Control Panel (Mixer Section) - Fostex FD-8 Owner's Manual

Control Panel (Mixer Section)

7
6
5
4
3
2
1
1. Input faders [1-8]
These faders allow you to control the input level of signals
selected via the INPUT SEL switch [2] (that is, the input
signals from the INPUT jacks or the recorder output signals).
Nominal level is obtained at fader position of 7-8, and the
fader achieves approximately 6dB of gain at the 10 position.
2. Input select switches [INPUT SEL (INPUT/OFF/TRK)]
These switches allow you to select signals to be routed to
the input faders. The following options are available:
"INPUT" Signals from instruments and microphones connected
to the INPUT jacks are routed to the channel faders.
"OFF" The switch is turned off. No signals are routed.
"TRK" Recorder output signals (TRK 1-8) are routed to the
channel faders, with Track 1 output routed to Channel 1,
Track 2 routed to channel 2, etc.
3. Panpot knobs [PAN (L/R)]
Panpot knobs have the following two functions:
AUX AUX AUX AUX
0 0 0 0
AUX1 AUX2 AUX1 AUX2 AUX1 AUX2 AUX1 AUX2
EQ EQ EQ EQ
HIGH 0 HIGH 0 HIGH 0 HIGH 0
- + - + - + - +
MID MID MID MID
GAIN 0 GAIN 0 GAIN 0 GAIN 0
- + - + - + - +
MID MID MID MID
SHIFT 900 SHIFT 900 SHIFT 900 SHIFT 900
300 300
2k 300 2k 300 2k
200 5k 200 5k
200 5k 200 5k
LOW LOW LOW LOW
0 0 0 0
- + - + - + - +
MON MON MON MON
0 0 0 0
INPUT TRK 1 INPUT TRK 2 INPUT TRK 3 INPUT TRK 4
PAN PAN PAN PAN
MON L MON R MON L MON R MON L MON R MON L MON R
PAN PAN PAN PAN
L R L R L R L R
INPUT SEL INPUT SEL INPUT SEL INPUT SEL
INPUT INPUT INPUT INPUT
OFF OFF OFF OFF
TRK 1 TRK 2 TRK 3 TRK 4
1 2 3 4
10 10 10 10
5 5 5 5
0 0 0 0
Letters in brackets ([ ]) are labels on the panel.
AUX AUX AUX
0 0 0
AUX1 AUX2 AUX1 AUX2 AUX1 AUX2
EQ EQ EQ
HIGH 0 HIGH 0 HIGH 0
- + - + - +
MID MID MID
GAIN 0 GAIN 0 GAIN 0
- + - + - +
MID MID MID
SHIFT 900 SHIFT 900 SHIFT 900
2k 300 2k 300 2k 300 2k
200 5k 200 5k 200 5k
LOW LOW LOW
0 0 0
- + - + - +
MON MON MON
0 0 0
INPUT TRK 5 INPUT TRK 6 INPUT TRK 7
PAN PAN PAN
MON L MON R MON L MON R MON L MON R
PAN PAN PAN
L R L R L R
INPUT SEL INPUT SEL INPUT SEL
INPUT INPUT INPUT
OFF OFF OFF
TRK 5 TRK 6 TRK 7
5 6 7
10 10 10
5 5 5
0 0 0
H
M
L
LEVEL
12
During recording, you can use them to pan channel signals of the
sound sources connected to the INPUT jacks to Tracks 1-8 .
Turn the knobs all the way to L or R. If you turn the knob to L, the
1
corresponding channel signal is recorded to Tracks 1 , 3 , 5 and 7.
If you turn the knob to R, the corresponding channel signal is
recorded to Tracks 2 , 4, 6 and 8.
For mixdown, use these knobs to determine the stereo image of
2
the playback sound of Tracks 1-8. Turn the knobs to the desired
position.
4. Monitor panpot knobs [PAN (MON L/MON R)]
These knobs allow you to adjust the balance of the signals
that were level-adjusted for the level via the MON knob [5]
before you send them to the monitor section L and R. The
following options are available.
"MON L" The signal routed to the MON knob will be sent only to
monitor section "L."
"Center" The signal routed to the MON knob will be sent to both
monitor section "R" and "L" at the same level.
"MON R" The signal routed to the MON knob will be sent only to
monitor section "R."
Names and Functions
AUX AUX RTN
0
AUX1 AUX2
EQ
HIGH 0 1
- + 0 10
MID
GAIN 0 2
- + 0 10
MID
SHIFT 900
300 2k
200 5k
LOW
0
- +
MON MON SECTION
0
INPUT TRK 8
MASTER
PAN
MON L MON R
0 10
PAN
L R
SELECTOR
INPUT SEL
INPUT L/R
OFF L/R+MON
TRK 8 MON
8 L/R
10 10
5 5
0 0
H
M
L
LEVEL
8
9
10
11
7