Universal Remote Control Easy Clicker UR2-211 Operating Manual

Operating Manual
1
Introduction
For Easy Clicker This remote control is designed
to operate most Digital, Analog
Cable boxes, IPTV set top boxes
UR2-211 and TVs.
2
Replacing Batteries
Before you program or operate the
remote control, you must install
two new AA alkaline batteries.
STEP1 Remove the battery com-
partment cover from the
back of your remote control.
STEP2 Check battery polarity
carefully, and install the
batteries as shown in the
illustration below.
STEP3 Replace the battery com-
partment cover.
4
Programming the Remote Control
*Note : In this section, when you are instructed to press a [DEVICE] button, that means you should press either
the CBL or TV button, depending on which device you are programming the remote to operate.
A. Quick Set-Up Method A. Quick Set-Up Method
Universal Remote Control, Inc.
(Refer to the Section 5 Quick Set-up table of codes)
www.universalremote.com
STEP1 Turn on the equipment you want to program. To program your TV, turn on the TV.
OCE-0082E Rev 04 (09/03/12)
3
Button Functions
Macro Button
For future use
STEP2 Point the remote at the toward the equipment and
component and press and enter the three-digit code
hold the [DEVICE] key for 5 number assigned to your
seconds until the Device LED brand from the code tables.
blinks off and turns back on. If there are more than one
Continue holding the [DEVICE] three-digit number listed for
key and press the numberkeys, your brand, try one code
one at a time, starting with 1, number at a time until your
then2, 3...0. Stop pressing equipment turns off.
the number keys when the
*Note: You can verify that you have
device turns off.
selected the correct code by
STEP3 Release the [DEVICE] key to pressing the [POWER] button.
save the code. The Device The equipment should turn
LED will blink twice to
back on. Then try all of the
confirm the code is stored. functions on the remote
control (i.e. volume, mute,
Repeat the steps above for all
etc.) to ensure you have the
components(CBL, TV).
correct code. If any of the
B. Manual Programming functions do not operate as
B. Manual Programming
they should, repeat the
The remote control can be programmed
instructions from STEP 3
by entering a three-digit code number
above using the next three
that corresponds to particular brands
digit code number from the
and models of equipment. The three-
brand list.
digit code numbers are listed in the
code tables sections of this instruction STEP4 Store the three-digit code
manual. by pressing the same
[DEVICE] button once again.
STEP1 Turn on the equipment that
The device LED will blink
you want the remote con-
twice to confirm that the
trol to operate (Cable Box or
code has been stored.
TV).
C. Auto Search Method C. Auto Search Method
STEP2 Press the [DEVICE] button
and the [OK/SEL] button
If none of the three digit code numbers
simultaneously for 3 seconds.
assigned to your brand of equipment
The corresponding device
works, or the code table does not list
LED will turn on indicating
your brand, you can use the Auto
that it is ready to be pro-
Search Method to find the correct
grammed. The LED will remain
three-digit code number for your
on for 30 seconds. The next
equipment by following steps:
step must be entered while
STEP1 Turn on the equipment that
the LED is on.
you want the remote control
STEP3 Point the remote control
to operate (Cable Box or TV).
STEP2 Press the [DEVICE] button STEP1 Press the [CBL] button.
and the [OK/SEL] button
STEP2 Press the [All OFF] button
simultaneously for 3 seconds.
and the [OK/SEL] button
The device LED will turn on
simultaneously for 3 seconds.
indicating that it is ready to
The [CBL] button will turn
be programmed. The LED
on for 30 seconds.
will remain on for 30 seconds.
The next step must be enter-
STEP3 Press the first [Device] button
ed while the LED is on.
you want to store in the
[ALL OFF] button and then
STEP3 Press the [CH5] or [CH6]
the [POWER] button. Repeat
button one at a time or keep
this for other Device until
it pressed. The remote will
you have stored all the
emit a series of Power
desired power commands
ON/OFF code signals. Release
the [CH5] or [CH6] button into the [ALL OFF] button.
as soon as the equipment
STEP4 Press the [CH5] button to
turns off.
save the power commands
*Note: You can verify that you have you stored. The [CBL]
selected the correct code by
button will blink twice to
pressing the [POWER]
confirm the Device have
button. The equipment
been saved.
should turn back on. Then
E. Programming Volume
E. Programming Volume
try all of the functions on
the remote control (i.e. Control
Control
volume, mute, etc.) to ensure
By default, the VOL+, VOL- and MUTE
you have the correct code. If
keys operate through your TV. If you
any of the functions do not
operate as they should, would like those keys to operate
repeat the instructions from
those functions on a different device,
STEP 3 above to continue
follow these steps.
the Auto Search Method.
STEP1 Press the [OK/SEL] button and
STEP4 Press the same [DEVICE]
[CBL] button simultaneously
button to store the code.
for 3 seconds. The device LED
The Device LED will blink
will turn on for 30 seconds.
twice to confirm that the
The next step must be
code has been stored.
performed while the LED is on.
D. Programming the All Off
D. Programming the All Off
STEP2 Press the [VOL+] button.
Button Button
The device LED will blink.
This allows you to program the All Off
STEP3 Press the [DEVICE] button
button so it can send up to two power
corresponding to the device
On/Off commands with one button
press. that you would like the