Rear Panel Function; Specifications - Fender 1000 Roc-Pro Instruction Manual

2 3
1
1. LINE CORD - Connect the power line cord to a
grounded AC receptacle in accordance with the volt-
age and frequency ratings as listed on the rear panel of
the amplifier.
2. 8 OHM SPEAKER JACK (Combo & Head models) -
Plug-in connection for external 8 ohm speakers only.
3. 4-OHM ADDITIONAL SPEAKER JACK (Head model
only) - Plug-in connection for a external 4 ohm speaker
or a second 8 Ohm speaker enclosure. The combined
minimum impedance for all speaker enclosures should
be 4 ohms (i.e. two 8 ohm enclosures in parallel).
TUBE REPLACEMENT: Roc Pro amplifiers utilize one Fender Special Design 12AX7A vacuum tube. It's a good idea to keep a spare
tube with the amplifier in case the tube in the Roc Pro should fail and as a test for tube wear. Loss of sound quality due to the tube
reaching the end of its life is very gradual and may not be noticed. Replacing the old tube with your spare and listening for improvement
will tell if the old tube is worn and whether you should replace it and buy a new spare! Replace only with the identical tube type.
TYPE:
PART NUMBERS: (Combo)
22-6808-000 (120V, 60 Hz)USA; 22-6868-000 (230V, 50 Hz)Euro;
22-6838-000 (240V, 50 Hz)Aust; 22-6878-000 (100V, 50/60 Hz)Jpn
POWER REQUIREMENTS:
INPUT IMPEDANCE:
NOMINAL LEVEL:
POWER OUTPUT:
EFFECTS LOOP: NOMINAL LEVEL:
OUTPUT IMPEDANCE:
INPUT IMPEDANCE:
TUBE COMPLEMENT:
SPEAKER (Combo only):
EXTERNAL SPEAKER:
FOOTSWITCH (Included):
DIMENSIONS:
R e a r P a n e
R e a r P a n e
4 5 6
7
S p e c i f
S p e c i f
PR 209
300W
> 1 M
100mV
69W into 8 at 5% THD
Selectable +4, -7, -16 dBv
1.2 k max.
100k
One 12AX7A (ECC83) (P/N 013341)
8 , 12" Fender Special Design (P/N 040598)
(Combo) Fender recommends Guitar enclosure GE-112 Mk II (P/N 21-1660-010) @ 8
(Head) Fender recommends Guitar enclosure GE-412 Mk II (P/N 21-1662-010) @ 4
3 button: Gain, Gain Select and Reverb
(Combo)
HEIGHT: 17.5 in. (44.5 cm)
WIDTH: 22.5 in. (56.8 cm)
DEPTH: 10.25 in. (25.9 cm)
WEIGHT: 41 lbs. (18.6 kg)
Product specifications are subject to change without notice.
l F u n c t i o n s
l F u n c t i o n s
4. LINE OUT - This jack provides a signal output suitable
for connection to recording and sound reinforcement
equipment. Using a 3-conductor stereo cord will pro-
vide a quasi-balanced signal and a 2-conductor mono
cord will provide an unbalanced signal.
5. SEND - Connect cord to external equipment at this
output jack. This unbalanced jack provides a pre-
reverb signal output from the preamp and may be used
to drive effects units in an effects loop, to drive addi-
tional amplifiers in a multi-amp set up or as a preamp
send to a mixing console.
6. LEVEL SWITCH - This switch directly effects the SEND
jack (item 5) by boosting or attenuating the signal sent
to the effects. External rack effects usually require
–7dB or +4dB settings. Effects pedals usually require
a –16dB setting.
7. RETURN - Connect cord from external effects devices
at this input jack. Inserting a plug at this jack auto-
matically disconnects the unit's internal connection
from the pre-amp to the power amp. This jack is pre-
reverb and can also be used as a power amp input.
Plugging into this jack activates the EFFECTS MIX
control on the front panel.
i c a t i o n s
i c a t i o n s
22-6807-000 (120V, 60 Hz)USA; 22-6867-000 (230V, 50 Hz)Euro;
22-6837-000 (240V, 50 Hz)Aust; 22-6877-000 (100V, 50/60 Hz)Jpn
94W into 4 at 5% THD
(Head)
8.5 in. (21.6 cm)
22.5 in. (56.8 cm)
9.5 in. (24.1 cm)
25 lbs. (11.4 kg)
5
(Head)