Genie Z-34 Bi-Energy Operator's Manual
  1. Manuals
  2. Brands
  3. Genie Manuals
  4. Boom Lifts
  5. Z-34 Bi-Energy
  6. Operator's manual
Genie Z-34 Bi-Energy Operator's Manual

Genie Z-34 Bi-Energy Operator's Manual

Hide thumbs Also See for Z-34 Bi-Energy:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Service & Repair Manual
Operator's Manual
with Maintenance Information
First Edition
Fifth Printing
Part No. 56011

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Z-34 Bi-Energy and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Genie Z-34 Bi-Energy

Summary of Contents for Genie Z-34 Bi-Energy

  • Page 1 Operator’s Manual First Edition Fifth Printing with Maintenance Information Part No. 56011...

  • Page 2: Table Of Contents

    Contact us: First Edition: Fifth Printing, September 2002 Internet: http://www.genielift.com "Genie" and "Z" are registered trademarks of e-mail: techpub@genieind.com Genie Industries in the U.S.A. and many other countries. These machines comply with ANSI/SIA 92.5-1992. Printed on recycled paper Printed in U.S.A.

  • Page 3: Safety

    You read, understand and obey: Manufacturer's instructions and safety rules—safety and operator's manuals and machine decals Employer's safety rules and worksite regulations Applicable governmental regulations You are properly trained to safely operate the machine. Part No. 56011 Genie Z-34/22 Bi-Energy...
  • Page 4 Do not operate the machine during lightning or storms. Do not use the machine as a ground for welding. Genie Z-34/22 Bi-Energy Part No. 56011...
  • Page 5 Do not drive the machine on or near uneven terrain, unstable surfaces or other hazardous conditions with the boom raised or extended. Do not place ladders or scaffolds in the platform or against any part of this machine. Part No. 56011 Genie Z-34/22 Bi-Energy...
  • Page 6 Keep the platform floor clear of debris. Do not operate the machine in hazardous Lower the platform entry mid-rail or close the entry locations or locations where potentially flammable gate before operating. or explosive gases or particles may be present. Genie Z-34/22 Bi-Energy Part No. 56011...
  • Page 7 It is recommended that operators wear an approved hard hat when operating the machine. Be sure all maintenance has been performed as specified in this manual and the Genie Z-34/22 Observe and use color-coded direction arrows on Bi-Energy Service Manual.
  • Page 8 Component Damage Hazards Decal Legend Do not use any battery or charger greater than Genie product decals use symbols, color coding 12V to jump-start the engine. and signal words to identify the following: Do not use the machine as a ground for welding.

  • Page 9: Controls

    · Turtle: low idle 7 Red Emergency Stop button · Rabbit: high idle and 19 Turntable rotate switch 8 Not used quickest battery charging 20 Platform rotate switch 9 Battery charge indicator 13 Engine start switch (option) Part No. 56011 Genie Z-34/22 Bi-Energy...
  • Page 10 Auxiliary power switch · rabbit: high idle and quickest battery Not used charging Travel alarm Remote brake release Key switch for platform/off/ground selection Jib boom up/down switch Red Emergency Stop button Secondary boom up/down switch Genie Z-34/22 Bi-Energy Part No. 56011...

  • Page 11: Pre-Operation Inspection

    Scheduled maintenance inspections shall be performed by qualified service technicians, according to the manufacturer's specifications and the requirements listed in the responsibilities manual. Part No. 56011 Genie Z-34/22 Bi-Energy...
  • Page 12 Fuel and hydraulic tanks o Drive and turntable motors and torque hubs o Boom wear pads o Tires and wheels o Engine and related components o Limit switches, alarms and horn o Nuts, bolts and other fasteners Genie Z-34/22 Bi-Energy Part No. 56011...

  • Page 13: Maintenance

    Indicates that tools will be required to perform this procedure. Indicates that new parts will be required to perform this procedure. Part No. 56011 Genie Z-34/22 Bi-Energy...
  • Page 14 1 Check the fluid level in the coolant recovery tank. Add fluid as needed. Result: The fluid level should be at the mark. FULL Genie Z-34/22 Bi-Energy Part No. 56011...
  • Page 15 1 Check each tire with an air pressure gauge and add air as needed. Tire specifications Industrial tire 9-14.5 LT 100 psi (6.89 bar) Rough terrain tire 10-16.5 NHS 45 psi (3.1 bar) Part No. 56011 Genie Z-34/22 Bi-Energy...

