Roland V- HD-3 Setup Manual

HD-3 V-Drums Lite

Setup Guide

Check the Included Items
01
… Stand … HD-3 Sound Module
Attach the Foot Pipes
02
* When assembling the stand, take care that it does not fall over.
* When attaching the foot pipes, take care not to pinch your finger between
the movable parts or between the foot pipes and the floor.
1.
Lay the stand on the floor, and attach one of the foot pipes.
* Do not insert your fingers or hands underneath the pedals or in the spring.
* Be careful that the left and right foot pipes are located correctly.
Align the flat portion.
Align with the screw
holes.
Insert the screws
from the underside
of the stand, and
fasten them evenly
and securely.
2.
Flip the stand over, and attach the other foot pipe.
3.
Use the clamp to fasten the pedal cable.
4.
Set the stand upright.
* Make sure the foot pipes are securely fastened to the
stand. If not you risk to damage the stand or have
stability problems.
Attach the Sound Module
05
2.
1. Place the HD-3 sound
module on the holder.
holder
Connect the Cables
06
1.
Connect the cables to the pads and pedals.
The labels affixed to the
cables indicate the pad
CR
to which they should
be connected. Make
connections as shown in
T1
the illustration.
HH
SNR
* Connect T3 after you've finished
the step "08 Adjusting Pads
and Seat Height. "
HHC
Correct any Instability
07
If the stand wobbles because the
floor is not perfectly flat, use the
adjusters (three locations) to adjust
the height. In particular, when using
the HD-3 on carpet, adjust these so
that they are in firm contact with the
floor.
* Be careful not to pinch your
fingers or hands when making
these adjustments.
As soon as you open the package, check to see that all items are included. If anything is missing, please contact your dealer.
… Cymbal Pad x 3 … Foot Pipes
03
04
3.
Fasten it using the supplied Connect the D-sub cable
thumbscrews (two places). to the sound module, and
hand-tighten the screws (two
* Vibration can cause the screws to be
loosened. Should this occur, make locations).
sure to retighten them.
2.
Use the clamp to fasten the cymbal cable.
RD
T2
T3
Allow some slack
Fasten the cable
with the clamp
KIK
1. 2.
For either the left pedal or If the stand's vertical support
right pedal, turn the adjuster is still floating even after
clockwise (as seen from above) you've adjusted the left and
for the pedal that's not in firm right height, turn the rear
contact with the floor. adjuster.
Copyright © 2011 ROLAND CORPORATION
All rights reserved. No part of this publication may be reproduced in any form without the written permission of ROLAND CORPORATION.
Roland, V-Drums, V-Drums, Lite are either registered trademarks or trademarks of Roland Corporation in the United States and/or other countries.
Before using this unit, carefully read the sections entitled: "USING THE UNIT SAFELY" and "IMPORTANT NOTES. " These sections provide important
information concerning the proper operation of the unit. Additionally, in order to feel assured that you have gained a good grasp of every feature
provided by your new unit, Owner's manual and Setup Guide should be read in its entirety. The manual should be saved and kept on hand as a
convenient reference.
HD-3 parts
… AC Adaptor … Thumb Screw for
… Power Cord Sound Module x 2
Open the Arms
* Be careful not to pinch yourself.
1. Open the arm pipes in the order shown in the 2.
illustration (1, 2, 3, 4).
Rear of the HD-3
1
2
3
Tighten
4
Loosen
Attach the Pads
1.
Attach the cymbal pad. * For details on setup for left-handed use, refer to p.21 of the Owner's Manual.
Cymbal Knob
Tighten to obtain an appropriate amount of sway.
If this knob is too loose, you may experience double
triggering.
Adjusting Pads and Seat Height
08
1.
Seat Height
Adjust the height of the seat so that when
your feet are on the pedals, your legs are
parallel to the floor, as shown in the diagram.
Connect the AC Adaptor and Amp
09
* To prevent malfunction and/or damage to speakers or other devices, always turn down the volume, and turn off
the power on all devices before making any connections.
This completes assembly and connections.
■ When you've finished making connections, turn on the power as described in the HD-3 Owner's Manual, and
verify that you can hear sound.
When using the HD-3, you must firmly tighten the knobs and screws. In particular, before performing, you should check to be
sure that all knobs and screws are firmly tightened. If they are not tight, not only will you be unable to perform correctly, but your
equipment or pads may fall down.
… Screw for Foot … Drum Key
Pipe x 4
Using a drum key, loosen the screws of the cymbal 3.
arm holders.
Rod
4.
Cymbal Felt
Unscrew the cymbal knob,
mount the cymbal pad, and
attach the cymbal knob as
shown in the illustration.
Attach in the orientation
shown in the illustration.
2.
Adjust the height of the pad.
Adjust the height and position of each pad so you can play comfortably.
Once you've got everything adjusted the way you want it, firmly tighten
all the screws and knobs.
Adjust the height of the snare and its position
relative to other things, so it is suitable for the
height of your waist when you are seated, and
the position of the stool.
If you loosen the knob, you'll be able to move it
forwards or backwards.
knob
Audio Cable
AC Adaptor
Headphones
Monitor Amplifier etc.
* 5 1 0 0 0 2 3 4 9 4 - 0 2 *
Manual Set
… Setup Guide
… Owner's Manual
… Cable Tie
… Audio Cable
Adjust the rod height.
Adjust this so that it does not interfere with other pads,
taking care that the rod does not come out.
* As the cymbal rod sticks through the pipe on the
bottom side, be careful to not injure yourself
Tighten the bolt to fasten securely.
Set Tom 2 at the same height as Tom 1.
Tom 1 Tom 2
Be careful that the cable does not protrude.
Tighten the knob firmly.
If you use a drum key to loosen the screw of a tom,
you'll be able to move it to the left or right.
Place the AC adaptor so the side with the indicator
(see illustration) faces upwards and the side with
textual information faces downwards.
The indicator will light when you plug the AC
adaptor into an AC outlet.
AC Outlet
Use the cable ties to bundle the AC adaptor
cable together with the trigger cables.
Other side