Extron electronics RGB 400 Series User Manual page 19

Specifications
Specifications, cont'd
These specifications apply to all models unless otherwise noted.
Video input
Number/type .............................. 1 analog RGBHV, RGBS, RGsB
Connectors .................................... 1 9-pin male D connector for MBC/LBC
Nominal level(s) .......................... Analog — 0.3V to 1.45V p-p
Impedance .................................... 75 ohms or HI Z, switchable (set to
Horizontal frequency ................. 15 kHz to 150 kHz (optimum 15 kHz to 62
Vertical frequency ....................... 30 Hz to 170 Hz
Return loss .................................... -30dB @ 5 MHz
Video throughput
Gain ............................................... Unity (0.7V), 15% with 3dB peaking
Bandwidth .................................... 300 MHz (-3dB)
Video output
Number/type/format ................ 1 analog RGBHV, RGBS, RGsB
Connectors .................................... 6 BNC female
Nominal level .............................. Analog 0.7V p-p, 0.8V p-p, or 0.9V p-p
Impedance .................................... 75 ohms
Return loss .................................... -30dB @ 5 MHz
Sync
Input type ..................................... Autodetect RGBHV, RGBS, RGsB
Output type .................................. RGBHV at all times
Input level .................................... 2.0V to 5.5V p-p with +0.2VDC offset
Output level ................................. 4.0V to 5.0V p-p
Input impedance ......................... 10 kohms
Output impedance ...................... 75 ohms
Max propagation delay .............. 50 nS
Max rise/fall time ....................... 2.5 nS
Polarity .......................................... Positive or negative
RGB 400 Series Specifications
A-2
cable or buffer
75 ohms if no local monitor is connected)
kHz)
(0.8V), 30% with 6dB peaking (0.9V)
(internal jumper-selectable) w/peaking
(accepts RGsB but does not strip from
video)
RGBS at all times
RGsB only when input is RGsB
max.
Audio input — RGB 402
Number/type .............................. 1 stereo, unbalanced (pass-through)
Connectors .................................... 2 RCA female jacks
Audio input — RGB 404
Number/type .............................. 2 stereo, unbalanced; 1.0Vrms (+4dBu),
Connectors ..................................... Ch. 1 ........... 2 RCA female jacks
Impedance .................................... 10 kohms, DC coupled
Minimum level ............................ 100mV
Maximum level ............................ +8.5dBu
Audio input — RGB 406 and RGB 408
Number/type .............................. 1 stereo, unbalanced; 1.0Vrms (+4dBu),
Connectors .................................... 3.5 mm stereo female jack (2 channel),
Impedance .................................... 10 kohms, DC coupled
Minimum level ............................ 100mV
Maximum level ............................ +8.5dBu
Audio throughput — RGB 404 (channels 1 and 2),
RGB 406 and RGB 408
Gain ............................................... Unbalanced 0dB, balanced +6dB
Response ....................................... ±0.5dB @ 20 Hz to 20 kHz
THD + Noise ................................ 0.03% @1 kHz, 0.3% @ 20 kHz at rated
S/N ................................................ >90dB, output 14dBu, balanced
Stereo channel separation .......... >95dB @ 1 kHz to 20 kHz
Audio output — RGB 402
Number/type .............................. 1 stereo, unbalanced
Connectors .................................... 1 pair solder cups
20 Hz to 20 kHz
Ch. 2 ........... 3.5 mm stereo female jack
(2 channel), unbalanced;
tip (L), ring (R),
sleeve (ground)
20 Hz to 20 kHz
unbalanced;
tip (L), ring (R), sleeve (ground)
maximum output drive
RGB 400 Series Specifications A-3