Advertisement
Quick Links
Download this manual
See also:
Operating Manual
Quick Setup Guide
Inkjet Fax UX-B800
3
Attach the trays.
Attach the received
document tray
1. Plug the power cord into a 230-240 V earthed
5
(3-prong) AC outlet.
Install the Print Cartridge.
6
1. Open the operation
panel.
5. Close the cover, pressing
firmly on both front corners.
CHANGE CARTRIDGE
Display:
1=NEW, 2=OLD
Setup for Scan to E-mail
7
To use Scan to E-mail you
must:
1. Have an Internet
connection
2. Have a router, hub, or
switch through which the
machine can be connected
to the Internet.
1
1. Open the cover (➊) and
remove the tape and
plastic strip (➋).
Attach the document
exit tray and flip out
the extension
Pull the received document tray
extension all the way out
2. Remove only the tape from the new cartridge.
IMPORTANT: Make sure all tape is removed.
Caution! Do not touch
the gold contact area.
6. a. Press
to select NEW.
b. Press
.
The machine will print an alignment
page.
The machine requires an IP address to communicate. Most
networks assign an IP address automatically when a device is
connected.
Connect one end of
an Ethernet cable
If your network requires that a permanent IP address be
(not included)* to the
assigned to the machine, see page 26 of the manual.
LAN port on the
machine, and the
To use Scan-to-E-mail, you must configure the "Sender
other end to a LAN
Address", and "SMTP Server" settings (see pages 18 - 20 of the
port on your router,
manual). You must also configure the "SMTP Authentication"
switch, or hub.
setting if required by your Internet service provider. This can be
done in the machine's Web page. First press the keys on the
*Please purchase a
machine as follows to check the IP address of the machine
straight-through
(page 16 of the manual).
(regular) Ethernet
FUNCTION
1. Press
cable that supports
10Base-T.
2. Press
3. Press
display.
2. Close the print
compartment cover.
(Do not install the print
cartridge yet.)
2
1
4
Load paper.
Fan the paper, and
tap the edges against
Attach the
a flat surface to even
paper tray
the stack.
2. Connect the phone line cord to the TEL. LINE socket and a wall
telephone socket (use the provided adapter if needed).
3. Make sure the cartridge holder is in
the position shown. Place your
fingers on top of the holder and open
the holder release.
7. In the alignment page,
locate the line that is
closest to a completely
straight line. Enter the
number of that line.
Example:
(To clear a mistake,
press
.)
, then
until [NETWORK SETTING] appears.
, then
to show [NETWORK INFORMATION].
. The address will appear on the bottom line of the
2
Connect the handset.
The stack should not
be higher than this line
4. Insert the new print cartridge (➊).
Close the holder (➋), making
sure it clicks into place.
1
8. Press
In this example, "15" is
closest to a straight line
Open the browser on a computer connected to the
same network as the machine, and type in the
machine's IP address in the Address bar of the
browser. The machine's Web page will open.
Select "E-mail Setup" in the menu frame and
configure the settings. For detailed information on
each setting, click "Help" in the menu frame.
If you don't know the information that must be
entered in each setting, ask your Internet service
provider.
Example:
Pull the paper
plate forward and
insert the paper
print side up.
The machine is
initially set for tone
dialing. If you are
on a pulse dial
line, change the
"DIAL MODE"
setting as
explained on
pages 48 and 49
of the manual.
2
.
Note: To enter your
name and fax number
and set the date and
time so that they
appear at the top of
each fax page you
send, see pages 14 -
15 of the manual.
(TCADH3939XHZZ)
Advertisement
