Summary of Contents for ACR Electronics Cobham C406-1 Series
Page 1
C406-1 SERIES EMERGENCY LOCATOR TRANSMITTER Abbreviated Component Maintenance Manual This manual includes data for the equipment that follows: Component Part No. Model No. Emergency Locator Transmitter 453-5002 C406-1 Emergency Locator Transmitter 453-5003 C406-1HM Wulfsberg Electronics Division 6400 Wilkinson Rd., Prescott, AZ 86301...
Page 2
COBHAM AVIONICS WULFSBERG ELECTRONICS ABBREVIATED COMPONENT MAINTENANCE MANUAL C406-1 (453-5002), C406-1HM (453-5003) PROPRIETARY INFORMATION This document contains proprietary information and such information may not be disclosed to others for any purpose, nor used for manufacturing purposes without written permission from Wulfsberg Electronics. Information in this manual is subject to change without notice.
COBHAM AVIONICS WULFSBERG ELECTRONICS ABBREVIATED COMPONENT MAINTENANCE MANUAL C406-1 (453-5002), C406-1HM (453-5003) SERVICE BULLETIN LIST SERVICE ISSUE MANUAL MANUAL SUBJECT BULLETIN NO DATE REV NO REV DATE 25-62-10 Page 5 of 90 APR 06/10...
Page 6
COBHAM AVIONICS WULFSBERG ELECTRONICS ABBREVIATED COMPONENT MAINTENANCE MANUAL C406-1 (453-5002), C406-1HM (453-5003) THIS IS A BLANK PAGE 25-62-10 Page 6 of 90 APR 06/10...
Installation Registration Illustrated Parts List In the United States, the C406-1 Series ELT must be installed and maintained in accordance with the requirements herein and 14 CFR, FAR Parts 43, and 91; and other airworthiness requirements, as applicable. In Canada, the C406-1 Series ELT must be installed and maintained in accordance with the requirements herein and Canadian Aviation Regulations (CAR), Part V, Paragraph 551.104 and...
Page 16
ABBREVIATED COMPONENT MAINTENANCE MANUAL C406-1 (453-5002), C406-1HM (453-5003) C406-1 Series ELT installation and maintenance in all other countries must comply with the requirements herein and applicable national airworthiness requirements. The accessories (i.e., remote switch and antennas) addressed in this manual are the accessories most commonly associated with the C406-1 Series ELT.
COBHAM AVIONICS WULFSBERG ELECTRONICS ABBREVIATED COMPONENT MAINTENANCE MANUAL C406-1 (453-5002), C406-1HM (453-5003) TASK 25-62-10-990-802 2. Model Descriptions SUBTASK 25-62-10-990-001 C406-1 The C406-1 is a type AF (Automatic Fixed) ELT, which transmits on 121.5, 243.0, and 406 MHz. The ELT is enclosed within a multi-piece mounting frame consisting of a mounting tray, protective top cover and mounting frame cap.
LITHIUM BATTERY SAFETY CONCERNS INCLUDE THE POSSIBILITY OF FIRE, VENTING VIOLENTLY, AND VENTING OF TOXIC GASES. The lithium battery pack used on the C406-1 Series ELT is certified under TSO C142. NOTE: Details of TSO certification are available in the “452-0133 - 406 Lithium Battery Pack TSO C142 Report”...
SUBTASK 25-62-10-990-002 Discussion The 406 MHz transmitter frequency of the C406-1 Series ELT was originally 406.025 MHz. In order to comply with COSPAS-SARSAT frequency allocation requirements, changes to the 406 MHz frequency may occur since the original release of this product.
COBHAM AVIONICS WULFSBERG ELECTRONICS ABBREVIATED COMPONENT MAINTENANCE MANUAL C406-1 (453-5002), C406-1HM (453-5003) TASK 25-62-10-990-805 5. List of Acronyms, Abbreviations, and Definitions SUBTASK 25-62-10-990-001 Term Definition Advisory Circular – A Federal Aviation Administration (USA) bulletin with special information. For the purposes of this document, the acro- nym AC does not refer to electrical alternating current.
