Table of Contents
Related Manuals for AMC XOi
Summary of Contents for AMC XOi
- Page 3 * System for total 4 Zones * System with 8 Sources * Only RJ45 & Speaker Wires used for installations from XOi main unit to all zones * Two ways AMC propriotary Digital Data Communication System between XOi main unit and keypads in all zones * Designed with cascade feature for keypad XK1 * Volume Control &...
- Page 4 FRONT PANEL 1. Power Switch (Standby / Off) & Blue LED Front Rear Doorbells 1 & 2 Tel Lines 1 & 2 AMC PDM1 Zone 2 Zone 3 7. 12VDC 8. Keypads & Remote Sources 9. Speaker Terminals 10. RS232 11.
-
Page 5: Rear Panel Connections
FRONT PANEL CONTROLS 1. Power Switch (Standby / Off) & Blue LED The Power Switch turns AMC XOi "Standby" or "Off" The Blue LED will be lit up during "Standby", will be turned off during "Off" 2. Zone LED & 4 square Recesses Each of these LEDs indicates, when lit, that its zone keypads are turned on. - Page 6 The 8 source buttons independently select any of the four local sources ( Source 1 to 4) connected to the rear panel of AMC XOi main unit and four Remote Sources (Source R5 to R8) connected to the XU1 of Zone 1 to 4.
- Page 7 8. JK2 (RJ45) (TO XOi Rear Panel) Use Cat-5 cable to connect from the JK2 of XK1 to RJ45 of specific Zone on XOi Rear Panel (or JK3 of Main XK1 - option) 9. JK3 (RJ45) (To Another XK1) Use Cat-5 cable to connect from the REMOTE SOURCE XS1 JK3 of XK1 to JK2 of Another XK1.
-
Page 8: Remote Control
Perform the same function as the volume button on the zone keypads. The volume level indicator on the keypad will respond correspondingly to the volume command from the remote control. The remote control is basically with the same functions of keys as AMC S84... - Page 9 RJ45 connector. The XOi system can accommodate 500 total feet of Cat-5 cable for each zone. For the most reliable operation, it is best that no single run of Cat-5 exceeds 250 feet.
- Page 10 Step6 The RJ45 should be firmly crimped to the Cat-5 insulation. It is necessary that the color scheme be repeated identically on each end of the wire. 3. Speaker Wire Termination at XOi It is important to keep the proper orientation of positive and negative signal for each speaker connection.
- Page 11 4. Installing the XOi The XOi is designed to be placed on a shelf or in a component rack. If you are mounting the XOi with other components,you should remove the feet. The audio sources are plugged into the four local source inputs on the back panel of the XOi using stereo RCA cables, Fig.4...
- Page 12 6. Keypad XK1 and Zone Setup The Zone number each keypad XK1 belonging to is decided by which RJ45 connector each keypad connected through Cat-5 cable from JK2 of XK1 to XOi. EQ Control and Source Grouping The keypads can be used to set specific zone functions. These are for bass and treble EQ response and source grouping.
- Page 13 "Link". This requires the use of "Y" cables to link the source inputs and IR outputs. A single mono mini-patch cable is then plugged into the "Link" jack on both XOi. This links the All Off command so when it is initiated at any of the zone keypads, all eight zones will turn off.
-
Page 14: Specifications
SPECIFICATIONS Total Zones ......... . . 4 Zones Zone 1~4 with Speaker Outputs . -
Page 15: Safety Instruction
National Fire Protection Association (Batterymarch Park, Quincy. MA 02269). Antenna Lead In Wire Antenna Ground Discharge Clamp Unit (NEC Section 810.20) Grounding Conductors (NEC Section 810.21) Ground Clamps Power Service Grounding Electrode System (NEC Art 250 Part H) AMC 21-3004... - Page 16 WELTRONICS CORP. LONDON/L.A. AMC Web: http://www.amchome.com PN: 21R-4213...