  • Page 16: Function Tests

    After repairs are completed, the operator must perform a pre-operation inspection and function tests again before putting the machine into service. Genie Z-34/22 Bi-Energy Part No. 56011...
  • Page 17 Drive and steer functions are not affected by the boom function speed controller. Machines equipped with Platform Level Control Disable Function: The platform level toggle switch will not operate when the primary boom is raised past the drive speed limit switch. Part No. 56011 Genie Z-34/22 Bi-Energy...
  • Page 18 Note: The brakes must be able to hold the machine on any slope it is able to climb. Genie Z-34/22 Bi-Energy Part No. 56011...
  • Page 19 Use the color-coded Blue direction arrows on the platform controls and the drive chassis to identify the direction of travel. Yellow Part No. 56011 Genie Z-34/22 Bi-Energy...

  • Page 20: Workplace Inspection

    It is the operator's responsibility to read and remember the workplace hazards, then watch for and avoid them while moving, setting up and operating the machine. Genie Z-34/22 Bi-Energy Part No. 56011...

  • Page 21: Operating Instructions

    That means every new operator should perform a pre-operation inspection, function tests, and a workplace inspection before using the machine. Part No. 56011 Genie Z-34/22 Bi-Energy...
  • Page 22 Machines equipped with Platform Level Control Disable Function: The platform level toggle switch will not operate when the primary boom is raised past the drive speed limit switch. Genie Z-34/22 Bi-Energy Part No. 56011...
  • Page 23 3 Press down the foot switch when operating the discharged. auxiliary controls from the platform. 4 Simultaneously hold the auxiliary power switch on and activate the desired function. The drive function will not operate with auxiliary power. Part No. 56011 Genie Z-34/22 Bi-Energy...
  • Page 24 Be sure the engine is not running. Use the AC battery charger included with the machine for overnight charging. The charger shuts off automatically. Periodically, use the AC battery charger to fully charge the batteries. Genie Z-34/22 Bi-Energy Part No. 56011...

  • Page 25: Transport & Lifting Instructions

    Be over the torque hub disconnect caps (see sure to unlock the turntable for operation. below). Towing a Genie Z-34/22 Bi-Energy machine is not recommended. If the machine must be towed, do not exceed 2 mph / 3.2 km/h. Disengage...
  • Page 26 Use the tie points on the drive chassis for anchoring down to the transport surface. Use chains or straps of ample load capacity. Use a minimum of 4 chains. Adjust the rigging to prevent damage to the chains. Genie Z-34/22 Bi-Energy Part No. 56011...
  • Page 27 Be sure the crane capacity, loading surfaces machine and to keep the machine level. and straps or lines are sufficient to withstand the machine weight. See serial plate. X Axis 35.9 in 91.3 cm Y Axis 33.3 in 84.7 cm Part No. 56011 Genie Z-34/22 Bi-Energy...

  • Page 28: Decals

    Label - Controller Status Indicator Light 31785 Notice - Battery Charger Instructions 52968 Cosmetic - Genie Boom 31788 Danger - Battery/Charger Safety 62924 Cosmetic - Genie Z-34/22 Bi-Energy 32700 Danger - Safety Rules 62930 Cosmetic - Genie Z-34/22 33952 Danger - Tilt-Alarm 72092...
  • Page 29 First Edition • Fifth Printing Operator's Manual DECALS Ground Controls Side Platform Drive Chassis - Top Engine Side Shading indicates decal is hidden from view, i.e. under covers Part No. 56011 Genie Z-34/22 Bi-Energy...

  • Page 30: Specifications

    10-16.5NHS Airborne noise emissions 80 dB Maximum sound level at normal operating workstations (A-weighted) Continuous improvement of our products is a Genie Weight See Serial Plate policy. Product specifications are subject to change (Machine weights vary with option configurations) without notice or obligation.
  • Page 31 The exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Genie North America Phone Toll Free Genie Holland Genie Australia Pty Ltd. Phone + Phone + Fax + Fax + Genie China Genie Scandinavia...

This manual is also suitable for:

Z-22 bi-energy

Table of Contents