Page 22
COBHAM AVIONICS WULFSBERG ELECTRONICS ABBREVIATED COMPONENT MAINTENANCE MANUAL C406-1 (453-5002), C406-1HM (453-5003) EUROCAE European Organization for Civil Aviation Equipment – EUROCAE docu- ments are widely referenced as a means of compliance to European Technical Standard Orders (ETSOs) and other regulatory documents. Federal Aviation Administration –...
Page 23
COBHAM AVIONICS WULFSBERG ELECTRONICS ABBREVIATED COMPONENT MAINTENANCE MANUAL C406-1 (453-5002), C406-1HM (453-5003) Search and Rescue SCREEN ROOM The term “Screen Room”, within the context of this document, refers to a room designed to suppress RF signals, such that the broadcast of an ELT placed in the screen room cannot reach the SAR satellite sys- tem.
COBHAM AVIONICS WULFSBERG ELECTRONICS ABBREVIATED COMPONENT MAINTENANCE MANUAL C406-1 (453-5002), C406-1HM (453-5003) TASK 25-62-10-990-806 6. References SUBTASK 25-62-10-990-001 Regulatory Documents The following regulatory documents are referred to herein. When referring to such documents, it is the manual user’s responsibility to ensure they are using the latest revision or release of such documents.
The following documents are available on-line at the Artex web site at www.artex.net, or from Wulfsberg Electronics upon request. 570-1000, “ELT Test Set (ETS) Operation Manual” 570-4602, “ELT/NAV Interface Abbreviated Component Maintenance Manual” 572-0014, “C406-1 Series TSO Report” 572-0043, “452-0133 - 406 Lithium Battery Pack TSO C142 Report” 25-62-10 Page 25 of 90...
Page 26
COBHAM AVIONICS WULFSBERG ELECTRONICS ABBREVIATED COMPONENT MAINTENANCE MANUAL C406-1 (453-5002), C406-1HM (453-5003) THIS IS A BLANK PAGE 25-62-10 Page 26 of 90 APR 06/10...
COBHAM AVIONICS WULFSBERG ELECTRONICS ABBREVIATED COMPONENT MAINTENANCE MANUAL C406-1 (453-5002), C406-1HM (453-5003) DESCRIPTION AND OPERATION TASK 25-62-10-870-801 1. Description SUBTASK 25-62-10-870-001 Functional Overview The ELT automatically activates during a crash and transmits the standard sweep tone on 121.5 and 243.0 MHz. Approximately every 50 seconds, for up to 520 milliseconds (long message protocol), the 406 MHz transmitter turns on.
SUBTASK 25-62-10-870-002 Components The C406-1 Series ELT main assembly is housed in a high impact, fire resistant, polycarbonate plastic case, which is enclosed in a protective mounting frame assembly made of similar material. See "Figure 2. C406-1 Series ELT and Mounting Frame Assembly".
Buzzer". Figure 4. Buzzer The battery pack for the C406-1 Series ELT consists of four “D” size lithium manganese dioxide cells connected in series. To prevent the cells from being charged, diodes are connected across each cell and fuses are connected to the output. See "Figure 5. Battery Pack Assembly".
ABBREVIATED COMPONENT MAINTENANCE MANUAL C406-1 (453-5002), C406-1HM (453-5003) Two single-input rod and whip antennas are approved for use with the C406-1 Series ELT. Selection of the proper antenna is dependent upon end use, aircraft configuration and speed, and other factors. See "Figure 6. Rod and Whip Antennas".
Figure 8. ELT Operational Flow Diagram A primary feature of the C406-1 Series ELT is its simplicity of operation. As long as the ELT is connected to the remote switch harness ELT connector, such that pins 5 and 8 are jumpered (G-switch loop), it will activate in the event of a crash.
COBHAM AVIONICS WULFSBERG ELECTRONICS ABBREVIATED COMPONENT MAINTENANCE MANUAL C406-1 (453-5002), C406-1HM (453-5003) It is possible the primary G-switch or one of the auxiliary G-switches could activate the ELT in either a fixed or rotor wing aircraft as the result of severe maneuvers or a very hard landing.
