Inventory - Grizzly G0555X EXTREME SERIES Owner's Manual
14" extreme series bandsaw
Hide thumbs
Also See for G0555X EXTREME SERIES:
- Owner's manual (60 pages) ,
- Parts breakdown (7 pages) ,
- Owner's manual (59 pages)
Table of Contents
Advertisement
Inventory
The following is a description of the main compo-
nents shipped with your machine. Lay the compo-
nents out to inventory them.
If any non-proprietary parts are missing (e.g. a
nut or a washer), we will gladly replace them; or
for the sake of expediency, replacements can be
obtained at your local hardware store.
Main components: (figure 3)
A. stand .......................................................... 1
B. bandsaw unit ............................................. 1
c. trunnion base ............................................ 1
D. lever board ................................................ 1
E. Miter gauge ................................................ 1
f.
extension table .......................................... 1
G. Main table .................................................. 1
h. Fence assembly ......................................... 1
I.
resaw Fence ............................................. 1
J.
Front Fence rail ......................................... 1
K. rear Fence rail ......................................... 1
fasteners and Tools: (not shown)
•
rubber Feet (stand) .................................. 4
•
hex nuts
⁄
-16 (Feet/stand) ...................... 8
3
8
•
Flat Washers 10mm (Feet/stand) .............. 8
•
hex bolts M8-1.25 x 35 (bandsaw/stand) . 4
•
Flat Washers 8mm (bandsaw/stand) ........ 8
•
lock Washers 8mm (bandsaw/stand) ....... 4
•
hex nuts M8-1.25 (bandsaw/stand) .......... 4
•
hex bolts M8-1.25 x 30 (trunnion base) ... 2
•
lock Washers 8mm (trunnion base)......... 2
•
hex bolt M8-1.25 x 80 (positive stop) ....... 1
•
hex nut M8-1.25 (positive stop) ............... 1
•
spacers (lever board) ............................... 4
•
Cap screws M8-1.25 x 60 (lever board) .. 4
•
hex nuts M8-1.25 (lever board) ............... 4
•
set screws M8-1.25 x 20 (lever board) .... 4
•
Cap screws M6-1 x 25 (lever board) ....... 4
•
lock Washers 6mm (lever board) ............ 4
•
Flat Washers 6mm (lever board) .............. 4
•
Knobs M10-1.5 (table) .............................. 2
•
hex bolts M6-1 x 20 (Front rail) ............... 2
•
Flat Washers 6mm (Front rail) .................. 2
•
lock Washers 6mm (Front rail) ................ 2
•
Cap screws M6-1 x 16 (rear rails) .......... 2
•
lock handle M8-1.25 x 20 (Fence) ............ 1
•
hex nut M8-1.25 (Fence) ........................... 1
g0555X (Mfg. since 1/12)
•
Moving plate (resaw) ................................ 1
•
lock handle M8-1.25 x 44 (resaw) ........... 1
•
Flat Washer 8mm (resaw) ........................ 1
•
hex Wrenches 3, 4, 5mm ................. 1 each
Qty
C
e
Qty
F
figure 3. Main components inventory.
If you cannot find an item on this list, care-
fully check the machine and the packaging
materials. Some of these items may be pre-
installed for shipping or become misplaced
during unpacking.
b
a
d
g
h
i
NOTICE
J
K
-13-
Advertisement
Table of Contents
