Scag Power Equipment SWZ Operator's Manual page 18

Ref. Part
No. No. Description
1 46850 Cutter Deck (Includes decals)
2 46631 Cutter Spindle Assembly
3 43312 Spacer, Outside
4 48307-08 Tapered Nut, 5/16-24
5 481022 Tapered Bearing (two)
6 43294 Spindle Housing, Tapered Bearing
7 04001-108 Bolt,5/16-18 x 4-1/14" Hex Head
8 43298 Spindle Shaft
9 04001-77 Hex Head Bolt, 3/8-16 x 3-1/2"
10 04063-08 Key, 1/4 x 2"
11 43278 Spacer, Cutter Blade
12 04001-10 Hex Head Bolt, 5/16-18 x 1-1/4"
13 481050 Spring, Chute Return
14 04019-03 Nut, 5/16-18 Serrated Flange
15 48108 Cutter Blade, 18"
15A 48185 Cutter Blade, 18" High Lift
16 04040-10 Flat Washer, 5/8" W
17 04001-41 Hex Hd. Bolt, 5/8-11 x 9-1/2"
18 46079 Caster Assembly (includes 19-28)
19 04066-01 Quick Pin
20 43037-01 Spacer, Caster Yoke, 1/2" thick
21 48100-01 Bronze Bearing
22 48114-04 Grease Fitting
23 46082 Support Assy. (incl. 21-23)
24 45006 Caster Yoke
25 43022 Sleeve, Caster Wheel Bearing
26 04001-37 Hex Hd. Bolt, 1/2-13 x 5-1/2"
27 04021-07 Hex Locknut, 1/2-13
28 48307 Wheel Assy. (incl. 4,29-34)
29 48307-02 Tire only, Caster Wheel
NS 48006-03 Inner Tube Only (not shown)
30 48307-04 Rim Pair, Caster Wheel
31 48006-07 Retainer, Bearing, Caster Wheel
32 48006-06 Roller Bearing, Caster Wheel
33 48114-03 Grease Fitting 45 deg., 1/4-28
34 48006-05 Hub Assy. (incl. bolts)
35 04017-16 Capscrew, 5/16-18 x 3/4" Serr. Flange Hex Head
36 461054 Discharge Chute
37 04021-10 Hex Nut, 5/16-18 Elastic Stop
38 04001-09 Hex Head Bolt, 5/16-18 x 1"
39 46797 Belt Cover Assembly
* Common hardware which should be purchased locally. All bolts Grade 5 plated, all other fasteners zinc plated.
36" CUTTER DECK
Ref. Part
No. No.
40 04041-07
41 04029-03
42 48924
43 48926
44 04001-01
45 04020-09
46 48204
47 43077
48 04021-05
49 04019-04
50 04004-02
51 04017-42
52 04019-05
53 43277
54 04041-07
55 04021-09
56 45423
57 46748
58 48100-02
59 04050-05
60 44078
61 48269
62 481024
63 43297
64 43296
65 481035
66 48677
67 481025
68 48098
69 04029-04
3
Description
Flat Washer, 3/8" (.391 x .938 x .105)
Wing Nut, 3/8-16
Pulley
Tapered Hub, 1.125 Bore
Hex Head Bolt, 1/4-20 x 3/4"
Hex Nut, 5/8-11
Belt, Blade Drive
Spacer
Nut, Center Locknut - 3/8-16
Nut, 3/8-16 Serrated Flange
Support, Belt Cover
Capscrew, 7/16-14 x 1" Serr. Flange
Hex Nut, 7/16-14 Serrated Flange
Spacer, J-Hook
Flat Washer
Nut, 3/8-16 Elastic Stop
Idler Pivot
Idler Arm Assy. (incl. 22 & 58)
Bushing, 1-1/8 x 1.0 Flanged
Retaining Ring, 1-1/8" Ext. "E"
J-Hook
Idler Pulley, Belt Clutch
Seal, Cutter Spindle
Spindle Bushing
Spacer, Inside
Nut
Relief Fitting, Cutter Spindle
Seal, Cutter Spindle
Shield, Spindle
Wing Nut 3/8-16 (SM)