Important Precautions; Assembly - LIFESTYLER CARDIO FIT PLUS User Manual

2.
IMPORTANT PRECAUTIONS
WARNING: To reduce the risk of
serious injury, read the following
important precautions before using
the SEARS*' LIFESTYLER CARDIO
FIT PLUS.
1. Use the CARDIO FIT PLUS only
on a level surface.
2. Wear appropriate clothing when
e:<emising; do not wear loose
clothing that could become
caught In the CARDIO FIT PLUS.
Always wear athletic shoes for
foot protection.
3. Keep small children and pets
away from the CARDIO FIT PLUS
at all times.
6.
.
.
g.
The resistance cylinder becomes
very hot during use. Allow the
resistance cylinder to cool
before touching it. Wheil adjust-
ing the resistance, touch only the
resistance adjustment collar.
The CARDIO FIT PLUS should
not be used by persons weighing
more than 250 pounds.
Do not use the CARDIO FIT
PLUS when the resistance cylin-
der is below room temperature or
damage may occur.
Always keep your back straight
when using the CARDIO FIT
PLUS. Do not arch yofir back.
4. After adjusting the position of
the seat, push on the seat to
make sure that the seat knob is
engaged in one of the holes in
the underside of the seat frame.
Do not use the CARDIO FIT
PLUS unless the seat is _ecurely
locked in position.
5. Before exercising, make sure that
the link arms are securely con-
nected to the upper or lower
rollers on the handlebar frame.
10.Use the CARDIO FIT PLUS only
as described in this manual.
WARNING: Before beginning this or
any exercise program, consult your
physician. This Is especially impor-
tant for persons over the age of 35
or persons with pre-existing health
problems. Read all instructions
before using. SEARS assumes no
responsibility for personal injury or
property damage sustained by or
through the use of this product.
ASSEMBLY
Place all parts of the CARDIO FIT
PLUS in a cleared area and remove the
packing materials. Do not dispose of
the pdcking materials until assembly is
completed. Read each step carefully
before beginning.
1. Raise the Handlebar Frame (7) to
the position shown. Hold the
Handle (20) and hook the Link
Arms (4) onto the lower Rollers
(33) on the Handlebar Frame.
Press two Round Endcaps (8)
onto the stabilizer at the front of
the Frame (6). Press two Round
Endcaps onto the stabilizer at the
rear of the Frame (not shown).
THE FOLLOWING TOOLS ARE
REQUIRED FOR ASSEMBLY:
The included pedal tool (_
A phillips screwdriver
A rubber mallet !--_}:a=_
L_J
Turn the Seat Knob (38) to loosen
it. Pull down the Seat Knob and
slide the Seat (3) onto the Seat
Frame (5). Slide the Seat to the
desired position and release the
Seat Knob. Retighten the Seat
Knob. Push on the Seat to make
sure that the Seat Knob is
engaged in one of the holes in
the underside of the Seat Frame.
3. Press the hvo Domed Endcaps (13'
• onto the upper end of the
Handlebar Frame (7).
Insert the Handlebar (2) into the
Handlebar Frame (7). The sides of
the Handlebar must bend toward
the Seat (not shown). Tighten the
four #8 x 1/2" Screws (16) into the
Handlebar Frame and the
Handlebar.
4.
5.
Connect the Sensor Wire (15) to th{
wire on the Monitor (1). Insert all
excess wire into the Frame (6).
Hold the Monitor (1) with both hands
and slide it down onto the Frame (6)
Refer to the inset drawing. Be sure
that the side of the Monitor is
behveen the Frame and the indicat-
ed 1/2" Dome Cap (29). Push the
1/2" Dome Cap against the side of
the Monitor.
Slide the Foam Pad (26) onto the
end of the 1/2" X 6 1/2" Axle (39).
Apply a small amount of grease to
the shaft on the right side of the
Pedal Frame (32). Slide a Pedal (12}
onto the shaft. Make sure that the
Pedal is turned so the plastic tube is
facing the Pedal Frame. Using the
included pedal tool, lap a 1/2" Push
Nut (30) onto the shaft. Make sure
that the Push Nut is turned as
shown in the inset drawing.
Attach the other Pedal (not shown)
in the same manner.
Note: Extra 1/2" Push Nuts (30) may
and the pedal tool in case replaceme
Note:The CARDIO FIT PLUS features
the nature of resistance cylinders, it i
neath the CARDIO FIT PLUS be cove