Table of Contents
Advertisement
[] Insertretractable
downdraftvent into countertop
cutout.Twopeopleare
recommended to supportthe
weight of the downdraftvent
duringlifting. Positiondowndraft
vent so it is centered in cutoutand
parallelto edgeof cutout.Check
that downdraftvent is vertical.Then
attachlowersupportlegsto cabinet
floor with screws.
When attaching
undercounter
bracket
to underside
of countertop,
make
sure that the screw length will not go
through
countertop
when tightened.
1 = Attach one undercounter
mounting
bracket on front upper
right corner of downdraft
vent
with slot over vent mounting
hole
and flange against countertop.
Attach other bracket to left side of
downdraft
vent. Carefully
drill
starter holes through
undercounter
mounting
brackets
into underside
of countertop.
Insert appropriate
length screws
into holes and tighten
brackets to
countertop.
Electrical
Shock Hazard
Disconnect
power before
servicing.
Connect ground wire to green
ground screw in terminal
box.
Failure to do so can result in
death or electrical shock.
2
= Disconnect
power.
vent box
knockout
\
green
ground
wire
___.
conduit
connector
o
wiring
box
cover
teen
screw
[] Feed the power supply
cable through
the conduit
connector
and into wiring
box.
Connect the white wires together
with a twist-on
wire connector.
Connect the black wires together
with a twist-on
wire connector.
Attach the green (or green and
yellow) ground wire to eyelet with
green ground
screw and tighten
screw. Replace wiring
box cover.
green
screw
ground
wire
-_//_"
ext eric r-too u nt ed
vent motor wiring
I
4=
Remove vent box
knockout and install conduit
connector.
Feed exterior-mounted
vent motor
wiring
through
conduit connector.
IMPORTANT: Do not wire the
exterior vent motor black and
white wires into the wiring
box.
Wires must be connected
as
shown. Connect the white wires
together with a twist-on
wire
connector.
Connect the black
wires together
with a twist-on
connector.
Attach ground wire to eyelet with
green ground
screw and tighten
screw.
Tighten conduit
connector
clamp
screws.
15=
Reconnect power.
microswitches
behind filters
ON/OFF
lower
ontrol
_filter or filters
depending
on
_
X
model
end cap
6_
Push and hold for a few
seconds the button on the top of
the downdraft
vent. Retractable
section of downdraft
vent will rise
and blower will start. Position the
top trim over the retractable
section and snap trim into place.
7=
Turn the control
knob on
side of vent to check the
operation
and speed of blower.
If blower
does not operate:
• Check that filter or filters are
pressed in as far as they will go.
Check that circuit
breaker is not
tripped
or house fuse blown.
Reconnect power. Check that
wire connections
have been
made correctly.
I
8[]
Connect vent to blower.
Position vent to avoid wall studs
and floor joists. Complete
all vent
work.
Use duct tape to sealall
joints.
Vertical vent for wall-
mounted
installations
should pitch
down slightly
toward the vent to
allow moisture
to run outside.
9=
Install cooktop
according
to manufacturer's
instructions,
Check that rear of cooktop
overlaps
edge of retractable
downdraft
vent
by 3/8" (9.5 mm).
To get the most
efficient
use from
your
new
retractable
downdraft
vent,
read the Use and Care
Information
section
on
page
12.
Keep Installation
Instructions
and Use and Care
Information
close by for
easy reference.
11
Advertisement
Table of Contents
