KitchenAid KUDC10FXSS2 User Instructions page 10

CONTROL PURPOSE COMMENTS
To start or iesUme a If the door is opened during a CYcle or the power is interrupted, the START/RESUME
wash cyc!e indicator flashes. The cycle wil! not resume until the door is closed and START/RESUME is
0_._L_, cyo,o pressed.
NOTE" If the START/RESUME button is located on tOP of door, push door firmly closed
Within 3 seconds of pressing START/RESUME. If the door is not closed within 3 seconds,
the start button LED wi!l flash, an audib!e tone wil! be heard, and the cyc!e wi!l not start.
To reset any cycle or
options during
selection.
To cancel a wash
cycle after it's
started.
Press CANCEL/DRAIN to reset any control selections made.
See "Canceling A Cycle After Dishwasher Is Started" and "Changing a Cycle After
Dishwasher is Started" sections.
To turn the audible Press and h01d the Hi Temp sCrub button foi3 seconds to tuin the audible tones on or off,
tones on or off, Only audible tones for confirming button Presses can be turned on/off, Important audible
_too, Q:,0!,:,_ tones, such as indicating a cyc!e has been interrupted, cannot be deactivated,
CONTROL PURPOSE COMMENTS
wo., ..... i................... The Cycle Status Indicator Clean indicator glows When a Cycle is finished.
• • " , Lghts are used to fo owthe ........
°. ..... !f you select the San] R_nse ophon, when the Sanl Rinse cycle _sfinished,
progress
OT
tne a snwasner
, , . ,., _. the Sanitized indicatorg!ows, lfY0urdishWasherdid not proper!ysanitize
cyc e Locatecl on iRe Tront
the di ;w Sl_er for front your dishes, the light flashes at the end of the cyclel This can happen if the
T
sn a
..... ; . , cycle is interrupted or the water could not be heated to the required
controJ mooe s ano iocateo "em erature
on the top of the door for ! P ,
hidden control models. The Clean and Sanitized lights go off when you open and close the door or
press CANCEL
A
The Front Indicator Light or
Single Exterior Light (A)
shows progress of your
dishwasher cycle by color.
(Available on some hidden
control models only).
The light will be blue if the dishwasher is washing or rinsing. The light will
be red when the dishwasher is drying. The light will be green to indicate
that the cycle is complete. If the Front Indicator Light is blinking, see
"Troubleshooting" section.
The Cycle Status Display is The indicators Wil! inform you if you are able to add a dish to the cycle afte[
used to follow the progress it has started. It wi!l also inform you if the dishwasher is washing, rinsing,
of the dishwasher cyc!el and drying, complete, and!0r sanitized, They will show whether the control is
to show other information, locked and/or the delay oPtion is selected. A series of bars wi!! count down
(Available on some models the duration of the cycle remaining from left to right. Each bar equals
instead of Cycle Status approximately 24 minutes of cycle lengthi The bars will als0 count down
Indicator Lights) the delay feature from !eft to right, and the de!ay indicator will be activated.
Canceling A Cycle
1. Open the door slightly to stop the cycle. Wait for the spraying
action to stop before completely opening the door.
2. Press CANCEL!DRAIN button once. The Cancel/Drain light will
light up.
3. Close the door and the dishwasher starts a drain cycle (if water
remains in bottom of dishwasher). Let the dishwasher drain
completely. The Cancel/Drain light turns off after 2 minutes.
Changing A Cycle After Dishwasher Is Started
1. You can interrupt a cycle and restart your dishwasher from the
beginning using the following procedure.
2. Open the door slightly to stop the cycle. Wait for the spraying
action to stop, then open the door completely.
3. Check that detergent dispenser cover is still closed. If cover is
open, you will need to refill the detergent dispenser before
restarting your new cycle.
4. Press CANCEL!DRAIN twice to reset the control.
5. Select new cycles and options.
6. Press START/RESUME.
Adding A Dish After Dishwasher Is Started
1. Check if Add a Dish indicator is lit. (Available on some models.
Otherwise, proceed to Step 2).
2. Open the door slightly to stop the cycle. Wait for the spraying
action to stop, then open the door completely.
3. Check whether the detergent dispenser cover is still closed. If
it is open, the wash cycle has already started and adding a
dish is not recommended.
4. If detergent has not yet been used (detergent dispenser cover
is closed), you may add a dish.
5. Press START/RESUME.
10