TASK 25-62-10-870-803 3. Specifications SUBTASK 25-62-10-870-001 Environmental and Physical Table 2 lists the environmental and physical specifications of the C406-1 Series ELT. NOTE: For automatic activation, the higher threshold of 4.5 ft/sec (2.3 ) is specified in accordance with Eurocae ED-62. Use of the higher threshold crash sensor has been approved by the FAA as a deviation to TSO C126 (FAA Reference #98-130S-108, February 6, 1998).
COBHAM AVIONICS WULFSBERG ELECTRONICS ABBREVIATED COMPONENT MAINTENANCE MANUAL C406-1 (453-5002), C406-1HM (453-5003) SUBTASK 25-62-10-870-003 Antennas Table 4 lists the specifications of the antennas approved for use with the C406-1 Series ELT. Table 4. Antenna Specifications CHARACTERISTIC PARAMETERS 110-338 110-340 110-341...
Page 36
COBHAM AVIONICS WULFSBERG ELECTRONICS ABBREVIATED COMPONENT MAINTENANCE MANUAL C406-1 (453-5002), C406-1HM (453-5003) THIS IS A BLANK PAGE 25-62-10 Page 36 of 90 APR 06/10...
COBHAM AVIONICS WULFSBERG ELECTRONICS ABBREVIATED COMPONENT MAINTENANCE MANUAL C406-1 (453-5002), C406-1HM (453-5003) TEST AND FAULT ISOLATION TASK 25-62-10-750-801 1. Inspection and Test Regulatory Requirements SUBTASK 25-62-10-990-001 United States In accordance with FAR Part 91, Subpart C, § 91.207 (d), the ELT must be inspected within 12 calendar months after the last inspection for: Proper installation;...
COBHAM AVIONICS WULFSBERG ELECTRONICS ABBREVIATED COMPONENT MAINTENANCE MANUAL C406-1 (453-5002), C406-1HM (453-5003) SUBTASK 25-62-10-990-003 Other Countries For all other countries, maintenance and testing shall be conducted in accordance with the requirements of applicable national regulatory authorities and the requirements herein, as applicable.
COBHAM AVIONICS WULFSBERG ELECTRONICS ABBREVIATED COMPONENT MAINTENANCE MANUAL C406-1 (453-5002), C406-1HM (453-5003) TASK 25-62-10-750-802 2. Inspection and Test Procedures SUBTASK 25-62-10-990-001 Checklist Table 5 provides a list of the ELT inspection and testing requirements, a copy of which may be used as a checklist to verify inspection and test completion.
COBHAM AVIONICS WULFSBERG ELECTRONICS ABBREVIATED COMPONENT MAINTENANCE MANUAL C406-1 (453-5002), C406-1HM (453-5003) When the total of all known transmissions exceeds one hour; or On or before battery replacement (expiration) date. SUBTASK 25-62-10-750-001 G-Switch Functional Check – Item 4 CAUTION: A JUMPER IS REQUIRED TO PERFORM THIS CHECK. DUE TO THE POTENTIAL OF PHYSICAL DAMAGE IF THE JUMPER IS IMPROPERLY INSTALLED, THIS STEP SHOULD ONLY BE PERFORMED BY AN EXPERIENCED TECHNICIAN/MECHANIC.
COBHAM AVIONICS WULFSBERG ELECTRONICS ABBREVIATED COMPONENT MAINTENANCE MANUAL C406-1 (453-5002), C406-1HM (453-5003) Place the ELT in a container or screen room capable of substantially attenuating RF signals, or the transmitter power output shall be connected to a suitable dummy load to minimize radiation.
COBHAM AVIONICS WULFSBERG ELECTRONICS ABBREVIATED COMPONENT MAINTENANCE MANUAL C406-1 (453-5002), C406-1HM (453-5003) SUBTASK 25-62-10-750-005 121.5/243.0 MHz Power Output Measurement – Item 5c Connect the measuring device, referring to SUBTASK 25-62-10-750-002, on page 41. Activate the ELT, if necessary, by placing the control switch in the “ON” position. Wait three minutes.
