Table of Contents
Advertisement
UNIVERSAL
REMOTE
CONTROL
PROGRAMMING
YOUR
REMOTE
If you are using Inteq products,
the remote is programmed
for
the most commonly
used codes. For other brands -- or if your
remote fails to control your Inteq products
-- you will have to
pro_am
the remote.
Follow these steps for each product
you are using:
1.
Look
up the three-digit
code
for your brand
(such
as
Zenith)
amt type of equipment
(such
as VCR)
in the
code
table
oil the following
page.
2.
Press
and hold PRG
with
a small
blunt
object
until
the indicator
lights
(about
three
seconds).
3.
Press
TV, VCR,
CABLE,
or AUX to select
the
product
you want
your remote
to control.
(Use
('.ABLE
or AUX,
to program
your remote
for a
second
TV or VCR
or to program
your remote
for a
video
disc player
or audio
equipment.)
4.
Key in the three-digit
code
fc,r your equipment,
then
pres_,; ENTER/TUNE.
The indicator
light should
flash,
then turn off to indicate
that the code was
accepted.
If the indicator
stays on, repeat
steps 2, and 4
or try using
a different
code
5.
Write
the codes
that operate
your equipment
on the
label
inside
the battery
compartment
for fu_ture
reference.
To erase al! code programming
and return to the factory preset
codes, key in code 9-1-1
when programming
the remote.
NOTES:
O The remote cannot be programmed while in the StarSight
mode: Choose TV, VCR, CABI,E or AUX mode before
pressing PRG.
rq If no key on your remote is pressed within 60 seconds, the
programming process will stop, and you will have to start
again.
O You may cancel programming at any time by pressing PRG.
SPF.CIAL
FEATURES
AUX+I, AUX+2, AUX+3 Capability
Your remote can control up to seven electronic components. If
you have programmed the remote for four components using
the TV, VCR, CABLE and AUX keys, you may also program it
for up to three additional components (AUX+I, AUX+2,
AUX+3) by holding the AUX key and pressing the 1, 2 or 3 key
during programming. Once programmed, hold down the AUX
key and press 1, 2 or 3, to access the additional AUX +1, 2 or 3
mode.
Cable Box Volume
You ]nay use your remote to control cable box volume and mut-
ing if available on your equipment.
First program your remote
with ,:he brand ccde for your cable device using the CABLE
or
AUX key. Then repeat the programming
steps, again using the
CABLE
or AUX key, but key in code 3-9-9
instead of a brand
code.
To restore TV volume/mute
control to the CABLE
or AUX
mode, reprogram
your cable code into that mode.
Amplifier
Volume
Override
You may use your remote to override
your TV, VCR or video
disk player's volume functions with your _unplifier's volurne and
muting.
1.
Program
your amplifier
code into
the CABLE
mode
or one of the AUX
modes.
2.
Selezt
the mode
on your remote
(TV, VCR,
etc.)
where
you want
the amplifier
volume
control
function
to appear.
In other
words,
if you want
to
operate
the volume
and mute of your amplifier
while
the remote
is in TV mode,
press
TV for this
step.
3.
Begin
the programming
steps
as described
in
"Programming
Your Remol:e"
and enter
code
4.-9-9,
followed
by ENTER.
The amplifier
volume
and mute features
are nov/
avaiiable
in the current
mode.
To restore normal volume
and muting control to your TV,
VCR, cable or laser disc player, reprogram
the remote for these
units into each mode (TV, VCR, etc.) to be restored.
NOTE:
O CD and tape devices will automatically
select amplifier
vol-
ume and mute.
2949-01-A
4--4
Advertisement
Table of Contents
