Download  Print this page

Honeywell AirAlert 96d Instruction And Installation Manual

Multi-channel gas monitoring system.
Hide thumbs

Advertisement

Manning
Manning
EC-F9-NH
AirAlert
Multi-Channel
Gas Monitoring System
Preliminary
Instruction and Installation Manual
Rev C
Manning AirAlert 96d
Honeywell Analytics
rd
11511 West 83
Terrace
Lenexa, Kansas 66214
800.444.9935 or 913.894.1185
Manning AirAlert-96d Gas Monitor
913.894.1296 fax
9138941296fax
TM
96d
3
Warn
Alarm
High Alarm
Power
Enter
ESC
Silence
Fault
TX
RX
sales@manningsystems.com
www.gasalarm.com
19073 AIRALERT96D 05/2006 Prelim REVC Copyright © 2006 Honeywell Analytics. All Rights Reserved.
19073 AIRALERT96D 5/2006 REVC
19072 ECF9NH3 4/2006 REVE
1

Advertisement

   Related Manuals for Honeywell AirAlert 96d

   Summary of Contents for Honeywell AirAlert 96d

  • Page 1 11511 West 83 Terrace Lenexa, Kansas 66214 sales@manningsystems.com 800.444.9935 or 913.894.1185 www.gasalarm.com Manning AirAlert-96d Gas Monitor 19073 AIRALERT96D 05/2006 Prelim REVC Copyright © 2006 Honeywell Analytics. All Rights Reserved. 913.894.1296 fax 19073 AIRALERT96D 5/2006 REVC 19072 ECF9NH3 4/2006 REVE 9138941296fax...
  • Page 2: Table Of Contents

    Title Page AirAlert Installation System Wiring Sample Network Wiring Power Wiring Communications Wiring Relay Outputs Datalogger User Interface AirAlert 96d-RMS Relay Module PCB Manning AirAlert-96d Gas Monitor 19073 AIRALERT96D 05/2006 Prelim REVC Copyright © 2006 Honeywell Analytics. All Rights Reserved.
  • Page 3: Introduction

    Alarm High Alarm Caution Power Enter Silence Fault To avoid possible personal injury: Warning: Substitution of components may • impair intrinsic safety. Manning AirAlert-96d Gas Monitor 19073 AIRALERT96D 05/2006 Prelim REVC Copyright © 2006 Honeywell Analytics. All Rights Reserved.
  • Page 4: Installation

    Warning A cable with more than one pair of wires is unacceptable for communication use. 5’ Manning AirAlert-96d Gas Monitor 19073 AIRALERT96D 05/2006 Prelim REVC Copyright © 2006 Honeywell Analytics. All Rights Reserved.
  • Page 5: Wiring

    Contact Honeywell Analytics for help with all power requirements. • Channel 4: Modbus output only — No sensor can be connected to Channel 4 Manning AirAlert-96d Gas Monitor 19073 AIRALERT96D 05/2006 Prelim REVC Copyright © 2006 Honeywell Analytics. All Rights Reserved.
  • Page 6: Sample Network Wiring

    Power cable; Two conductor, 14 AWG (Belden 5100UE) 4/20 mA comm cable; Three conductor, 18 AWG, shielded, stranded (Belden 8770) VL sensor cable; Four conductor, 16 AWG, non-shielded Manning AirAlert-96d Gas Monitor 19073 AIRALERT96D 05/2006 Prelim REVC Copyright © 2006 Honeywell Analytics. All Rights Reserved.
  • Page 7: A Power

    Channels 1-2-3: Modbus protocol — Communicates only with Modbus devices • Channel 4: Modbus output only — No sensor can be connected to Channel 4 Manning AirAlert-96d Gas Monitor 19073 AIRALERT96D 05/2006 Prelim REVC Copyright © 2006 Honeywell Analytics. All Rights Reserved.
  • Page 8: C Relay Outputs

    1-2-3-4 must alwaysbe in E.O.L. position Relay Outputs (J3-J7-J25-J26) 5A, 30 Vdc or 120 Vac (resistive load) Normally open Normally closed Manning AirAlert-96d Gas Monitor 19073 AIRALERT96D 05/2006 Prelim REVC Copyright © 2006 Honeywell Analytics. All Rights Reserved.
  • Page 9: Initial Startup

    9935)] and to modify exit the programming menu of AirAlert 96d the programming fields. or to cancel an input. (see latching option). Manning AirAlert-96d Gas Monitor 19073 AIRALERT96D 05/2006 Prelim REVC Copyright © 2006 Honeywell Analytics. All Rights Reserved.
  • Page 10: Operation

    By entering this mode, the user is able to analyse one sensor at a time. Only the displayed device is interrogated by the controller, thus has its information updated. Manning AirAlert-96d Gas Monitor 19073 AIRALERT96D 05/2006 Prelim REVC Copyright © 2006 Honeywell Analytics. All Rights Reserved.
  • Page 11: Programming Menus

