Advertisement
Connect to network
By connecting the unit to your home LAN, you can enjoy AirPlay and playback of music stored on your computer or other device.
• This unit cannot be used to play movie fi les.
• For information regarding the format of fi les supported by this unit, consult the Operating Instructions posted on the Pioneer website.
Methods of connection may vary depending on the device used. Confi rm the type of unit, and follow the appropriate instructions.
If you select method A, C or E, confi rm the LAN cable is not connected to this unit.
Connecting to a router with WPS-PBC function
Connecting
this unit
using
wireless
Yes
LAN
Connecting to a router without
WPS-PBC function
LAN
3
2
1
WAN
No
LAN
3
2
1
WAN
If you intend to connect an iPhone/iPod touch/iPad (with iOS ver 5.0 or later) to a
conventional household wireless LAN
Connecting
Connecting to a router with DHCP server function
this unit
using wired
Yes
LAN
When fixed IP must be set
(connecting to a router without DHCP
LAN
3
2
1
WAN
server function)
No
LAN
3
2
1
WAN
Wireless Direct Function
Turning on Quick Start Mode
Quick Start Mode significantly reduces the time required for startup. It also allows the unit to power on automatically using AirPlay and DLNA. Follow the steps below to turn on Quick Start Mode.
1.
2.
Connect the AC adapter.
Press the standby/on button.
After the power turns on, it takes approximately 30 seconds for the unit to
be ready to use ("power on" LED will go from flashing to solid blue).
When connection is complete, read the following instructions.
Enjoying AirPlay
1.
2.
3.
Tap AirPlay icon (
).
Select SMA.
Tap iPod icon.
A
LAN
3
2
1
WAN
If your computer or tablet PC
is equipped with wireless
C
LAN function
Yes
If your computer or tablet PC is
not equipped with wireless LAN
D
function (wired LAN only)
No
E
Yes
B
LAN
3
2
1
WAN
If your computer or tablet
PC is equipped with
C
wireless LAN function
Yes
If your computer or tablet
PC is not equipped with
D
wireless LAN function
(wired LAN only)
No
F
3.
Press the input button for 3 seconds.
The LEDs will flash blue 4 times to signal Quick Start Mode has
been turned on.
4.
Tap to play music.
A
Connections for wireless LAN using WPS-PBC function
1.
2.
Confirm that the AC adapter and LAN cable are not
Connect the AC adapter, and press standby/on button.
connected to the unit.
The power on indicator will flash blue. Wait for about 30 to 40
seconds.
LAN(10/100)
iPod/iPhone/iPad
DC IN
AUX IN
DC IN
AUX IN
6
B
Wired connection to a router with DHCP server
1.
2.
Disconnect the AC adapter before performing the
Connect the AC adapter, and press standby/on button.
connection between router and this unit.
The power on indicator will flash blue. Wait for about 30 to 40
Use a LAN cable to connect this unit and your router.
seconds.
LAN(10/100)
iPod/iPhone/iPad
DC IN
AUX IN
DC IN
AUX IN
LAN
3
2
1
WAN
C
Connection settings from a Web browser using a computer, iPhone, tablet PC or other device supporting wireless LAN
1.
2.
Confirm that the AC adapter and LAN cable are not
Connect the AC adapter, and press standby/on button.
connected to the unit.
The power on indicator will flash blue. Wait for about 30 to 40
seconds.
LAN(10/100)
iPod/iPhone/iPad
DC IN
AUX IN
DC IN
AUX IN
6
7.
6.
From the menu on the left, select "Network
When the Auto/Manual selection screen appears,
Configuration."
select "Auto."
If you wish to change the Friendly Name, select
If you are manually inputting the SSID or setting a fixed
"Friendly Name" from the menu and change the
IP with a wired connection, select "Manual." For details,
name before selecting "Network Configuration."
refer to the item "Web Control" of the Operating
Instructions.
S1000.1000.0
XW-SMA1
XX:XX
X:X
XXX:XXX
X:X
X:X
D
Using a Web browser on a computer supporting wired LAN to make connecting settings for the unit
2.
1.
Use a LAN cable to connect the unit to the computer.
Connect the AC adapter, and press standby/on button.
The power on indicator will flash blue. Wait for about 30 to 40
seconds.
LAN(10/100)
iPod/iPhone/iPad
DC IN
AUX IN
DC IN
AUX IN
6
6.
7.
If you are considering using this unit with wireless connections,
If a password is requested, input it here.
input your router's SSID, then select "Security."
Also, if input of a fixed IP is required, set DHCP to OFF here and make
the setting. For details, refer to the item "Web Control" of the Operating
Instructions.
E
Connection settings using an iOS device
If you use an iPhone/iPod touch/iPad (iOS device with iOS ver 5.0 or later) with wireless LAN connection, apply the iOS device's connecting settings to this unit.
2.
1.
Confirm that the AC adapter and LAN
Connect the AC adapter, and press standby/on
cable are not connected to the unit.
button.
The power on indicator will flash blue. Wait for about 30 to
40 seconds.
LAN(10/100)
iPod/iPhone/iPad
DC IN
AUX IN
DC IN
AUX IN
6
F
This connection allows the temporary use of this unit in places where a router is not available; when power is turned off, the Wireless Direct function is disabled and the network setting of this unit returns to the previous setting.
Wireless Direct Function
Since this kind of connection is not encoded, a minor security risk may be involved. For details, see the Operating Instructions.
1.
2.
Confirm that the AC adapter and LAN
Connect the AC adapter, and press standby/on
cable are not connected to the unit.
button.
The power on indicator will flash blue. Wait for about 30 to
40 seconds.
LAN(10/100)
iPod/iPhone/iPad
DC IN
AUX IN
DC IN
AUX IN
6
PIONEER CORPORATION
PIONEER ELECTRONICS (USA) INC.
P.O. BOX 1540, Long Beach, California 90801-1540, U.S.A. TEL: (800) 421-1404
1-1, Shin-ogura, Saiwai-ku, Kawasaki-shi, Kanagawa 212-0031, Japan
PIONEER ELECTRONICS OF CANADA, INC.
Корпорация Пайонир
340 Ferrier Street, Unit 2, Markham, Ontario L3R 2Z5, Canada TEL: 1-877-283-5901, 905-479-4411
1-1, Син-Огура, Сайвай-ку, г. Кавасаки, префектура Канагава, 212-0031, Япония
Импортер: ООО "ПИОНЕР РУС"
PIONEER EUROPE NV
Haven 1087, Keetberglaan 1, B-9120 Melsele, Belgium TEL: 03/570.05.11
125040, Россия, г. Москва, ул. Правды, д.26 Тел.: +7(495) 956-89-01
3.
4.
When the power on indicator stops flashing, press the
Within 2 minutes, press the router's WPS button.
rear-panel network setup/wireless direct button.
For information regarding router operation, consult the router's
The network indicator will change from flashing red to flashing
Operating Instructions.
purple.
WPS
network setup
wireless direct
DC IN
AUX IN
WPS
3.
The power on indicator's flashing will stop, and when
the power is fully turned on, the network indicator will
light blue.
6
3.
4.
When the power on indicator stops flashing, press and hold volume
When the network indicator lights red, connect to the
– button on the front panel, and then press and hold network
network called "Pioneer Setup:xxxxxx" from Wi-Fi network
setup/wireless direct button on the rear panel for 3 seconds.
setting on the computer, iPhone, tablet PC or other device.
The unit will reboot (the power on indicator will flash blue). Wait for
The "xxxxxx" is the device's unique identifier number.
about 30 to 40 seconds.
* Consult the appropriate Operating Instructions for information
regarding operation of the computer, iPhone, tablet PC or other device
used.
* Since this kind of connection is not encoded, a minor security risk may
network setup
wireless direct
be involved.
DC IN
AUX IN
6
8.
9.
10.
Select your router's SSID.
If you are asked to input a password, input it
If the SSID does not appear, either repeat
here.
step (6), or use step (7) to select Manual
Also, if input of a fixed IP is required, set DHCP to
and input the SSID manually.
OFF here and make the setting. For details, refer to
the item "Web Control" of the Operating
Instructions.
3.
4.
Wait for the network indicator to change from flashing to
When the network indicator lights red, start your computer's
steadily lighted red.
Web browser, and access the URL noted below to make
settings for this unit.
This may require up to 90 seconds or so.
