Tuning Your Favorite Channels; Tuning To Tile Next Programmed Channel; Tuning To A Specific Channel (Programmed Or Unprogrammed); Switching Between Two Cha*Mels Using Channel Return - Toshiba 32HLV66 Operating Manual

Using the Home feature
When you press B Eon tile remote control, tile TV will be
tuned to the channel or input you set as "Home,"
To set a channel or input as Home:
1 Tune the TV to the channel or input you would like to set
as the Home source.
SS HOME
Press and hold _ on the remote control for 3 seconds.
When HOME is saved, the Channel Browser 'Mbanner will
appear at the bottom of the screen and the HOME icon will
flash green.
To tune to HOME:
SS
HOME
Press the C?D button on the remote to tune to your HOME
channel or input. The Channel Browser rMbanner will display
when HOME is tuned unless all lists have been set to "Off" in
the Channel Browser Setup.
If all lists are set to OFF:
a) you will not be able to set the Home channel/input, if it is not
already set; or
• S SS* HOg,tE
b) if the Home channel/input is aheady ,_et, pre,_smg C?_ on the
remote control will tune to the Home source but will not
display the Channel Browser 'M.
Tuning your favorite channels
To tune to the channels you programmed as Favorite Channels
press FAVA/FAVV or (_)
(ir_ page 21 ).
Tuning to the next programmed channel
To tune to the next programmed channel:
Press _ or _." on the remote control or TV control panel.
Note:Thisfeature will not work unless you program channels
into the TV's channel memory (_, page 19).
Tuning to a specific channel (programmed
or unprogrammed)
Tuning analog channels:
Press the Channel Number buttons (0-9) on the remote
control. For example, to select channel 125, press 1,2, 5.
Tuning digital channels:
Press the Channel Number buttons (0-9) on the remote
control, followed by the dash ((_)) button and then the sub-
channel number. For example, to select digital channel 125-1
press 1,2, 5, -, 1.
Note: If a digital channel is not programmed--either through
the automatic channel scan (_ page 19) or the channel add/
delete function (_ page 19)--you will have to tune the RF
channel using the Channel Number and dash ((_) buttons on
the remote control.
Switching between two channels using
Channel Return
The Channel Return feature allows you to switch between two
channels without entering an actual channel number each time.
1
2
3
Select the first channel you want to view.
Select a second channel using the Channel Number
buttons (and the dash ((_)) button if selecting a digital
channel).
SN CH RTN Pre._'s o on the remote control. The previous channel
ss CHRTN V
"
will display. Each time you press o ,the T will switch
back and forth between the last two channels that were
tuned.
Note: tf you press CH_TN f rom a non-antenna input, the TV
will return to the last-viewed ANT input and channel.
Switching between two channels using
SurfLock
TM
The SurfLock rM feature temporarily "memorizes" one channel
in the CN_TN button, so you can return to that channel quickly
SS" CH RTN
from any other channel by pressing O • To memorize a
channel in the Cn@TN b utton:
1
Tune the TV to the channel you want to program into the
Cn_TN button.
SS CH RTN - Pre.;s and hold O for about _ seconds until the message
"Channel Memorized" appears on screen. The channel
has been programmed into the Cn_TN button.
3
You can then change channels repeatedly, and when you
NN CH RTN
pre.;s © , the memorized channel will be tuned.
The TV will return to the memorized channel one time only.
Once you press Cn_TN and then change channels again, the CH
RTN memory will be cleared and the button will function as
Channel Return, by switching back and forth between the last
two channels that are tuned.
26