Advertisement
Advertisement
Related Manuals for Tannoy EYRIS
Summary of Contents for Tannoy EYRIS
- Page 1 E Y E C AT C H I N G S O U N D O W N E R ’ S M A N U A L...
-
Page 2: Table Of Contents
24hrs use. Once they have been further run- in over a longer period, there will be clear enhancement of the stereo imaging, mid-band quality and bass performance characteristics. We are confident that you will continue to enjoy your new Tannoy Eyris loudspeakers for many years to come. -
Page 3: Wideband™ Technology
TERMINAL PANEL (See fig. 2) In order to take advantage of the driver earthing feature within the Eyris range and to optimise performance further, use a shielded or screened loudspeaker cable. The screening termination should be connected to the earth or 'ground' (green) terminal on the loudspeaker and to the ground or earth connection on the amplifier. -
Page 4: Unpacking
WALL MOUNTED REAR CHANNEL SPEAKERS (See figs. 7 and 8) The Eyris rear speaker has a driver configuration optimised for a flat response at the listening position when wall mounted. It is supplied with an integrated wall hanging and signal cable linking system, utilising professional grade connectors, to provide maximum convenience and performance. -
Page 5: Installation
Viewed from the back the professional grade Dinkle plug for the Eyris rear speaker connection panel has clear polarity markings. The left hand pair of + and - terminals connect to the rear output terminals (+ and -) of your A/V amplifier. The right hand pair of + and - connectors on the Dinkle plug enable direct connection, in series, to an additional speaker. -
Page 6: Bi-Amping
POSITIONING AND FINE-TUNING (See fig. 9) To get best results from your new Tannoy Eyris loudspeakers it is worthwhile spending a little time finding the optimum set-up configuration. Begin by angling the speakers towards your chosen listening position, usually this is on the centre line of the room, so that when seated you can just see the inner side panel of each speaker. -
Page 7: Bass Tuning
'pan' from left to right and front to rear seamlessly. SCREENING The large magnet assemblies on the loudspeaker drive units of all Eyris models are fully screened to eliminate colour-fringing effects when mounted close to television monitors. -
Page 8: Centre Channel Speaker
The Eyris centre channel can be wired in single wire or bi-wire mode, (see figs. 3 and 4), bear in mind that connection should be made to the dedicated centre channel output on your A/V processor amplifier. -
Page 9: Set-Up Diagrams
SET-UP DIAGRAMS FIG. 1 UNPACKING FIG. 2 TERMINAL PANEL CONNECTIONS HIGH FREQUENCY HIGH FREQUENCY NEGATIVE(-) TERMINAL POSITIVE(+) TERMINAL LOW FREQUENCY POSITIVE(+) TERMINAL LOW FREQUENCY NEGATIVE(-) TERMINAL 'EARTH' OR 'GROUND' TERMINAL SINGLE WIRE MODE AND EARTH (GROUND) FIG. 3 LEAD CONNECTION TO RIGHT SPEAKER POWER AMPLIFIER... - Page 10 SET-UP DIAGRAMS BI-WIRE MODE AND EARTH (GROUND) FIG. 4 LEAD CONNECTION TO RIGHT SPEAKER TO 'GROUND' OR 'EARTH' CONNECTION POWER AMPLIFIER LINK WIRES REMOVED ON AMPLIFIER (OPTIONAL) BI-AMPING MODE AND EARTH (GROUND) FIG. 5 LEAD CONNECTION TO RIGHT SPEAKER HIGH FREQUENCY POWER AMPLIFIER LOW FREQUENCY POWER AMPLIFIER...
- Page 11 SET-UP DIAGRAMS FIG. 7 EYRIS REAR WALLMOUNT ENSURE CORRECT SELECTION OF SCREW AND FIXING FOR YOUR WALL SURFACE EYRIS REAR CONNECTION FIG. 8 BRACKET POWER AMPLIFIER POSITIONING RECOMMENDATIONS – POSITIONING RECOMMENDATIONS – FIG. 9 FIG. 10 TWO CHANNEL STEREO HOME CINEMA 0.5 METRE...
- Page 12 Tannoy Limited, Home Audio Division, Coatbridge, Scotland, ML5 4TF. Tel: +44 (0) 1236 420199 Fax: +44 (0) 1236 428230 e-mail: sales@tannoy.com Website: www.tannoy.com Tannoy/TGI North America Inc., Suite 1, 335 Gage Avenue, Kichener, Ontario, Canada N2M 5E1. Tel: (519) 745-1158 Fax: (519) 745-2364 e-mail: inquiries@tgina.com Website: www.tannoy.com...