Advertisement
Quick Links
n
D i m e n s i o n s
( L x W x H 1
C a p a c i t i e s
No
load speed
IRPM)
Steel
W o o d
Wood
s c r e w
H i g h
LOW
I
@@
Net
w e i g h t
Equipped with Electric Brake
13 mm (1/2")
MODEL 6300D
13 mm
(1/2")
MODEL 6300DW
With Fast Charger
1 3 "
1112")
INSTRUCTION MANUAL
2 1
mm
5 8 m m x 7 5 m m
2 2 5
mm
x
58 mm
x
2 7 2
mm
2 . 6 k g
113116"l
( 1 5 1 6 4 "
x
2 - 1 5 / 1 6 " )
-
l " oo
~
450
18.718''
x
2 - 5 / 1 6 ' '
x
1 0 - 1 1 / 1 6 " )
( 5 . 7 Ibs)
1 0 . 8
v
1 Hr.
A
C
only
5 0
Hz
~
60
Hr
D . C . 1 0 . 8 V
o u t p u t
Voltage
I
C h a r g i n g t i m e
I
Input
I
Advertisement
Related Manuals for Makita 6300D
Summary of Contents for Makita 6300D
- Page 1 Equipped with Electric Brake 13 mm (1/2") MODEL 6300D 13 mm (1/2") MODEL 6300DW With Fast Charger INSTRUCTION MANUAL IRPM) C a p a c i t i e s load speed D i m e n s i o n s...
-
Page 2: Important Safety Instructions
IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. CONSIDER WORK AREA ENVIRONMENT. - Page 3 REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking t o see that keys and adjusting wrenches are removed from tool before turning AVOID UNINTENTIONAL STARTING. Don't carry plugged-in tool w i t h finger on switch. Be sure switch is when plugging in.
- Page 4 7000. CAUTION - To reduce risk of injury, charge only MAKITA Battery Other types of batteries may burst causing personal injury and damage. 4. Do not expose charger t o rain or snow. Use of an attachment not recommended or sold by the battery charger manufacturer may result a risk of fire, electric shock, or injury t o persons.
-
Page 5: Additional Safety Rules
ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE 1. Do not charge Battery Cartridge when temperature is BELOW 10°C (5OOF) or ABOVE 4OoC (104OF). 2. Do not attempt t o use a step-up transformer, an engine generator or DC power receptacle. - Page 6 Charging Use the Fast Charger DC1000 to charge the Battery Cartridge 1000. To remove the battery cartridge, push up the slide plate and grasp the cartridge care- fully while withdrawing it from the tool. Plug the fast charger into your power source.
- Page 7 Selecting Nominal diameter of wood screw B i t *Phillips bit Use the chart to determine the best size 2.7 (3/32" 1/8") driver bit for the size of screw that you 4.8 (118"- 3/16") wish to use. 5.8 (13164'' 15/64") Slotted bit slotted bit that properly fits the screw slot.
- Page 8 CAUTION Before inserting the battery cartridge into the tool, always check to see that the trigger switch actuates properly and returns to the "OFF" position when released. Reversing switch action This tool has a reversing switch to change the direction of rotation. Slide the revers- ing switch t o the right for clockwise rota- tion or to the left for counterclockwise.
- Page 9 Overload protector The overload protector automatically cuts out to break the circuit and the button pops out, whenever heavy work is pro- longed. When this occurs, release the trigger switch and withdraw the tool from the workpiece. Wait 20 - 30 seconds before pressing the restart button to resume operation.
- Page 10 Drilling operation Drilling in wood When drilling in wood, best results are obtained with wood drills equipped with guide screw. The guide screw makes drilling easier by pulling the bit into the workpiece. Drilling in metal To prevent the bit from slipping when starting hole, make an indentation with center- punch and hammer...
-
Page 11: Maintenance
Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection or maintenance. To maintain product SAFETY and RELlABl LITY, reparis, maintenance or adjustment should be performed by Makita Authorized Factory Service Centers, always using Makita replacement parts. - Page 12 ACC ESSO R I ES CAUTION These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons, The accessories or attachments should be used only in the proper and intended manner,...
- Page 13 M a r . - 1 2 - ' 9 0 13 mm (1/2") CORDLESS DRIVER DRILL Model 63000 Note: The switch and other part configurations may differ from country to country.
- Page 14 -12-'90 630OD MODEL ' L LM $&, DESCRIPTION DESCRIPTION MACHINE MACHINE F l a t Washer 5 Flat Head Screw M6x22 Compresslo" Spring Drill Chuck Thin Washer Spindle Spur Gear Ball Bearing 6000LLB Ring Slop Ring E-9 Pan 3 Compression Spring Shifter Thin Washer Leaf Spring...
- Page 15 YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one-year period, return the COMPLETE tool, freight prepaid, to one of Makita's Factory or Authorized Service Centers.