COBHAM AVIONICS WULFSBERG ELECTRONICS ABBREVIATED COMPONENT MAINTENANCE MANUAL C406-1 (453-5002), C406-1HM (453-5003) SUBTASK 25-62-10-750-008 M. Current Draw Test – Item 5f CAUTION: EXERCISE EXTREME CAUTION TO AVOID CAUSING A SHORT CIRCUIT CONDITION, WHICH WILL BLOW THE FUSES IN THE BATTERY PACK. THIS TEST SHOULD ONLY BE PERFORMED BY AN EXPERIENCED TECHNICIAN/MECHANIC.
COBHAM AVIONICS WULFSBERG ELECTRONICS ABBREVIATED COMPONENT MAINTENANCE MANUAL C406-1 (453-5002), C406-1HM (453-5003) Allow the ELT to stabilize for at least 30 seconds to avoid false readings. Read the current draw on the ammeter. Steady state current draw must not exceed 200 mA. (10) Deactivate the ELT by placing the control switch in the “OFF”...
COBHAM AVIONICS WULFSBERG ELECTRONICS ABBREVIATED COMPONENT MAINTENANCE MANUAL C406-1 (453-5002), C406-1HM (453-5003) Repeat the activation and deactivation cycle if the ETS fails to read the message on the initial try. The 406 MHz oscillator may not be warmed up. If continued attempts to read the message fail, check for self-test error codes and refer to Table 6, on page 48.
COBHAM AVIONICS WULFSBERG ELECTRONICS ABBREVIATED COMPONENT MAINTENANCE MANUAL C406-1 (453-5002), C406-1HM (453-5003) SUBTASK 25-62-10-750-012 Antenna Test – Item 7 CAUTION: Do not allow the duration of this test to exceed 5 seconds. Tune a low quality AM receiver (i.e., radio) to 121.5 MHz. NOTE: The aircraft transceiver is not recommended for this test, because it is too sensitive to verify the integrity of the antenna system and it may pick up a weak signal even if...
COBHAM AVIONICS WULFSBERG ELECTRONICS ABBREVIATED COMPONENT MAINTENANCE MANUAL C406-1 (453-5002), C406-1HM (453-5003) TASK 25-62-10-810-801 3. Fault Isolation SUBTASK 25-62-10-810-001 Self-Test Error Troubleshooting Guidelines Table 6 describes the ELT self-test LED error codes (i.e., flash codes), their probable causes, and possible solutions. The 5-flash error is not present when the ELT is programmed with a serial user protocol (short message).
Page 49
COBHAM AVIONICS WULFSBERG ELECTRONICS ABBREVIATED COMPONENT MAINTENANCE MANUAL C406-1 (453-5002), C406-1HM (453-5003) CODE PROBABLE CAUSE POSSIBLE SOLUTION Battery low Low power output 3A fuse on battery pack circuit board faulty 3-Flash (cont.) Improper programming Verify 406 MHz programming Cannot be repaired in field - Return to Transmitter module faulty factory for servicing Indicates there is no navigation position data present...
COBHAM AVIONICS WULFSBERG ELECTRONICS ABBREVIATED COMPONENT MAINTENANCE MANUAL C406-1 (453-5002), C406-1HM (453-5003) TASK 25-62-10-050-801 2. Battery SUBTASK 25-62-10-050-001 Battery Pack Removal CAUTION: THE BATTERY PACK CONTAINS ELECTROSTATIC DISCHARGE SENSITIVE (ESD) COMPONENTS AND IT MUST BE HANDLED WITH CARE. IF POSSIBLE, WEAR A GROUNDED WRIST STRAP WHEN HANDLING THE BATTERY PACK DURING INSTALLATION ACTIVITIES.
COBHAM AVIONICS WULFSBERG ELECTRONICS ABBREVIATED COMPONENT MAINTENANCE MANUAL C406-1 (453-5002), C406-1HM (453-5003) TASK 25-62-10-500-801 3. Material or Equipment Return SUBTASK 25-62-10-510-001 Shipment Information If any material or equipment is to be returned to the factory, under warranty or otherwise, Wulfsberg Electronics must be notified prior to shipment with the following information: •...
Page 54
COBHAM AVIONICS WULFSBERG ELECTRONICS ABBREVIATED COMPONENT MAINTENANCE MANUAL C406-1 (453-5002), C406-1HM (453-5003) THIS IS A BLANK PAGE 25-62-10 Page 54 of 90 APR 06/10...
