Viking E-30 Technical Practice page 2

I n s t a l l a t i o
I n s t a l l a t i o
IMPORTANT: Electronic devices are susceptible to lightning and power station electrical surges from both the AC outlet and the
!
telephone line. It is recommended that a surge protector be installed to protect against such surges. Contact Panamax at (800)
472-5555 or Electronic Specialists Inc. at (800) 225-4876.
Caution: When warm air comes in contact with cold surfaces, such as outside walls and conduits, it causes condensation. To prevent
condensation from accumulating inside the E-30 always bring conduit into the bottom of the unit. If this is not possible, drill a 1/4" diam-
eter hole in the bottom of the gray plastic box.
*Note: Peel off paper liner and adhere gasket to the back of the faceplate, centering it over the four corner mounting holes. Be careful
to position the modular jack inside the chassis as not to damage the components on the circuit board.
Front View of
Plastic Rough-In
Box (included)
Wire knock out
(2) Standard flat head dry wall
(sheet rock) screws (not included)
Important: The E-30 will NOT mount
to a standard double gang box.
Note: The plastic rough-in box (part # 259576) may be purchased separately
in advance. Go to www.vikingelectronics.com and click on "Spare Parts".
Analog
PABX/KSU
Station
C.O. Line
RJ11
or
* Note: To increase surge protection, loosen the PCB mounting screw labeled
from the mounting screw to Earth Ground (grounding rod, water pipe, etc.)
P r o g r a m m
P r o g r a m m
A. Accessing the Programming Mode
The E-30 phone can be programmed from any Touch Tone phone using a C.O. line, analog PABX/KSU station, or a
DLE-200B Line Simulator.
1. Using the Security Code
Step 1. Move DIP switch 2 to the ON position (sets unit to answer incoming calls - see section E).
Step 2. From a Touch Tone phone call the line attached to the E-30.
Step 3. When the E-30 answers, enter the 6-digit security code (factory set to 845464 - see section B). A double beep
should then be heard indicating you have entered the programming mode.
2. Without the Security Code
Step 1. Move DIP switch 2 to the ON position (sets unit to answer incoming calls - see section E).
Step 2. Move DIP switch 3 to OFF (incoming calls enter the programming mode without security code - see section E).
Step 3. From a Touch Tone phone call the line attached to the E-30.
Step 4. When the E-30 answers, a double beep will be heard and you will automatically enter the programming mode.
Step 5. When finished programming, move DIP switch 3 back to the ON position (see section E).
Note: If a valid memory position is entered, a double beep will be heard, four beeps indicate an error.
n
n
2.1"
*
Adhere gasket to front panel,
4.0"
centering over mounting holes
5.0"
Push to Call Button
Red Off-Hook LED Indicator
(4) 6-32 X 3/4" stainless steel, flat
head, hexdrive, screws (included)
Condensation Drain Hole
Rear View of a Standard
E-30 Phone
i n g
i n g
Need More Information on the DLE-200B?
?
Call (715) 386-4345 and select 605.
3.25"
5.22"
5.14"
Condensation
Drain Hole
Front View of Optional
2.25"
VE-5x5 (not included)
The optional VE-5x5 Surface Mount Box is designed
to be surface mounted to a single gang box, double
gang box or VE-GNP gooseneck pedestal (right).
Need More Information on VE-5x5 or VE-GNP?
?
Call (715) 386-4345 and select 424.
Analog
PABX/KSU
Station
C.O. Line
Spade
Terminal
(included)
* Earth Ground
(optional)
(as shown above) and fasten a wire with spade terminal (included)
(4) 0.38" diameter
(for gooseneck mounting)
(4) 0.2 x 0.43 slots
for double gang box
(2) 0.2 x 0.43 slots
for single gang box
(1) .74" dia 3.0" 3.3"
3.0"
Rear View of VE-5x5
(not included)
Rear View of an
E-30-EWP Phone
Gel-Filled
Butt
Connectors
(included)
Red
or
Green
E-30 shown with
Viking Model
VE-GNP
Gooseneck
Pedestal
Spade
Terminal
(included)
* Earth Ground
(optional)