Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Troy-Bilt Manuals
  4. Snow Blower
  5. Storm Tracker 31AH7T74063
  6. Operator's manual

Troy-Bilt 31AH7T74063 Storm Tracker Operator's Manual

Hide thumbs Also See for 31AH7T74063 Storm Tracker:

Advertisement

Quick Links

Download this manual
OTRO_ BILT'__
OPERATOR'S
MANUAL
SNOW
THROWER
MODEL
31AH7T74063
Storm Tracker
IMPORTANT:
READ SAFETY
RULES AND INSTRUCTIONS
CAREFULLY
WARNING:
This unit is equipped with an internal combustion engine and should not be used on or near any unimproved
forest-covered,
brush-covered
or grass-covered
land unless the engine's exhaust system is equipped with a spark attester
meeting applicable local or state
laws (if any). If a spark arrester is used, it should be maintained in effective working order by the operator. In the State of California the above
is required by law (Section 4442 of the California Public Resources Code). Other states may have similar laws. Federal laws apply on federal
lands. A spark attester for the muffler is available through your nearest engine authorized service dealer or contact the service department,
P.O. Box 361131 Cleveland, Ohio 44136-0019.
TROY-BILT
LLC, P.O. BOX 361131 CLEVELAND,
OHIO 44136-0019
FORM NO. 769-00395
PRINTED IN U.S.A.
(9/02)

Advertisement

loading

Related Manuals for Troy-Bilt 31AH7T74063 Storm Tracker

Summary of Contents for Troy-Bilt 31AH7T74063 Storm Tracker

  • Page 1 (Section 4442 of the California Public Resources Code). Other states may have similar laws. Federal laws apply on federal lands. A spark attester for the muffler is available through your nearest engine authorized service dealer or contact the service department, P.O. Box 361131 Cleveland, Ohio 44136-0019. TROY-BILT LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019 FORM NO.

  • Page 2: Table Of Contents

    TABLEOFCONTENTS Content Page Important Safe Operation Practices ..............Assembling Your Snow Thrower ................ Know Your Snow Thrower ................. Operating Your Snow Thrower ................Making Adjustments ..................Maintaining Your Snow Thrower ................ Service ....................... Troubleshooting ....................Parts List ......................FINDINGMODEL NUMBER This Operator's Manual is an important part of your new snow thrower.

  • Page 3: Important Safe Operation Practices

    SECTION 1: IMPORTANT SAFEOPERATION P RACTICES This symbol points out important safety instructions, which if not followed, could endanger the personal safety and/or property of yourself and others. Read and follow all instructions in this manual before attempting to operate this machine. Failure to comply with these instructions may result in personal injury.
  • Page 4 5. Never runanengine i ndoors orinapoorly v entilated ofyour n earest servicing dealer. area. E ngine e xhaust contains carbon m onoxide, an odorless and deadly g as. MAINTENANCE A NDSTORAGE 6. Donot o perate m achine while under theinfluence of alcohol ordrugs.

  • Page 5: Assembling Your Snow Thrower

    SECTION 2: ASSEMBLING YOUR SNOW THROWER NOTE: References to right or left side of the snow • Raise the upper handle assembly until it locks over thrower are determined from behind the unit in the the lower handle. • Look at the lower rear of snow thrower frame to be operating position.

  • Page 6: Know Your Snow Thrower

    SECTION 3: KNOW YOUR SNOW THROWER Shift Lever q Traction Control / Auger Control Lock Chute Tilt jTool Heated Switch Headlight_ Clean-out Discharge_ _Track Steering Control Chute F_ ' Electric __/Starter LNp_-L-_ Button Prime_ Switch Choke_ Chute Directional _< Control Safety _ Ignition Key J/i/j_...
  • Page 7 HeatedHandles Switch Headlight This switch is located on the right side of the snow The headlight is on whenever the engine is running. thrower dash panel. To activate the heated handles, TrackLockLever toggle the switch to the right to generate heat within the handle grips.
  • Page 8 ToStartEngine • Push primer button two or three times. If engine is warm, push primer button once only. • Attach spark plug wire to spark plug. Make certain NOTE: Always cover vent hole in primer button when the metal loop on end of the spark plug wire (inside pushing.