COBHAM AVIONICS WULFSBERG ELECTRONICS ABBREVIATED COMPONENT MAINTENANCE MANUAL C406-1 (453-5002), C406-1HM (453-5003) INSTALLATION TASK 25-62-10-410-801 1. Regulatory Requirements and Guidelines SUBTASK 25-62-10-990-001 TSO C126, Paragraph D TSO approval of the ELT does not constitute installation approval. All ELT installations are subject to field approval for a given airframe by either an approved FAA DER or FAA FSDO.
COBHAM AVIONICS WULFSBERG ELECTRONICS ABBREVIATED COMPONENT MAINTENANCE MANUAL C406-1 (453-5002), C406-1HM (453-5003) SUBTASK 25-62-10-990-005 RTCA DO-204, § 3.1.8 guidelines for mounting a ELT: The ELT shall be mounted to primary aircraft load carrying structures, such as trusses, bulkheads, longerons, spars, or floor beams. The mounts shall have a maximum static local deflection no greater than 0.1 inches (2.5 mm) when a force of 100 lbs (450 newtons) is applied to the mount in the most flexible direction.
STRUCTURAL INTEGRITY OF THESE COMPONENTS. THESE SAME CHEMICAL AGENTS MAY ALSO CAUSE CORROSION OF ELECTRICAL CONNECTIONS. Select a suitable location for the mounting tray. See "Figure 14. C406-1 Series ELT Outline and Dimensions". Refer to these dimensions when determining mounting location.
Refer to TASK 25-62-10-410-803, on page 78, for guidelines on ELT orientation in a helicopter. Mark the four holes needed for mounting the tray, using the tray as a pattern. The hole pattern is also illustrated in "Figure 14. C406-1 Series ELT Outline and Dimensions”, on page 57. 25-62-10...
Page 59
COBHAM AVIONICS WULFSBERG ELECTRONICS ABBREVIATED COMPONENT MAINTENANCE MANUAL C406-1 (453-5002), C406-1HM (453-5003) Drill the four mounting holes with a #19 or 4.25 mm drill. Install the mounting tray with the 8-32 x 5/8” SS pan head phillips screws, flat washers, lock washers, and nuts provided in the installation kit (455-7421), as shown in "Figure 15.
SUBTASK 25-62-10-990-001 Selection Use only antennas approved for use with the C406-1 Series ELT. The ELT will not work properly without being connected to an antenna for which it was designed. Verify the antenna selected matches the requirements of the specific installation.
COBHAM AVIONICS WULFSBERG ELECTRONICS ABBREVIATED COMPONENT MAINTENANCE MANUAL C406-1 (453-5002), C406-1HM (453-5003) TASK 25-62-10-450-803 4. Remote Switch SUBTASK 25-62-10-450-001 Location NOTE: This procedure is applicable to the most commonly used remote switch (345-6196-04). If an optional switch is installed in lieu of this one, the applicable installation instructions should be consulted.
COBHAM AVIONICS WULFSBERG ELECTRONICS ABBREVIATED COMPONENT MAINTENANCE MANUAL C406-1 (453-5002), C406-1HM (453-5003) TASK 25-62-10-450-804 5. Buzzer SUBTASK 25-62-10-450-001 Location CAUTION: PLACING THE BUZZER IN THE COCKPIT IS NOT RECOMMENDED DUE TO THE POTENTIAL FOR DISTRACTION. THE BUZZER PRODUCES A LOUD, SIREN-TYPE SOUND WHEN THE ELT IS ACTIVATED.
COBHAM AVIONICS WULFSBERG ELECTRONICS ABBREVIATED COMPONENT MAINTENANCE MANUAL C406-1 (453-5002), C406-1HM (453-5003) TASK 25-62-10-450-805 6. Wiring SUBTASK 25-62-10-990-001 General Considerations and Recommendations CAUTION: IF GROUND OR OTHER CONNECTIONS ARE BROKEN OR OTHERWISE DAMAGED, THE ELT IS STILL CAPABLE OF AUTOMATIC ACTIVATION; HOWEVER, THE COCKPIT REMOTE SWITCH MAY BE INCAPABLE OF RESETTING THE ELT AND OPERATION MAY NOT BE INDICATED ON THE REMOTE SWITCH LED.