    -COMM (no communication) Tx001 trgt: Ctrl -A (Warn) AD:03 -normal- 2006-02-11 Ref:#01 -B (Alarm) -C (High Alarm) Activated Relay Address Gas Concentration -Normal Manning AirAlert-96d Gas Monitor 19073 AIRALERT96D 05/2006 Prelim REVC Copyright © 2006 Honeywell Analytics. All Rights Reserved.
  • Page 12: Configuration

    The address then leaves the The DETECTION MENU does not appear for an editing mode and stops flashing. AirAlert 96d-RM8 relay module or AirAlert 96d-AP annunciator panel. Manning AirAlert-96d Gas Monitor 19073 AIRALERT96D 05/2006 Prelim REVC Copyright © 2006 Honeywell Analytics. All Rights Reserved.
  • Page 13 The MAX value is the level at which Alarm C (High Alarm) is activated (set). The MIN value is the level at which Alarm C (High Alarm) is deactivated (reset). Manning AirAlert-96d Gas Monitor 19073 AIRALERT96D 05/2006 Prelim REVC Copyright © 2006 Honeywell Analytics. All Rights Reserved.
  • Page 14 #XX (Activation of the component’s relay #XX) • Buzzer (Activation of the component’s audible alarm) • ALL (activation of all the component’s relays and audible alarm) Manning AirAlert-96d Gas Monitor 19073 AIRALERT96D 05/2006 Prelim REVC Copyright © 2006 Honeywell Analytics. All Rights Reserved.
  • Page 15: B Acquisition Mode

    Example of Threshold Log Mode Erase all events 2006-01-22 11:05:20;1;NH3;0;ppm;-normal-; 2006-01-22 11:06:02;1;NH3;12;ppm;-normal-; 2006-01-22 11:06:15;1;NH3;18;ppm;-normal-; 2006-01-22 11:06:28;1;NH3;6;ppm;-normal-; 2006-01-22 11:06:39;1;NH3;0;ppm;-normal-; 2006-01-22 11:30:45;1;NH3;15;ppm;-normal-; 2006-01-22 11:30:57;1;NH3;23;ppm;-normal-; 2006-01-22 11:31:08;1;NH3;20;ppm;-normal-; Manning AirAlert-96d Gas Monitor 19073 AIRALERT96D 05/2006 Prelim REVC Copyright © 2006 Honeywell Analytics. All Rights Reserved.
  • Page 16 #2 goes in alarm A and a few minutes later it’s the NH at address #3 that goes in alarm A. Manning AirAlert-96d Gas Monitor 19073 AIRALERT96D 05/2006 Prelim REVC Copyright © 2006 Honeywell Analytics. All Rights Reserved.
  • Page 17 Then, the existing ‘config.ini’ file is renamed ‘config.bak’, thus keeping a backup of the previous configuration; At last, a new ‘config.ini’ file with the current configuration is created. Manning AirAlert-96d Gas Monitor 19073 AIRALERT96D 05/2006 Prelim REVC Copyright © 2006 Honeywell Analytics. All Rights Reserved.
  • Page 18 Tx info to Tx info password in the second window. source tx001 target tx002 COPY Manning AirAlert-96d Gas Monitor 19073 AIRALERT96D 05/2006 Prelim REVC Copyright © 2006 Honeywell Analytics. All Rights Reserved.
  • Page 19 In the event of loss of power to the controller, relays will change states if set to failsafe mode. 6. Config Relay Configuration AP Brdcst: auto Manning Systems Manning AirAlert-96d Gas Monitor 19073 AIRALERT96D 05/2006 Prelim REVC Copyright © 2006 Honeywell Analytics. All Rights Reserved.
  • Page 20 The simulated gas concentration values are local to the controller. • Start with Tx00X (simulation starts with sensor 00X) • Confirm (simulation activation) Manning AirAlert-96d Gas Monitor 19073 AIRALERT96D 05/2006 Prelim REVC Copyright © 2006 Honeywell Analytics. All Rights Reserved.
  • Page 21: Specifications

    Keep an operation log of all maintenance, calibrations and alarm events. Manning AirAlert-96d Gas Monitor 19073 AIRALERT96D 05/2006 Prelim REVC Copyright © 2006 Honeywell Analytics. All Rights Reserved.
  • Page 22: Relay Module (optional)

    If the communication breaks down, that LED will turn off. Manning AirAlert-96d Gas Monitor 19073 AIRALERT96D 05/2006 Prelim REVC Copyright © 2006 Honeywell Analytics. All Rights Reserved.
  • Page 23: Relay Module Pcb

    From “A” terminal of controller to “A” terminal of next device From +24VDC terminal of power supply Normally closed From Ground terminal of power supply Manning AirAlert-96d Gas Monitor 19073 AIRALERT96D 05/2006 Prelim REVC Copyright © 2006 Honeywell Analytics. All Rights Reserved.
  • Page 24: Limited Warranty

    Manning AirAlert-96d Gas Monitor 19073 AIRALERT96D 05/2006 Prelim REVC Copyright © 2006 Honeywell Analytics. All Rights Reserved.

Comments to this Manuals

Symbols: 0
Latest comments: