Advertisement
Quick Links
HONEYWELL SECURITY TECHNICAL BULLETIN
Subject: Control HNDR-S 4848 DVR by VideoBlox HEGS5BLX
Introduction
This document describes the Protocol Interface Translator (PIT) operation specific to the Honeywell HNDR-S
series DVR. For further details on the PIT, please refer to the PIT User manual. For further details on the DVR,
please refer to the appropriate Honeywell HNDR-S DVR manual.
Quick Start Switch Settings
Output
S1/8
Protocol
Valid
Function
Off
Address
S2/8
Switch
Address
Legend
7
0 (B/cast)
Off
Input
S3/8
Protocol
Slave Port
Baud
Bossware
On
The above setting set the PIT as follows:
Receive Betatech compatible Bossware control messages on the RS422 slave port of the PIT at 19.2K baud.
The PIT unit address (S2/1 - S2/8 to OFF position) is set to broadcast, so all addresses will be translated. If
want to control specific unit of DVR, set the dip switch S2/1 – S2/8 of PIT address and add PIT per DVR. (It is
tested the address from 1 to 128.)
Unit ID
S2/8
1
Off
2
Off
3
Off
4
Off
5
Off
:
255
On
Transmit Honeywell HNDR-S control messages on the RS422 master port at 9600 baud, 8, N, 1 .
Note: To control HNDR-S series DVR, the DVR firmware should be 1.0.17 or later.
(Tested firmware: HVBCPUX – 4.96x
www.asia.security.honeywell.com
Honeywell Video Systems
S1/7
S1/6
Valid
Valid
Function
Function
Off
Off
S2/7
S2/6
Address
Address
6
5
Off
Off
S3/7
S3/6
Slave
Master
Port
Port Baud
Baud
Off
On
S2/7
S2/6
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
On
On
HVBCFG – 3.08 (Build 32)
S1/5
S1/4
ASCII
Valid
string
Function
mode
Off
On
S2/5
S2/4
Address
Address
4
3
Off
Off
S3/5
S3/4
Master
Input
Port Baud
Type
Off
On
S2/5
S2/4
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
On
On
HVBPIT44 – 3.03)
11 December 2008
S1/3
S1/2
ASCII
ASCII
string
string
mode
mode
On
On
S2/3
S2/2
Address
Address
2
1
Off
Off
S3/3
S3/2
Input
Input
Type
Type
On
On
S2/3
S2/2
Off
Off
Off
On
Off
On
On
Off
On
Off
On
On
Rev 1.0
S1/1
ASCII
string
mode
On
S2/1
Address
0
Off
S3/1
Input
Type
Off
S2/1
On
Off
On
Off
On
On
1 of 5
Advertisement
Related Manuals for Honeywell HNDR-S 4848
Summary of Contents for Honeywell HNDR-S 4848
- Page 1 S2/3 S2/2 S2/1 Transmit Honeywell HNDR-S control messages on the RS422 master port at 9600 baud, 8, N, 1 . Note: To control HNDR-S series DVR, the DVR firmware should be 1.0.17 or later. (Tested firmware: HVBCPUX – 4.96x HVBCFG – 3.08 (Build 32) HVBPIT44 –...
-
Page 2: Hardware Configuration
HONEYWELL SECURITY TECHNICAL BULLETIN 11 December 2008 Hardware Configuration • Connect CPU RS422 Master Port to Slave Port of HVBPIT44. • Connect Master Port of HVBPIT44 to HNDR-S Com 2 (RS-485). CPU RS422 Master Port HVBPIT44 Slave Port Pin Number... -
Page 3: Device Configuration
3. Select the “Device Type” which is to be configured. 4. Click icon to browse “HNDR-S.db” which is locate in “C:\Program Files\Honeywell\VBloXCFG\DBF\” 5. Set “Com Port” to “1” if the control signal to the device is connected to the VideoBloX CPU master communications port. - Page 4 HONEYWELL SECURITY TECHNICAL BULLETIN 11 December 2008 HNDR-S 4848 DVR Configuration 1. Configure Communication port a. Push Menu button of DVR and enter the DVR setting menu. b. Move to System menu and select Serial Setup. c. Move to COM2 485 and select Keyboard HTX-3000 as below figure.
- Page 5 HONEYWELL SECURITY TECHNICAL BULLETIN 11 December 2008 HEGS5BLX Operation To select “HNDR-S 4848”, press “DVR” button. Then press “1” + “Enter” buttons to select DVR number 1. Joystick DVR Function Keys Item Function supported Description (The Keyboard should be in DVR mode for the below operation)