Advertisement
Quick Links
MODEL JN1600
Max. cutting capacities
Mild steel
Stainless
1 . 6 m m
1.2"
(1116")
(3164")
INSTRUCTION MANUAL
Min. cutting radius
Continuous
Strokes
Net
Power
,,,Ki t e
length
weight
-
rating
Outside edge
Inside edge
(Input)
1 5 "
7
mm
s o o w
2,200
2 4 5 "
1.5kg
2 m
(5/8")
19/32''
)
(9-5/8") (3.3
Ibs)
(6.6 ft.)
DOUBLE
INSULATION
*
Manufacturer reserves the right t o change specifications o f parts and accessories without notice.
*
Note: Specifications of parts and accessories may vary from country t o country.
Advertisement
Related Manuals for Makita JN1600
Summary of Contents for Makita JN1600
- Page 1 MODEL JN1600 INSTRUCTION MANUAL DOUBLE INSULATION Max. cutting capacities Min. cutting radius Continuous Strokes Power ,,,Ki t e rating length weight Mild steel Stainless Outside edge Inside edge (Input) s o o w 1 . 6 m m 1.2" 2,200 1 5 "...
-
Page 2: Important Safety Instructions
I M PO R TAN T SAFETY I NST R UCT IO NS WARNING: When using electric tools, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and personal injury, including the following: READ ALL INSTRUCTIONS. 1. - Page 3 of moving parts, breakage of parts, mounting, and other conditions that may affect i t s operation. A guard or other part that is damaged should be properly repaired or replaced by an authorized service center unless otherwise indicated elsewhere in this instruction manual.
- Page 4 How t o use Before cutting with the nibbler Coat the cutting line with machine oil when cutting mild steel or stainless; use light oil when cutting aluminum. .Switch operation First, turn the safety lock to the FREE position. Then squeeze the switch lever (paddle switch) to put on the tool;...
- Page 5 Cutting method Smooth cutting achieved holding the tool perpendicular to the material and moving gently in the cutting direc- tion. Apply machine oil to the punch and die about every 10 meters in order to assure clean cutting action. .Cutting corrugated metals cut corrugated sheet metals (with wave-like surfaces), change die orienta- tion and hold the tool so that the cutting...
- Page 6 Blade replacement To replace the blade, use the hex wrench provided to loosen the hold-down screw and remove the die. Then, use the wrench to turn the screw to the left and remove. Next, lift off the punch. Hold-down screw To install the blade, secure the screw and hold-down screw carefully.
-
Page 7: Maintenance
Maintenance Carbon brushes Replace carbon brushes when they wear down to about 3 mm (1/8") or spark- ing will occur. Both brushes should be changed at the same time. To replace the carbon brushes, use minus head screwdriver to remove the brush holder cap. - Page 8 OPTIONAL ACCESSORlES CAUTION: The use of any other accessories not specified in this manual might be hazaroous. Punch Part No. 725005-6 725004-8 Part No.
- Page 9 NIBBLER Model JNI 600...
- Page 10 Punch H. Screw M4x35 (With Warherl Gear Housing [With Plane Bearing 6 & Screw Needle Bearing 8101 F Washer 8 P H Screw M4x30 [With Warherl Switch Cover Needle Bearing 1412 P H Screw M4x18 (With Waherl Crank Shaft Strain Relief Spur Gear 4 4 Brush Holder Cap F.
-
Page 11: Warranty Policy
MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase.