D A - Panasonic DVCPRO AJ-D410AP Operating Instructions Manual

Menu contents
MAIN menu 1 of 2 (main menu)
BATTERY
Setting
Item
options
BATTERY SELECT NiCd12 For selecting the type of battery used.
NiCd13 NiCd12:
NiCd14 NiCd13:
TYPE A NiCd14:
TYPE B TYPE A:
ANTON-D TYPE B:
IDX-D
ANTON-D: Digital battery made by Anton
IDX-D:
TYPE A NEAR 11.0V For designating type A voltage. When the
END : voltage drops below the level set here, the
11.6V battery is considered to have a minimal
: remaining charge, and a warning is
15.0V displayed. A voltage from 11.0 V to 15.0 V
is used as the setting.
TYPE A END 11.0V For designating type A voltage. When the
: voltage drops below the level set here, the
11.2V battery is considered to be flat, and a
: warning is displayed. A voltage from 11.0
15.0V V to 15.0 V is used as the setting.
TYPE B NEAR 11.0V For designating type B voltage. When the
END : voltage drops below the level set here, the
13.0V battery is considered to have a minimal
: remaining charge, and a warning is
15.0V displayed. A voltage from 11.0 V to 15.0 V
is used as the setting.
TYPE B END 11.0V For designating type B voltage. When the
: voltage drops below the level set here, the
12.5V battery is considered to be flat, and a
: warning is displayed. A voltage from 11.0
15.0V V to 15.0 V is used as the setting.
ANTON-D NEAR 11.0V For designating the voltage of the ANTON-
END : D digital battery. When the voltage drops
14.1V below the level set here, the battery is
: considered to have a minimal remaining
15.0V charge, and a warning is displayed.
voltage from 11.0 V to 15.0 V is used as the
setting.
ANTON-D END 11.0V For designating the voltage of the ANTON-
: D digital battery. When the voltage drops
13.8V below the level set here, the battery is
: considered to be flat, and a warning is
15.0V displayed. A voltage from 11.0 V to 15.0 V
is used as the setting.
IDX-D NEAR END 11.0V For designating the voltage of the IDX-D
: digital battery. When the voltage drops
12.8V below the level set here, the battery is
: considered to have a minimal remaining
15.0V charge, and a warning is displayed.
voltage from 11.0 V to 15.0 V is used as the
setting.
IDX-D END 11.0V For designating the voltage of the IDX-D
: digital battery. When the voltage drops
12.0V below the level set here, the battery is
: considered to be flat, and a warning is
15.0V displayed. A voltage from 11.0 V to 15.0 V
is used as the setting.
Remarks
NP-1B made by Sony
TRIM13 made by Anton Bauer
TRIM14 made by Anton Bauer
13.2 V NiMH type
Digital 14 V (Hitron 100) made
by Anton Bauer
Bauer
Digital battery made by IDX
A
A
36
MIC/AUDIO
Setting
Item
options
FRONT MIC ON ON: Phantom power is supplied to the
POWER OFF
OFF:Phantom power is not supplied to the
FRONT MIC –40dB For selecting the camera mic input level.
–50dB
–60dB
REAR MIC CH1 –40dB For setting the input mic level for the rear
–50dB jack AUDIO CH1 input.
–60dB
REAR MIC CH2 –40dB For setting the input mic level for the rear
–50dB jack AUDIO CH2 input.
–60dB
MIC LOWCUT CH1 ON ON: The low-cut filter is set to ON for the
OFF
OFF:The low-cut filter is set to OFF for the
MIC LOWCUT CH2 ON ON: The low-cut filter is set to ON for the
OFF
OFF:The low-cut filter is set to OFF for the
LINE CH1/CH2 +4dB For selecting the line input level of the
0dB signals to be supplied to the AUDIO CH1
–6dB and CH2 rear jacks.
REAR SEL CH1 XLR For selecting the CH1 rear input.
WIRELESS XLR:
WIRELESS: The input from the wireless
<Note>
When WIRELESS is selected, the REAR
MIC levels cannot be selected.
REAR SEL CH2 XLR For selecting the CH2 rear input.
WIRELESS XLR:
WIRELESS: The input from the wireless
<Note>
When WIRELESS is selected, the REAR
MIC levels cannot be selected.
LIMITER CH1 OFF For switching the CH1 AUDIO limiter ON or
ON OFF. This item's setting is functional only
when MANU has been selected as the
AUDIO SELECT setting.
OFF:The limiter is OFF.
ON: The limiter is ON.
LIMITER CH2 OFF For switching the CH2 AUDIO limiter ON or
ON OFF. This item's setting is functional only
when MANU has been selected as the
AUDIO SELECT setting.
OFF:The limiter is OFF.
ON: The limiter is ON.
CUE REC SEL CH1 For selecting the signal to be recorded on
MIX the CUE track.
CH2 CH1: The CH1 input signal is recorded.
MIX: The CH1 and CH2 input signals are
CH2: The CH2 input signal is recorded.
" " indicates the factory setting.
Remarks
front microphone.
front microphone.
CH1 mic input.
CH1 mic input.
CH2 mic input.
CH2 mic input.
The input from the XLR
connector is selected.
receiver is selected.
The input from the XLR
connector is selected.
receiver is selected.
mixed and recorded.