Commercial Mode Setup - LG Zenith HCS5610 Installation And Operating Manual

Commercial Mode Setup

This page provides an overview of the TV configuration. See the pages listed below for more
specific, detailed instructions at each step; how to access and use the Installer menu etc.
*Note1: Disconnect all Aux inputs. Under certain conditions, Auto Program
(Channel search) is disabled if there is an Aux input active.
*Note2: Under certain conditions, changes to the input mode of the RGB
inputs will not take effect until the power is cycled (TV is turned Off and On).
To avoid confusion, disconnect all RGB inputs before entering the Installer
menu.
Overview: Commercial Mode Setup Procedure
1.Set Installer Menu Items
(Enter Installer Menu, see page 53 for detailed instructions.)
a. Set Installer menu item 117 FACT DEFAULT, to 001 and press ENTER.
(This clears all installer menu items, custom settings, channel labels/icons
and reloads the factory default settings.)
b. Set Item 003 BAND/AFC.
- Broadcast: set to 000.
- CATV: set to 001.
c. Set item 028 CH OVERIDE to 001. This allows access to Auto Program,
Channel Labels and Channel List options in the Channel Menu.
d. Set other particular installer items that affect your TV programming
network. See pages 53 - 58.
e. After all required installer menu item settings have been adjusted, press
ENTER on the remote to remove Installer Menu.
2.Set Up TV Features
(See Picture, Sound, Setup menus etc. See TV Clonable options list on
page 59.)
*Note: Digital Font options are only available after a channel search has
been run and when the TV is tuned to an active digital channel with digital
captions.
3.Run Auto Program
(Search for all available channels.) Go to the Channel menu and access
the Auto Program option, follow on-screen instructions.
a. Edit Channel Scan. In the Channel Menu, access the Channel List menu.
• Delete channels per your system requirements: do you want to delete any
free channels so the guest cannot access them?
• Add familiar Channel Icons like ABC, CBS, NBC etc. to the channel
onscreen display. Add identifiable labels for the end user to readily know
what common networks are available. In the Channel menu, select the
Channel Label option, follow instructions on the bottom of the screen.
Verify TV Setup
At this point, verify that the channel lineup, channel icons and custom
labels are correct. Make sure the TV features are set per your requirements.
4. Transfer TV Setup to Controller Box: 2-5-5 + Menu
After the TV channel scan has been edited and channel label icons added,
enter the Installer menu. Once in the Installer menu, press 2-5-5 and MENU
on the remote. This transfers the TV setup to the internal controller box.
*Note: Only do 2-5-5 + MENU once or TV setup may be corrupted.
TV scans available channels and exits menu when transfer to controller is com-
plete.
5. Perform Adding Custom Channel Labels: 2-5-4 + Menu Mode
Enter Installer menu, press 2-5-4 and Menu. Add your own custom labels to
the channel on-screen displays. (See page 60.) To remove menu press MENU.
*Note: 2-5-4 + MENU can be performed more than once.
Lock Channel Scan
Set item 028 CH OVERIDE to 000 to lock the channel scan. After the
preceding has been completed, the Master TV setup is ready to be copied to
the LT2002 Clone Programmer, see next page.
- HRC: set to 002
- IRC: set to 003
HCS5610XX PTC INSTALLER MENU
000 INSTALLER SEQ
UPN 000-000-000-000 FPGA 09F1
PTC V1.00.000 CPU V1.01.00
TV/STB Installer Menu
117 FACT DEFAULT
003 BAND/AFC
028 CH.OVERIDE
073 CH. NOT AVBLE
TV/STB Installer Menu Items
RJP (Remote Jack Pack) TV/STB Setup
093 RJP AVAILABLE
• RJP Available? If you will use an RJP in
your system set Installer item 093 to 001.
DIGITAL 19-3 ANALOG 2
MONO STEREO SAP
WXYZ
MONO
WXYZ
Custom Channel Label 'WXYZ' created in
2-5-4 + Menu Add Channel Label Mode
028 CH. OVERIDE
After TV setup has been verified,
set item 028 Ch Overide back to 000.
000
00X
00X
001
001
001
000
P A G E 4 9