Xl-hp535e micro component system consisting of xlhp535e
(main unit) and cp-hp535e (speaker system).
xl-hp535h micro component system consisting of xlhp535h
(main unit) and cp-hp535h (speaker system). (88 pages)
It will guide you in operating MICRO COMPONENT SYSTEM your SHARP product. XL-HP600E Micro Component System consisting of XL-HP600E (main unit) and CP-HP600E (speaker system). MODEL XL-HP600E OPERATION MANUAL If you require any advice or assistance regarding your Sharp product, please visit our web-site www.sharp.co.uk/customersupport.
Where plug destroyed immediately and disposed of in a safe manner. this is not possible, please visit our web-site www. sharp.co.uk/ customersupport. Under no circumstances should the cut-off plug be inserted else-...
Page 3
NOTES ! Recording and playback of any material may require consent, which SHARP is unable to give. Please refer particularly to the provisions of the Copyright Act 1956, the Dramatic and Musical Performers Protection Act 1958, the Performers Protection Acts 1963 and 1972 and to any subsequent statutory enactments and orders.
Accessories Contents XL-HP600E Please confirm that the following accessories are included. Page " General Information Precautions ......... . 5 Controls and indicators .
SHARP will not be held responsible for any damage resulting from use of this unit with a voltage other than that ! In case of an electrical storm, unplug the which is specified.
Remote control XL-HP600E ! Battery installation Notes concerning use: " Replace the batteries if the operating distance is reduced or if the Use 2 "AA" size batteries (UM/SUM-3, R6, HP-7 or similar). operation becomes erratic. " Periodically clean the transmitter on the remote control and the Batteries are not included.
System connections XL-HP600E ! Aerial connection FM aerial Supplied FM aerial: AM loop Connect the FM aerial wire to the FM 75 OHMS socket and position aerial the FM aerial wire in the direction where the strongest signal can be received.
XL-HP600E ! Speaker connection Notes: " The unit will start the tape initialisation when plugged in to the AC Connect the black wire to the minus (-) terminal, and the red wire to socket. During this process, initialising sound will be heard and the plus (+) terminal.
Sound control XL-HP600E ! Bass control When the power is first turned on, the unit will enter the extra bass mode which emphasises the bass frequencies, and "X-BASS" will appear. To cancel the extra bass mode, press the X-BASS/DEMO (X-BASS) button.
Setting the clock XL-HP600E Press the TUNING/TIME ( ) button to adjust the hour and then press the MEMORY/SET button. " Press the TUNING/TIME ( ) button once to advance the time by 1 hour. Hold it down to advance continuously.
Listening to a CD (CDs) XL-HP600E This system can also play audio CD-R and CD-RW discs, but can- Press the button to close the disc tray 1. not record. Some audio CD-R and CD-RW discs may not be playable due to the state of disc or the device that was used for recording.
Page 15
XL-HP600E ! To locate the beginning of a track ! To specify a disc to play You can play a disc by specifying the disc number. To move to the beginning of the next track: Press one of the DISC SELECT...
Advanced CD playback XL-HP600E ! Direct search of the track ! Repeat play All tracks on up to 3 discs, all tracks on the chosen disc or a pro- By using the direct search buttons, the desired tracks on the current grammed sequence can be continuously repeated.
XL-HP600E ! Programmed play To clear the programmed selections: Press the CLEAR button on the remote con- You can choose up to 32 selections for playback in the order you trol whilst the "MEMORY" indicator is flashing. like. Each time the button is pressed, one track will be cleared, beginning with the last track programmed.
Listening to the radio XL-HP600E ! Tuning Press the ON/STAND-BY button to turn the power on. Press the TUNER (BAND) button repeatedly to select the desired frequency band (FM or AM). Press the TUNING/TIME ( ) button to tune in to the de- sired station.
XL-HP600E ! Memorising a station ! To recall a memorised station You can store 40 AM and FM stations in memory and recall them at Press the PRESET ( ) button for less than 0.5 seconds to se- the push of a button. (Preset tuning) lect the desired station.
Listening to a cassette tape XL-HP600E Before playback: Press the ON/STAND-BY button to turn the power on. " For playback, use normal or low-noise tapes for the best sound. (Metal or CrO tapes are not recom- Press the TAPE button.
Press the (TAPE ) button. ensure that the desired material is properly recorded. ! SHARP is not liable for damage or loss of your recording arising Fast forward/rewind on side A: from malfunction of this unit. To advance the tape, press the button.
Page 22
Recording to a cassette tape (continued) XL-HP600E " Recording from a CD (CDs) You can record the desired CD using the DISC SELECT 3) buttons. Press the ON/STAND-BY button to turn the power on. Press the CD button and load the desired disc.
XL-HP600E " Recording from the radio Recording from several CDs continuously: 1 Perform steps 1 - 5 in "Recording from a CD (CDs)" on page 22. Tune in to the desired station. (See page 18.) 2 Press the ( ) button to record on side A, or the button for side B.
Timer and sleep operation XL-HP600E " Timer playback or timer recording Timer playback: The unit turns on and plays the desired source (CD, tuner, tape) at Before setting timer: the preset time. 1 Press the CLOCK button to check that the clock is set to the cor- rect time.
Page 25
XL-HP600E To reset or change the timer setting: Press the TUNING/TIME ( ) button to specify the hour Perform "Timer playback or timer recording" from the beginning. to start, then press the MEMORY/SET button. Note: When performing timer playback or recording using another unit con- nected to the VIDEO/AUX sockets, select "VIDEO/AUX"...
Enhancing your system Timer and sleep operation (continued) XL-HP600E ! Sleep operation The connection lead is not included. Purchase a commercially avail- able lead as shown below. Play back the desired sound source. VCR, DVD, etc. Press the TIMER/SLEEP button repeatedly until "SLEEP" is displayed.
XL-HP600E ! To record on a tape ! Subwoofer connection When a commercially available speaker with a built-in amplifier is Insert a cassette in the cassette compartment. connected to this unit, you can enjoy sound with emphasised bass. Connect an RCA lead from a commercially available speaker with a Press the VIDEO/AUX button.
Possible cause If something is wrong with this product, check the following before " Radio makes unusual " Is the unit placed near the TV or calling your authorised SHARP dealer or service centre. noise consecutively. computer? ! General " Is the FM aerial or AM loop aerial...
Page 29
XL-HP600E ! Remote control ! Clearing all the memory (reset) 1 Press the ON/STAND-BY button to enter the power stand-by Symptom Possible cause mode. " The remote control does " Is the AC power lead of the unit 2 Whilst pressing down the button and the X-BASS/DEMO not operate.
Specifications XL-HP600E ! Cleaning the tape-handling parts As part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for product " Dirty heads, capstans or pinch rollers can cause poor sound and improvement without prior notice. The performance specification fig- tape jams.
Page 31
XL-HP600E ! CD player ! Speaker Type 3-disc multi-play compact disc changer Type 2-way type speaker system player 5 cm (2") tweeter Signal readout Non-contact, 3-beam semiconductor laser 13 cm (5-1/8") woofer pickup Maximum input 150 W D/A converter 1-bit D/A converter...
3. To benefit from this guarantee, any fault which occurs must be notified to Sharp, or its appointed Service Facility within one year from the date this product was purchased. Proof of purchase must be provided.