COBHAM AVIONICS WULFSBERG ELECTRONICS ABBREVIATED COMPONENT MAINTENANCE MANUAL C406-1 (453-5002), C406-1HM (453-5003) Fabricate another ground wire long enough to reach from Pin 9 of the remote switch plug to aircraft ground. Fabricate a power wire long enough to reach from the remote switch plug (Pin 1 or Pin 3) to the selected aircraft power source.
COBHAM AVIONICS WULFSBERG ELECTRONICS ABBREVIATED COMPONENT MAINTENANCE MANUAL C406-1 (453-5002), C406-1HM (453-5003) Crimp an appropriately sized ring terminal on the remote switch power source wire end. NOTE: If desired, the power wire may be spliced to a power source in a manner acceptable to the aircraft manufacturer, or as described in AC 43.13-1, Paragraph 11-167.
COBHAM AVIONICS WULFSBERG ELECTRONICS ABBREVIATED COMPONENT MAINTENANCE MANUAL C406-1 (453-5002), C406-1HM (453-5003) Insert the buzzer power and ground wires in Pin 2 (+) and Pin 4 (–) of the receptacle, respectively. 12-PIN MOLEX NOTE: FEED THE WIRE BUNDLE THROUGH THE MOUNTING RECEPTACLE FRAME CAP HOLE PRIOR TO INSERTING THE PINS INTO THE RECEPTACLE...
COBHAM AVIONICS WULFSBERG ELECTRONICS ABBREVIATED COMPONENT MAINTENANCE MANUAL C406-1 (453-5002), C406-1HM (453-5003) SUBTASK 25-62-10-450-004 Wiring Installation Route the remote switch harness wire bundle and breakout wiring through the airframe. Route the antenna coax cable through the airframe. NOTE: A longer coax cable, up to 20 feet (6.1 m), may be fabricated if the cable provided is too short.
COBHAM AVIONICS WULFSBERG ELECTRONICS ABBREVIATED COMPONENT MAINTENANCE MANUAL C406-1 (453-5002), C406-1HM (453-5003) SUBTASK 25-62-10-450-008 Airframe Ground Connections Connect the ground wires to the airframe in accordance with the aircraft manufacturer’s written instructions or as described in AC 43.13-1, Chapter 11, § 15. See "Figure 21. Remote Switch Harness Wiring Diagram”, on page 67.
COBHAM AVIONICS WULFSBERG ELECTRONICS ABBREVIATED COMPONENT MAINTENANCE MANUAL C406-1 (453-5002), C406-1HM (453-5003) (11) Secure the mounting frame cap to the mounting tray with the thumbscrews and tighten them to no more than 18 lb-in (203 N•cm). (12) Tie up excess slack in the harness and coax cable, such that they form drip loops and there is enough slack, approximately 5 in.
COBHAM AVIONICS WULFSBERG ELECTRONICS ABBREVIATED COMPONENT MAINTENANCE MANUAL C406-1 (453-5002), C406-1HM (453-5003) SUBTASK 25-62-10-410-002 Installation Documentation Make appropriate logbook (i.e., aircraft records) entries and submit FAA Form 337, along with any supporting data required by the FAA for approval of the installation, as applicable. NOTE: Refer to TASK 25-62-10-410-801, on page 55, for additional information on installation approvals.
COBHAM AVIONICS WULFSBERG ELECTRONICS ABBREVIATED COMPONENT MAINTENANCE MANUAL C406-1 (453-5002), C406-1HM (453-5003) Reset the ELT by toggling the ELT local control switch to “ON” and back to “OFF” after 1-2 seconds. NOTE: This step is necessary because the ELT will occasionally activate when power is connected to it in Step 6.
COBHAM AVIONICS WULFSBERG ELECTRONICS ABBREVIATED COMPONENT MAINTENANCE MANUAL C406-1 (453-5002), C406-1HM (453-5003) SUBTASK 25-62-10-450-002 New Battery Installation CAUTION: DO NOT USE CONTACT CLEANER ON ELT COMPONENTS. SUCH CHEMICAL AGENTS CAN BE HIGHLY DESTRUCTIVE TO THE MOUNTING HARDWARE AND ELT HOUSING, CAUSING CRACKING, FRACTURING AND OTHER DAMAGE.
