Advertisement
Message table (continued)
Indicators
The ON indicator,
LAMP indicator
and TEMP indicator
light or blink in the following
cases.
ON
indicator
Lights orange
Flashes green
Lights green
Flashes orange
LAMP
indicator
Turns off
Turns off
Turns off
Turns off
TEMP
indicator
Turns off
Turns off
Turns off
Turns off
Message
Processing
Standby status
Warming up
Operation status ,1
Cool down
Wait some time (approx. 20 min.) before
Lights red
Lights red
Turns off
The lamp does not light. *2 turning the power on again, If the
indicator still lights, the lamp may have
failed and. Replace with a new lamp.
Lights red
Flashes red
Turns off
A lamp has not been inserted Firmly insert the lamp as far as possible
or the lamp cover is missing,
and screw the lamp cover in place,
Lights red
Turns off
Flashes red
The coolingfan is not operating. Contact your dealer,
Flashes red
Flashes red
Turns off
The total lamp time has
Contact your dealer,
exceededthe replacementtime.
When the LAMP or TEMP indicator lights or flashes, turn off the MAIN POWER switch before proceeding.
If the problem still persists, contact your
dealer or service company.
*1: When the cooling fan is stopped and the interior becomes overheated, the power will tam off automatically
to allow cooling (the indicator will turn
off). In such cases, turn offthe projector power, allow the set to cool and then tam the projector power on again. The lamp will then ligN. If the lamp
does not light, contact your dealer or service company.
*2: In some cases, when the air holes becomes blocked and the interior temperature
rises, the lamp will be turned off for protection and the LAMP
iMicator will flash red. In such cases, turn offthe MAIN POWER switch, allow the set to cool (for approx. 20 min.) and then turn the power on again.
When you think something wrong
Before requesting
repair, check in accordance
with the following
chart. If the situation cannot be corrected,
then
contact your dealer.
Symptom
Possible cause
Remedy
Page
The power is not
,The main power switch is not turned on.
,Tom on the main power switch.
P.13
turned on.
,The power cord is disconnected.
,Plug the powercord into an AC poweroutlet.
P.9
No video or audio.
,The input is not correctly set.
,Use the projector or remote control to set.
P.8.10,
13,19
•No signal input.
,Connect correctly.
P.9.31
Video is present but
,The projector is not correctly connected.
,Connect correctly.
P.9.31
no audio.
,The volume is seet to minimum.
,Press VOLUME + on the remote control or display
P.10.18
the menu screen and adjust the volume.
•Mute is turned on.
,Press the MUTE button.
P.8.10
Audio is present but
,The projector is not correctly connected.
,Connect correctly.
P.9.31
no video.
,The brightness adjustment knob is rotated
,Select BRIGHT with the MENU button and then
P.17
fully clockwise,
press the ((_)
key.
•The lens cap is still on.
,Remove the lens cap.
P.13
Colors are pale and
Color density and color matching are not
Adjust the video.
P.18
colormatching is poor.
correctly adjusted.
Images are dark.
,Brightness and contrast are not correctly
,Adjust the video.
P.18
adjusted.
•The lamp is nearing the endof its servicelife.
,Replace with a new lamp.
P.32
Video is blurred.
Focus or H PHASE is out of adjustment.
Adjust the focus or H PHASE.
P.13.18
The LAMP indicator
Lamp failure.
Wait approximately 20 min. and then turn the
P.33
lights red.
power on again.
The TEMP indicator
Internal overheating.
,Make surethe ventilation openingsare not blocked.
P.31.32
lights red.
,Clean the air filter.
•Lowerthe ambient t emperature to 35degreesC or less.
A
bright
dot may be seen in the
picture.
This is a
phenomenon
peculiar
to the
liquid crystal
and is not a
problem.
33
Advertisement
