Advertisement
Names and functions of each part (continued)
Remote control transmitter
VIDEO, RGB button F
\
Press to switch the input. (Refer to page 13, 19.)
STANDBY
/ ON
button
Used to turn the power on and off.
Press for 1 sec. or more to turn the power off
(enter standby status).
(Refer to pages13 and 14.)
DISK
PAD
(1) Used to select menu items when the menu
screen is displayed
(refer to page 16-18).
(2) When the menu is not displayed,
the mouse
shift function and left click function are active.
"I
(3)After
the
POSITION
button
has
been
pressed,
the screen can be moved upward,
downward and
ght.
MENU
button
Used to turn the menu screen display on and off.
(refer to page 17-21).
MAGNIFY
button
Used to magnify the displayed =mage.
P in P button *2
Used to turnP in P (PictureIn Picture:displays sub video
signal images in the RG8 signal) on and off.
Each time this button is pressed, operation will change in
the following sequence:
(1)
(1)- (3)
t
BLANK
button
Used to turn blanking on and off,
(Refer to page 20,)
FOCUS
button
Used to adjust the focus of the image on the
screen. (Refer to page 13,)
VIDEO
Y
LASER
button
Turns the laser beam on and off. Refer to page
11 cocneming usage and observe the cautions.
POSITION
button
Pressingthe top, bottom, left or right of Disk Pad
after pressing this button causes corresponding
movement (effective only for RGB signal output).
RESET
MOUSE
/ RIGHT
button
(1)Operates as the RESET batten when the menu
is displayed.
Press this button to return to the
initial settings,
(2)Used to click the right mouse button when the
menu is not displayed (refer to page 25,26).
(3)Pressing this button after scrolling the screen
with POSITION returns the screen to the original
position.
FREEZE
button
Used to turn the freeze (still) image display on
andoff.
VOLUME button
Adjusts the volume of the sound. Press [/\]
to
increase the volume and ( y/ ) to decrease the
volume.
MUTE button
Mutes the sound when pressed and restores the
sound when pressed again.
TIMER
button
Turns the time display of the timer displayed
on
the menu screen on and off.
The timer is not displayed during blanking.
Refer to page 20, 21 concerning
the method
used to set the timer.
Used to adjust the size of the image. (Refer to
page 13.)
AUTO
button
Used to execute auto-adjust.*3
*i
POSITION
icon
When
the POSiTiON
button
is pressed,
the remote
control
buttons will light and the moving display icon will appear at the
bottom dght of the screen.
*2
With the P in P function,
signals
are input to both RGB and
VIDEO.
This function
operates
only when the RGB signal has
been selected. There is no display in the case of the no signal and
when the RGB signal is outside the sync range.
When P in P is used, audio is automatically switched to video.
In P in P, audio input can be switched by pressing the VOL /\and
VOL Y/keys
of the remote control, displaying
the audio bar and
moving Disk Pad left and right during the display.
u_ _
RGB/VIDEO
10
*3 Auto adjustment
function
The projector automatically adjusts 4 items (V, POSIT, H, POSIT,
H. PHASE, H. SIZE).
When you choose AUTO (move the cursor to the right from the
manual operation
position),
the AUTO confirmation
menu shown
below is indicated.
• Auto adjust requires several tens of seconds.
• Auto adjust may not operate correctly in some cases
depending on the computer connected and the signal.
• Auto adjust may not operate correctly
in some case:
depending on the type of image.
• Execute auto adjust with the display ot" the applicafior
being run by the computer at maximum.
• After auto adjust, the image may be slightly dark in
some cases due to automatic
adjustment
of the signal
level.
• AutO adiust canot execute when the initial display is
"NO INPUT IS DETECTED"
or "SYNC IS OUT OF
RANGE" during FREEZE or MAGNIFY.
Advertisement
