American DJ TRIBAR Spot User Instructions page 5

TRIBAR Spot
adjusted between "FS.00" (flash off) to "FS.99" (fastest flash).
RGB Dimmer Mode:
1. Plug the fixture in and press the MODE button until "CoLr" is dis-
played, then press the SET UP button.
2. When "r.XXX" is displayed you are in Red dimming mode. Press the
UP and DOWN buttons to adjust intensity. Press the SET UP button
to move to the next color adjustment.
3. When "G.XXX" is displayed you are in Green dimming mode. Press
the UP and DOWN buttons to adjust intensity. Press the SET UP but-
ton to move to the next color adjustment.
4. When "b.XXX" is displayed you are in Blue dimming mode. Press the
UP and DOWN buttons to adjust intensity. Press the SET UP button
to move to the next color adjustment.
5. After you have adjusted the RGB colors to make your desired color
you can then activate strobing by pressing the SET UP button to
enter the Flash (strobe) mode.
6. "FS.XX" will be displayed, this is Flash mode. The Flash can be
adjusted between "FS.00" (flash off) to "FS.99" (fastest flash).
DMX Mode:
Operating through a DMX controller gives the user the freedom to create
their own programs tailored to their own individual needs. This function
also allows you to use your fixtures as spot lights. The TRIBAR Spot has
7 DMX modes: 3 Channel mode, 5 Channel mode, 6 Channel mode, 8
Channel mode, another 8 Channel mode, 11 Channel mode, and a 20
Channel mode. See pages 15-22 for each modes' DMX traits.
1. This function will allow you to control each individual fixture's traits
with a standard DMX 512 controller.
2. To run your fixture in DMX mode press the MODE button until
"d.XXX" is displayed. "XXX" represents the current displayed ad-
dress. Use the UP or DOWN buttons to select your desired DMX
address, then press the SETUP button to select your DMX Channel
mode.
3. Use the UP or DOWN buttons to scroll through the DMX Channel
modes. The Channel modes are listed below:
• To run the 3 Channel Mode, press the MODE button until "CH-1"
is displayed. This is the 3 Channel DMX Mode.
• To run the 5 Channel Mode, press the MODE button until "CH-2"
is displayed. This is the 5 Channel DMX Mode.
ADJ Products, LLC - www.adj.com - TRIBAR Spot User Manual Page 9
Operating Instructions TRIBAR Spot
• To run the 6 Channel Mode, press the MODE button until "CH-3"
is displayed. This is the 6 Channel DMX Mode.
• To run the 8 Channel Mode, press the MODE button until "CH-4"
is displayed. This is the 8 Channel DMX Mode.
• To run the other 8 Channel Mode, press the MODE button until
"CH-5" is displayed. This is the other 8 Channel DMX Mode.
• To run the 11 Channel Mode, press the MODE button until
"CH-6" is displayed. This is the 11 Channel DMX Mode.
• To run the 20 Channel Mode, press the MODE button until
"CH-7" is displayed. This is the 20 Channel DMX Mode.
4. Please see pages 15-22 for DMX values and traits.
5. After you have chosen your desired DMX Channel mode plug in
the fixture via the XLR connections to any standard DMX controller.
ADJ LED RC (Remote Control) On/Off:
This function is used to activate and deactivate the ADJ LED RC (sold
separately). When this function is activated you can control the fix-
ture using the ADJ LED RC. Please see page 11 for RFC controls and
functions.
1. Plug the fixture in and press the MODE button until "AUTO" is dis-
played.
2. Press the SET UP button until "Ir.XX" is displayed. "XX" represents
either "on" or "oF".
3. Press the UP or DOWN buttons to either activate the remote func-
tion (On) or deactivate it (Off).
ADJ Products, LLC - www.adj.com - TRIBAR Spot User Manual Page 10
Operating Instructions