Page 1
® 1 SR IGITAL HEATER PEAKER YSTEM Setup Guide | Guía de instalación | Guide d’installation...
Page 2
They will help you set up and operate your system properly and enjoy its advanced features. Please save these guides for future reference. All Bose products must be used in accordance with local, state, federal, and industry regulations. The lightning flash with arrowhead symbol within an equilateral triangle alerts the user to the presence of uninsulated, dangerous voltage within the system enclosure that may be of sufficient magnitude to constitute a risk of electric shock.
Product overview The CineMate 1 SR digital home theater speaker system takes the place of your TV's built-in speakers. This is done by connecting your TV's audio output to the TV audio input (TV Input) on the CineMate system (see figure below).
Unpacking As you carefully unpack the carton, if any part appears damaged, do not attempt to use it. Notify Bose or your authorized Bose dealer immediately. For Bose contact information, refer to the address sheet included in the carton. Be sure to save all of the packing materials. These provide the safest means for any necessary shipping or transporting.
Guide Wall mounting kit The speaker array can be mounted on the wall. If you wish to do this, contact Bose to purchase the WB-135 Wall Mount Kit. CAUTION: Do not use any wall-mounting hardware other than the WB-135 Wall Mount Kit to mount the speaker array on a wall.
YSTEM ETUP Putting the system together ® Note: The CineMate 1 SR system uses the reflective surfaces of your room to deliver wide, spacious sound. For best sound quality, the speaker array should not be placed inside a cabinet, or diagonally in a corner. Note: To avoid wireless interference, keep other wireless equipment, such as wireless computer network routers, cordless phones, microwave ovens, or other WIFI-enabled audio/video devices away from the speaker array and Acoustimass...
Page 10
YSTEM ETUP B. Plug one end of the selected audio cable into the corresponding audio output connector on your TV. Note: If you are using an optical cable, be sure to remove the protective cover from the plug. When inserting the plug into the connector, make sure it is pushed in all the way. You may sense a slight resistance before you feel it click into place.
Note: If you currently have audio/video sources such as a cable/satellite set-top box and a DVD player connected to your TV, do not disconnect them. The audio output from the source should be connected to the TV and to the CineMate 1 SR speaker array. Refer to “Product overview” on page 6.
YSTEM ETUP Step 3: Connect a power cord to the speaker array What you need for this step: Power cord Plug the small end of the power cord into the connector labeled Power. Note: Do not plug the power cord into an AC power outlet at this time. You will be instructed to do this later in the setup process.
YSTEM ETUP Step 4: Route the cables A. Arrange the cables as needed for your setup location. B. OPTIONAL: Secure cables under the clips in the channel running along the length of the speaker array. Cable clip Channel English – 13...
YSTEM ETUP Step 5: Position the speaker array What you need for this step: OPTIONAL: Speaker array extension feet CAUTION: The speaker array must be placed on a solid flat surface. For proper support, all of the feet on the bottom of the speaker array must be resting on the table top. A.
YSTEM ETUP ® Step 6: Set up the Acoustimass module What you need for this step: Acoustimass module Rubber feet Power cord CAUTION: Choose a stable and level surface for the Acoustimass module. Vibration can cause the speaker to move, particularly on smooth surfaces like marble, glass, or highly polished wood.
Page 16
YSTEM ETUP D. Place the Acoustimass module according to the following guidelines: • For best sound quality, stand the Acoustimass module on its feet along the same wall as your TV, or along any other wall in the front third of the room. •...
YSTEM ETUP First time startup Step 1: Install the remote batteries What you need for this step: (2) AA (IEC LR6) batteries Remote control A. Slide the battery cover off the back of the remote control. AA (IEC LR6) batteries (2) Battery cover B.
YSTEM ETUP A. Point the remote at the speaker array and press the system power button. B. Check that the power indicator on the speaker array is on (white), indicating the system is on, and that the status indicator is off. Status Power If the Status indicator is blinking orange:...
• If your TV has a variable audio output, the TV volume may need to be turned up enough to hear sound from the speaker array. Note: To confirm your TV speakers are off, press Mute on the Bose remote and check that no sound is coming from the TV.
Page 20
2011 Bose Corporation, The Mountain, Framingham, MA 01701-9168 USA AM343500 Rev 00...