The Web Control menu will appear.
For Safari Press Bookmark icon. Click Bonjour list (a), and then
select this unit's name ("Friendly Name") (b) in Bookmark.
http://169.254.1.1
9.
8.
When settings are completed, click on Apply.
Disconnect the LAN cable from the unit and confirm that
The unit will automatically power down.
the router's power is ON.
If you intend to use the unit in a wired configuration, use a LAN
cable to connect the unit to the router.
LAN(10/100)
iPod/iPhone/iPad
4.
3.
When the power on indicator
Press and hold input button on the front panel, and then
stops flashing, use a USB cable
press and hold network setup/wireless direct button on
to connect this unit to the
the rear panel for 3 seconds.
iPhone/iPod touch/iPad (iOS
A screen like the following should appear on the iOS device.
LAN(10/100)
iPod/iPhone/iPad
device with iOS ver 5.0 or later).
* Confirm that the iOS device has
a wireless connection to your
router.
* Confirm that the iOS device's
screen lock is disabled.
DC IN
6
3.
4.
Confirm that the unit's power on indicator stops flashing. Hold the
When the network indicator lights purple, connect to the network
unit's rear-panel network setup/wireless direct button depressed for 3
called "Wireless Direct:xxxxxx" from Wi-Fi network setting on the
seconds.
computer, iPhone, tablet PC or other device.
The "xxxxxx" is the device's unique identifier number.
The unit will begin rebooting (the power on indicator will flash blue); wait for
about 30 to 40 seconds.
* Consult the appropriate Operating Instructions for information regarding operation
of the computer, iPhone, tablet PC or other device used.
network setup
wireless direct
DC IN
AUX IN
PIONEER ELECTRONICS ASIACENTRE PTE. LTD.
253 Alexandra Road, #04-01, Singapore 159936 TEL: 65-6472-7555
PIONEER ELECTRONICS AUSTRALIA PTY. LTD.
5 Arco Lane, Heatherton, Victoria, 3202, Australia, TEL: (03) 9586-6300
PIONEER ELECTRONICS DE MEXICO S.A. DE C.V.
Blvd.Manuel Avila Camacho 138 10 piso Col.Lomas de Chapultepec, Mexico, D.F. 11000 TEL: 55-9178-4270
K002_B4_Ru
5.
The network connection settings will be performed automatically,
and when the connection is complete, the unit's indicator will
briefly change to flashing red, then light steadily blue.
5.
When the connection is established, boot your Web
browser and access the URL noted below to make settings
for this unit.
The Web Control menu will appear.
For Safari Press Bookmark icon. Click Bonjour list (a), and then
select this unit's name ("Friendly Name") (b) in Bookmark.
For Safari
a
iPod
Network
Wi-Fi Network
Wi-Fi
ON
b
Choose a Network...
0001 Setup:xxxxxx
http://192.168.1.1
11.
When settings are completed, click on Apply.
Press standby/on button.
The unit will automatically power down. Confirm that
The power on indicator will flash blue. When the power is
completely on (power on indicator lights steadily blue),
the router's power is ON.
the network indicator will light blue, indicating that
If you intend to use the unit in a wired configuration,
settings are completed.
use a LAN cable to connect the unit to the router.
6
5.
From the menu on the left, select "Network Configuration."
If you wish to change the Friendly Name, select "Friendly Name"
from the menu and change the name before selecting "Network
Configuration."
For Safari
S1000.1000.0
XW-SMA1
a
XX:XX
X:X
XXX:XXX
X:X
X:X
b
10.
Press standby/on button.
The power on indicator will flash blue. When the power is completely
on (power on indicator lights steadily blue), the network indicator will
light blue, indicating that settings are completed.
6
5.
6.
Tap the "Allow" button.
When the network indicator changes from
flashing red to steadily lighted blue, the
connection is completed.
Share Wi-Fi Settings?
network setup
wireless direct
Ignore
AUX IN
Note that the network indicator will
continue to light purple even after this
connection is established.
Thereafter, you can listen to music using
the smart phone or other device. For
details, consult the Operating
Instructions for the respective device.
iPod
Network
Wi-Fi Network
Wi-Fi
ON
Choose a Network...
0001 Setup:xxxxxx
Advertisement