  • Page 9: Operating Your Snow Thrower

    ChuteClean-Out T ool ToEngage Augers • To engage the augers and start throwing snow, The chute clean-out tool is conveniently fastened to the squeeze the auger control grip against the left rear of the auger housing with a mounting clip. Should handle.
  • Page 10 Operating Tips • Discharge the snow downwind whenever possible. • Slightly overlap each previous path. • Set the skid shoes 1/4" below the shave plate for NOTE: Allow the engine to warm up for a few minutes. normal usage. The skid shoes may be adjusted The engine will not develop full power until it reaches upward (to lower the shave plate) for hard-packed operating temperature.
  • Page 11 If adjustment is necessary: • Reconnect the upper shift rod to the lower shift rod by reinserting the hairpin clip removed earlier and • Loosen the jam nut on the traction drive cable. sliding the shift rod connector back down into place. Adjust the cable as necessary.
  • Page 12 SECTION 6: MAINTAINING YOUR SNOW THROWER WARNING: Before lubricating, repairing, is free of grease in order to relieve pressure. or inspecting, disengage all clutch levers AugerShaft and stop engine. Wait until all moving At least once a season, remove the shear bolts on the parts have come to a complete...
  • Page 13 Augers Drain the gasoline from the snow thrower, or place • a piece of plastic film under the gas cap. • The augers are secured to the spiral shaft with two • Tip the snow thrower up and forward so that it rests shear bolts and hex lock nuts.
  • Page 14 • Drain the gasoline from the snow thrower. • Tip the snow thrower up and forward, so that it rests on the housing. Refer to Figure 9. Support • Remove six self-tapping screws from the frame Bracket cover underneath the snow thrower. Frame •...
  • Page 15 NOTE: Fuel stabilizer is an acceptable alternative Shift Rod minimizing the formation of fuel gum deposits during Assembly storage. Do not drain carburetor if using fuel stabilizer. Spacer • Wipe equipment with an oiled rag to prevent rust. • Remove spark plug and pour one ounce of engine oil through spark plug hole into cylinder.

  • Page 16: Making Adjustments

    SECTION 8: TROUBLESHOOTING Problem Cause Remedy Engine fails to start Fuel tank empty, or stale fuel. Fill tank with clean, fresh gasoline. Fuel becomes stale after thirty days. Clean the fuel line. Blocked fuel line. Choke not in the ON position Move switch to the ON position Faulty spark plug.
  • Page 17 Model31AH7T74063 Ref. Part No. Part Description 618-0123 RH Housing 618-0124 LH Housing 710-0642 Self Tapping Screw, 1/4-20 x .75 711-0910A Spiral Axle 28" 714-0161 Hi-Pro Key, 3/16 x 5/8 715-0143 Spring Spiral Pin, .25 x 1.25 717-0528 Worm Gear, 204ooth Worm Shaft 717-0526 Thrust Collar...
  • Page 18 Model31AH7T74063 "15...
  • Page 19 Model31AH7T74063 Ref. Ref. Part No. Part No. Part Description Part Description Control Cable 684-0008A 746-0901 Shift Arm Assembly 710-0458 741-0475 Carriage Bolt 5/16-18 x 1.75" Plastic Bushing 710-0449 736-0159 5/16 Washer Carriage Bolt 5/16-18 x 2.25" Cable Bracket 710-0788 TT Screw 1/4-20 x 1" 784-5594 710-0837 C-Sunk Screw #10-16x 0.625"...
  • Page 20 Model31AH7T74063 °26 \\_\\\\33...
  • Page 21 Model31AH7T74063 Ref. Ref. Part No. Part No. Part Description Part Description 712-3010 Hex Nut 5/16-18 712-0116 Lock Jam Nut 3/8-24 756-0178 Flat Idler 784-5582A Shave Plate 710-0451 784-5632B Carriage Bolt 5/16-18 x 1.00 Auger Idler Arm 710-0459A 684-0065 Hex Cap Screw 3/8-24 x 1.50 Impeller Assembly 738-0281 Shoulder Screw...
  • Page 22 Model31AH7T74063 11 10 21 16 22 \ 24 /...
  • Page 23 Models 31AH7T74063 Ref. Part No. Part Description Hex Washer Screw 1/4-20 x .625 710-1652 731-1324 Belt Cover 732-0710 Extension Spring 710-0627 Hex Screw 5/16-24 x .75 710-3005 Hex Cap Screw 3/8-16 x 1.25 05896A Drive Clutch Idler Bracket 748-0234 Shoulder Spacer 756-0987 Pulley Half 754-0346...
  • Page 24 Models 31AH7T74063 2£ 19 26...
  • Page 25 Model31AH7T74063 Ref. Ref. Part No. Part No. Part Description Part Description Frame Cover 736-0270 Bell Washer .265 ID x .75 OD 784-5648 710-1652 736-0176 Flat Washer 1/4 ID x .93 OD Tap Screw 1/4-20 x .625 741-1111 748-0190 Spacer .508 ID x .75 OD Hex Flange Bearing 732-0264 710-0643...
  • Page 26 Models 31AH7T74063...
  • Page 27 Models 31AH7T74063 Ref. Part No. Part Description Part No. Part Description 720-0223 Grip 618-0169A Track/Steering Shaft Assy 710-0604A Tap Screw, 5/16-18 x .625 683-0024 Track Hub Assy Chain 784-5642 Track Lockout Plate 713-0437 710-0157 741-0339 Hex Cap Screw, 5/16-24 x .75 Flange Bearing 736-0242 Bell Washer, .34 ID x .872 OD...
  • Page 28 MANUFACTURER'S LIMITED WARRANTY FOR: O TRO_ B_ILT_ The limited warranty set fodh below is given by Troy-Bilt LLC Troy-Bilt LLC does not extend any warranty for products sold or exported outside of the United States, with respect to new merchandise purchased and used in the United States, its possessions and territories.