Insert Editing - Philips Show View VR1600 User Manual

A
DVANCED

Insert Editing

Recorder
VR 1600 VIDEO CASSETTE RECORDER
STANBY/ON
S-VHS ET DIGITAL TBC/NR
/
TIME BASE CORRECTOR FLYING ERASE HEAD TAPE MANAGER
INSERT
OPEN AV FRONT CONNECTORS SYNCHRO EDIT
+8
4
0
6
AUDIO DUBBING
S-VIDEO VIDEO L AUDIO R -15 dB
1 NORM 2
Audio/Video signal
S-Video
signal
Player
Another VCR
1
Make Connections
Connect the player's VIDEO OUT or
S-VIDEO OUT and AUDIO OUT
connectors to your VCR's VIDEO or
S-VIDEO and AUDIO input connectors
on the front panel.
2
Set Input Mode
Press NUMBER button "0" and/or
PROGRAMME 5/∞ or CH 5/∞ so
that "L-F" for the VIDEO/AUDIO
input connectors, or "S-1" for the
S-VIDEO/AUDIO input connectors
appears on the display window.
3
Locate End Point
Load the recording cassette into your
VCR, and play it back to determine the
edit-out point (the end of the segment
to be replaced) using the SHUTTLE
ring, Jog dial or pressing REW 1
or FF ¡ and PAUSE/STILL 8.
4
Reset The Counter
Press CLEAR to change the counter
display to "0:00:00".
5
Locate Start Point
Determine the edit-in point (the
beginning of the segment to be
replaced) using the SHUTTLE ring,
O
PERATIONS
Your VCR
STOP/EJECT
SUPER VHS
REC/OTR
SP SLP REVIEW
PAUSE/STILL PLAY
PROGRAMME
VPS/PDC
VCR
TURBO
DRIVE
DIGITAL STEREO
Jog dial or pressing REW1 or
FF¡ and PAUSE/STILL 8.
• Be sure to engage the Still mode at
the edit-in point.
6
Engage Insert Editing Mode
Press INSERT on the front panel.
• Your VCR enters the Insert-Pause
mode.
"‡ ‡ ‡ ‡ ‡ " (REC), # # # # # (PLAY) and 8
(PAUSE) lights up on the display
window.
• The TV screen changes from the
still picture to the input source you
are going to record.
7
Start Editing
Load the source cassette and play back
the segment that is to be inserted.
When you reach the start of the section
of the source tape that you wish to
insert, press PAUSE/STILL 8 to start
the tape in your VCR; Insert Editing
begins at this point.
8
End Insert Editing
At counter "0:00:00", Insert Editing
will stop automatically while the tape
continues running in the Play mode. If
you wish to stop Insert Editing before
the specified edit-out point, press
CLEAR.
(C
Insert editing replaces part of the recorded scene with new
material. Both the picture and Hi-Fi audio soundtrack are
replaced with new ones, while the normal audio soundtrack
remains unchanged. If you wish to change the normal audio
track as well, use the audio dubbing function simultaneously.
Use your VCR as the recorder.
Source tape
Before insert editing
Recorded tape
After insert editing
— 40 —
)
ONTINUED
Normal
Audio track
Video/Hi-Fi
audio track
For AV Insert Editing
If you want to replace the picture, Hi-Fi
audio soundtrack and normal audio
soundtrack all at the same time, press
AUDIO DUBBING after pressing
INSERT in step 6 . "‡ ‡ ‡ ‡ ‡ " and # # # # # blink
and 8 lights up on the display window.
Notes:
• Insert editing is not possible with
cassettes whose safety tab has been
removed.
• When insert editing is performed on a
tape that has been recorded on another
VCR, the inserted portion may appear
distorted.
• In Insert Editing, the recording speed
(SP/LP) is determined by the previous
recording to be replaced. If the previous
recording's speed changes within a single
edit, the inserted picture will be distorted
at the switching point.
• A small portion of the recording which
precedes an insert edit may become
erased.
• Insert Editing is also possible using the
rear panel AV1 (L-1) IN/OUT or AV2
(L-2) IN/DECODER connector. When
using these connectors, make sure to
select the correct input mode in step 2.
• Insert Editing does not function with SLP
recorded tape.