
04 C65 RAI1 11 C23 OSF
05 C31 BBC1 12
06 C32 BBC2 13
07 C33 3SAT 14
SELECT: 5 ∞
EDIT : OK
ERASE : CLEAR
END : MENU
The blueback screen and the
programme currently being broadcast
by the selected channel appear
alternately for 8 seconds each.
2 Press OK/STATUS. The Manual
Channel Set screen appears.
3
Set New Channel Information
1 Press 5 or ∞ to change the band
between CH (regular) and CC
(cable), then press 3.
PR CH ID FINE DECODER
12 CC25 – – – – +/– OFF
SELECT : 5∞
CURSOR POSITION :
CONFIRM : OK
END : MENU
The blueback screen and the
programme currently being broadcast
by the selected channel appear
alternately for 8 seconds each.
2 Press the Number buttons to input
the channel you want to store.
• Input "0" before any single number
entries.
• To input the registered station name
(ID – P.19), press 3 until "----"
(ID setting) begins blinking, then
press 5 or ∞.
• For fine tuning adjustment, press 3
until "+/–" begins blinking, then
press 5 or ∞. While tuning, "+" or
"–" appears.
• When storing a channel that sends
scrambled broadcasts, press 3 until
"OFF" (Decoder setting) blinks,
then press 5 or ∞ to set "DE-
CODER" to "ON" ("OFF" is the
default setting).
When "A/V2 SELECT" is set to
"A/V" or "SAT", the "DECODER"
setting cannot be changed ( P.32).
ID
– – – –
– – – –
– – – –