Advertisement
ERectronic Controlts (oomin ed)
Automatic
Oven Timer
The oven timer will automatically
start and stop your oven cooking or'
self=cleaning operation
for you
For automatic
oven cooking:
1, Push COOK TIME. button
2, Turn SET knob to set length
of' baking time
3. Push BAKE button
4. Turn SET knob to set desired
temperature.
When cook time is reached,
the End-of-Cycle
Tone (3 long
beeps) wilt sound and the oven
wilt turn off.
During
automatic
cooking:
* You can push the STOP TIME
button to find out when tile End-
of=Cycle Tone (3 long beeps) will
sound and the oven wilt turn off
o You can push the CLOCK
button
to display time of day without
cancelling
the oven operation
To Delay Starting an
Automatic Oven Operation
If a delayed
cooldng operation
is desired:
1. Push COOK TIME button
2. Set length of baking time with
SET l,:not>
3. Push STOP TIME button.
4, Turn SET knob to time of day
when baking should be completed
Do not set a stop time that is less
than the length of cooking time
plus the current time of day
5. Push BAKE, button
6, Turn SET knob to desired
temperature,
When stop time is reached,
the End-of=Cycle
Tone (3 long
beeps) wilt sound and tile oven
will turn off
Caution:
Never let food sit in the
oven tbr more than t hour betbre
cooldng starts. Room temperature
is ideal for the growth of harmful
bacteria, Be sure oven light is off
because heat fl'om the bulb will
speed bacteria growth
Note: You can push the STOP
TIME button to find out when the
oven will turn off. Push and hold
the COOK TIME button to find
out when the oven wilt turn on..
ff a delayed
self-cleaning
oven
operation
is desired,
see page 21.
How to Change
a Program
When a function has been
entered, you can recall what
has been programmed
by
pushing the corresponding
function button. The messages
in the display show you which
function is currently being
displayed. While the function
is displayed, you can change it
with the SET knob. You can
change any programmed
function at any time.
Tones
Endmf-Cycle
Tone (3 long beeps_
one second on, one second off):
shows that a timed oven operation
has reached STOP TIME or"that
the Minute/Second
Timer has
counted down..
Attention
Tone (series of short
beeps, t/4-second
on, 1/4-second
off, until proper response
is given):
will sound if oven has only been
partially programmed
For
example, if you have selected a
cook time but no temperature,
you
will hear' the Attention
Tone until
you select a temperature
or' push
CANCEL,,,
Notification
Tone (single, one-
second beep): indicates oven has
stabilized
at selected temperature.
Key 'lone (single, 1/10-second beep):
sounds when any button is pushed
Function
Error
Tone (series of
very rapid beeps, 1/8-second
on,
l/4-second
off): display will show
a failure code. Cancel Function
Error Tone by pushing
the
CANCEL
button. If the Function
Error Tone starts again (after about
i5 seconds), call for' service,,
Disconnect
the range electrical
supply to stop the tone,,
If tile function en"or occurred
while
you were programming
the
Electronic
Control, push the
CANCEL.
button and try again.,
To Cancel the Tone...If
you don't
want an audible tone when you
push a button, you can eliminate
the Key Tone by pushing and
holding the CANCEL, button
until you hear a short beep
(in approximately
two seconds),
To activate the tone again, push
and hold the CANCEL
button once
more until you hear a short beep,
Cancelling
or activating
the tone
should only be done when there is
no oven operation
programmed
Pushing the CANCEL
button will
clear all functions
except the Clock
and Minute/Second
Timer'.
11
ra_
Qr_
_m
¢3
Advertisement