COBHAM AVIONICS WULFSBERG ELECTRONICS ABBREVIATED COMPONENT MAINTENANCE MANUAL C406-1 (453-5002), C406-1HM (453-5003) TASK 25-62-10-410-803 9. Helicopter Installations - Special Considerations SUBTASK 25-62-10-990-001 Background There are few guidelines, aside from experience, regarding the best way to mount an ELT in helicopters. Before the availability of multi-axis G-switch modules, manufacturers advised installing ELTs with the sensitive axis pointing approximately 45°...
COBHAM AVIONICS WULFSBERG ELECTRONICS ABBREVIATED COMPONENT MAINTENANCE MANUAL C406-1 (453-5002), C406-1HM (453-5003) SUBTASK 25-62-10-410-001 Orientation Mount the C406-1HM ELT parallel to the waterline of the fuselage, along the longitudinal axis, with the direction-of-flight arrow on the ELT pointing forward. See "Figure 27. Orientation of ELT for Helicopter Installations".
Page 80
COBHAM AVIONICS WULFSBERG ELECTRONICS ABBREVIATED COMPONENT MAINTENANCE MANUAL C406-1 (453-5002), C406-1HM (453-5003) THIS IS A BLANK PAGE 25-62-10 Page 80 of 90 APR 06/10...
COBHAM AVIONICS WULFSBERG ELECTRONICS ABBREVIATED COMPONENT MAINTENANCE MANUAL C406-1 (453-5002), C406-1HM (453-5003) APPENDIX A – ELT REGISTRATION TASK 25-62-10-990-801 1. Background Information SUBTASK 25-62-10-990-001 Hex ID Code Each 406 MHz ELT is programmed with a unique hex ID code (i.e., registration code) that is transmitted to the SAR satellite system.
COBHAM AVIONICS WULFSBERG ELECTRONICS ABBREVIATED COMPONENT MAINTENANCE MANUAL C406-1 (453-5002), C406-1HM (453-5003) TASK 25-62-10-990-802 2. Registration SUBTASK 25-62-10-990-001 Responsibility It is the responsibility of the aircraft owner to register the ELT. If an ELT is moved to a different aircraft (i.e., an aircraft other than the one it was originally installed on), and/or the aircraft is registered in a new country, the ELT must be re-registered.
Purpose This illustrated parts list (IPL) illustrates and lists the spare parts, with attaching hardware, applicable to the C406-1 Series ELT. Parts and components not listed herein, are not field replaceable and ELT repairs requiring parts outside the scope of this manual must be accomplished by the manufacturer.
COBHAM AVIONICS WULFSBERG ELECTRONICS ABBREVIATED COMPONENT MAINTENANCE MANUAL C406-1 (453-5002), C406-1HM (453-5003) TASK 25-62-10-990-802 2. Manufacturer Name and Address SUBTASK 25-62-10-990-001 Ordering Information Approved spare parts and battery packs may be ordered from Artex Aircraft Supplies, Inc., or any authorized dealer. CONTACT INFORMATION Sales, Wulfsberg Electronics 6400 Wilkinson Dr.
COBHAM AVIONICS WULFSBERG ELECTRONICS ABBREVIATED COMPONENT MAINTENANCE MANUAL C406-1 (453-5002), C406-1HM (453-5003) TASK 25-62-10-990-803 3. Explanation of Detailed Parts List Entries SUBTASK 25-62-10-990-001 Fig # & Item Column The first number at the top of the column is the figure number of the corresponding illustration.
COBHAM AVIONICS WULFSBERG ELECTRONICS ABBREVIATED COMPONENT MAINTENANCE MANUAL C406-1 (453-5002), C406-1HM (453-5003) Assemblies, subassemblies, and detail parts subject to modification, deletion, addition, or replacement by an issued service bulletin, are annotated to indicate both pre- and post- service bulletin configurations. The term (PRE SB XXXX) in the “Nomenclature” column designates the original configuration, and the term (POST SB XXXX) identifies assemblies and parts after the modification has been completed.