Operating instructions Rotary ironer B 995 D en - GB To avoid the risk of accidents or damage to the appliance it is essential to read these instructions carefully before installing and using it for the first time. M.-Nr. 07 660 420...
Contents Guide to the appliance ..........4 Warning and Safety instructions .
Contents Cleaning the water reservoir ......... 30 Ironing cover .
Guide to the appliance a Temperature selector h Hanging bar b Emergency release i Feed-in table c Control panel j Roller d Release catch k Heater plate e Mains connection cable l Finger guard f Foot pedal m Water reservoir cap g Ironing table...
Guide to the appliance Control panel e Q "Steam" indicator light a Roller speed selector b "On-Off" I-0 indicator light C "Temperature" indicator light c "On-Off" button I-0 "Water reservoir empty" indicator light d Q "Steam" button...
Keep these instructions in a safe If the supply cord is damaged, it must be replaced by a Miele approved place and ensure that new users are service technician to avoid a hazard. familiar with the content. Pass them on to any future owner.
Wide sleeves, unforeseen dangers for the user, for apron straps, scarves and ties etc. which Miele cannot accept liability. could be taken in by the roller. Repairs should only be undertaken by a Miele approved service technician.
It is designed for hanging laundry on. Accessory parts may only be fitted After use it should be swung back out when expressly approved by Miele. If of the way. Take care not to press down spare parts or accessories from other on the bar when it is swung out.
Caring for the environment Disposal of the packing Disposal of your old appliance material or machine The transport and protective packing Electrical and electronic appliances / has been selected from materials which machines often contain materials are environmentally friendly for disposal which, if handled or disposed of and can normally be recycled.
Moving the ironer Safety Do not remove the safety device until the ironer has been set up on its rollers. ^ To remove it simply pull it off. Store it in a safe place for future use. It should be fitted to the ironer again before moving it (e.g.
Moving the ironer The ironer is fitted with four rollers. ^ Hold the ironing table securely and pull on the release catch situated at ^ Hold the ironer by the ironing table to the back of the ironing table on the push it or to pull it towards you.
Before using for the first time Dust cover Connection cable The mains connection cable is wound The dust cover which protects the roller round a hook underneath the ironing during transit has to be removed. table. ^ First remove the feed-in table by lifting it out of the right hand holder, Unwind the cable.
Before using for the first time Then insert the plug in the socket and switch the ironer on. The heater plate will rise automatically. ^ An adhesive label for the temperature selector (see illustration) is supplied separately. Please stick this around the temperature selector.
Before ironing Preparation of the working Preparing the laundry area Correct preparation of the laundry is essential for successful ironing. To ensure an even distrubution of steam make sure the ironer is level and Before ironing, the laundry should be: secure and that it cannot roll sideways.
Before ironing Checking the effectiveness of Pulling into shape and smoothing the finger guard Pull the dampened laundry into shape The finger guard is a safety feature and as usual. should always be checked before the ironer is used. Smooth out ties, straps, seams and hems.
Steam The ironer can also be used with steam Never use softened or distilled for ironing dry or slightly damp laundry. water on its own in this ironer as this will cause pitting corrosion in the Ironing with and without steam water reservoir.
Steam One reservoir is sufficient for approx. 40 minutes of ironing with steam. It takes approx. 4 minutes for the water to heat up to the correct temperature for steam ironing. The heating-up time may change as a result of limescale building up in the reservoir.
Ironing Switching on and off Material Dot symbol Temperature range ß Minimum iron / temperature Synthetics ßß Woollens / Medium Silks temperature ßßß Linen / High Cottons temperature 40 - 60°C The I-0 "On-Off" button is used for switching the ironer on and off. To switch on ^ Press the I-0 button in.
Ironing Select the temperature for ironing Switching the steam on and off (when ironing with steam) Set the temperature to ßßß, before ^ Turn the temperature selector to selecting steam. ßßß Linen / Cottons (high The Q "Steam" button is used for temperature).
Ironing Select the roller speed Ironing There are 5 roller speed settings, from The ironing process is controlled by the low (approx. 2 m/min) to high (approx. foot pedal which has three positions: 4.5 m/min). A low speed makes it easier to iron complicated articles such as shirts and blouses.
Ironing Feeding laundry in Removing the feed-in table ^ Arrange laundry along the feed-in The feed-in table can be removed when table so that it is straight and smooth. ironing shaped garments, e.g. skirts. ^ First lift it out of the right hand holder, ^ Then carefully turn the roller by hand and then pull it out to the left of the until the laundry makes contact with...
Ironing After ironing Useful tips ^ Switch the ironer off. If creases appear on items being ironed: ^ Switch off Q "Steam". Stop the roller and pull the item back ^ Set the temperature selector to I. slightly. Smooth it out and if necessary dampen it with a wet cloth.
Ironing Power cut In the event of a power cut activate the emergency release. If there is a power cut whilst you are ironing the heater plate will stay in contact with the roller. This traps the laundry with the danger of it singeing. To free the laundry: ^ Pull the emergency release catch upwards.
Ironing tips The following tips are intended as helpful suggestions to get you started. With practice you will probably find alternative ways of ironing which suit your style of working. Tea towels, hand towels, handkerchiefs, serviettes etc. Place on the ironing table with the straight grain of the fabric to the feed board.
Ironing tips Duvet covers Pillow cases ^ First do up poppers and buttons and feed this end through the ironer first. Then iron the whole pillow case from both sides. Shirts Remove the feed-in table for ironing shirts. Iron in the following order: ^ Sleeves and cuffs ^ First do up poppers and buttons.
Ironing tips Sleeves and cuffs Back / shoulder yoke ^ Pull sleeves smooth ready for ironing. Shirts with a shoulder yoke: Do not iron the cuff yet. ^ Fold the yoke along the back seam. ^ Iron the sleeves from the cuff seam to ^ Place the shirt side on to the roller the underarm seam.
Ironing tips Back Front Iron the back in two sections, from the The fronts are ironed in one pass middle to the side seams. together with the lower section of the back up to the armhole seam. ^ Start with the front left. ^ Pull the shirt over the roller as far as the yoke seam - or to the collar seam on shirts without a yoke - and smooth...
Ironing tips Collar Pyjamas Pyjamas tops should be ironed following instructions for shirts. Iron trouser legs on pyjamas separately. ^ Iron one leg from the front and the other from the back. ^ Iron from the top to the bottom. ^ Then pull into shape and iron to the waist.
Ironing tips Pressing trousers ^ Press each leg separately. Let the top of the trousers hang over the edge of the roller. ^ Cover with a damp cloth and turn the roller by hand until the trouser leg is covered by the heater plate. ^ Press to iron, then do the same to the other trouser leg.
Maintenance and care Cleaning the water reservoir Disconnect the ironer from the Limescale deposits in the water reservoir, electricity supply by switching off at caused by hard water, can cause the the wall socket and withdrawing the steam jets to become blocked. Should plug before any cleaning and this happen, the limescale deposits can maintenance work.
^ Undo the cords at each end of the unsightly, it can be replaced easily. roller cover. Replacement ironing covers are available from your Miele dealer or the Miele Spare Parts Department. ^ Unwind the cover.
Maintenance and care ^ Completely unwind the cotton ^ Insert the raw edge of the new undercloth attached to the roller and ironing cloth into the retaining slot let it hang down smoothly. with the wrong side down. Leave the cords hanging free and smooth out the cloth.
Maintenance and care ^ Switch on the ironer. After the roller has gone through three or four revolutions and the end of the When the ironer is switched on, the ironing cover is under the heater plate: heater plate heats up immediately. ^ Switch off the ironer while keeping The temperature selector must be the foot pedal pressed down.
Problem solving guide With the help of the following notes, minor faults in the performance of the machine, some of which may result from incorrect operation, can be put right without contacting the Service Department. Repair work to electrical appliances should only be carried out by a suitably qualified person in strict accordance with current local and national safety regulations.
Problem solving guide Problem Possible cause Remedy There is no steam. The water reservoir Fill the water reservoir. The Q "Steam" is empty. indicator light goes out during ironing and "Water reservoir empty" lights up red. The steam jets are Pure tap water has Empty and rinse out the water spitting.
After sales service In the event of a fault, please contact: N.B. A call-out charge will be – your Miele dealer or applied for unnecessary service – the nearest Miele Service visits where the problem could have Department, (see address on the been rectified as described in this back page).
Electrical connection Electrical connection U.K. Non-rewireable plugs BS 1363 All electrical work should be carried out The fuse cover must be refitted when by a suitably qualified and competent changing the fuse, and if the fuse cover person, in strict accordance with is lost, the plug must not be used until a current national and local safety suitable replacement is obtained.
Technical data Height 95.9 (folded up 105.2) cm Width 98.5 (folded up 50) cm Depth 38.0 cm Weight 39 kg max. load 382 Newton Water reservoir capacity 0.8 litres Voltage see data plate Rated load see data plate Fuse rating see data plate Test certificates awarded Radio/TV suppressed, VDE...
Alteration rights reserved/3009 M.-Nr. 07 660 420 / 00...