GE DBL333 Owner's Manual And Installation Instructions page 17

3-Wire System for Electric Dryers-DO NOT use for Mobile Home Installations
_] Remove the screws securing the temfinal block
access cover and the strain relief mounting
bracket located on the back of the duer
upper corner.
V_ Attach the power cord neuu'al (center _4re)
conductor to the silver-colored center terminal
on the terminal block. Tighten the screw
securely.
[2-_Install a UL-approved su'ain relief into the power
cord entry"hole of the mounting bracket. Use
a su'ain relief which attaches to the mounting
bracket with a nut. Finger-tighten the nut only
at this time.
Vj] Thread a UL-approved 30A, 240V, 3 #10 AWG
minimum copper conductor power cord through
the strain relief.
Green gl
Silverterminal
_] Attach the remaining two power cord outer
conductors to the ol{ter brass-colored temnnals
on the terminal block. Tighten both screws
securely.
WARIVING:Do not make a sharp bend or crimp
wiring/conductor at connections.
_-] Reattach the su'ain relief mounting bracket to
the back of the dryer _4th two screws" Tighten
screws securely.
[--_ Tighten the f_steners securing the cord restraint
firl'nly against the power cor&
Green neutral
gr°undwire _//__ _/"(\ Nu_
_/'/"'%lighten nut to
thesethreads
Use copper Strain elief Po_wercord
conductors only. mounting bracket
[_ Tighten the strain relief nut securely so that the
strain relief does not turn.
V_ Reinstall the temnnal block access cover.
4-Wire System for Electric Dryers--MUST be used for Mobile Home Installations
[7] emove the screws securing the temfinal block
access cover and the strain relief mounting
bracket located on the back of tim dtTer
upper corner.
[_-] Install a UL-approved smtin relief in the enuy
hole of the mounting bracket. Use a strain relief
which attaches to the mounting bracket with a
nut. Finger-tighten the nut only at this time.
V_] Remove the green neutral _'ound _4re from
the _een _ound screw located at)ove the
temfinal block.
Typical 4
conductor| | | ]
receptacle_J
Black240V
Typical
,_- White neutral
4 conductor c ord_
_,_ Red240V
" Green ground
V_ Thread a UL-approved 30A, 240V, 4 #10 AWG
minimum copper conductor power cord fllrough
the strain relief.
_ ttach the _een power cord ground wire to the
cabinet with the _'een _'ound screw.
_-] Attach the white (neuu'al) power cord conductor
fi'om the power cord and the green ground _4re
fi'om the dryer harness to the silver-colored
center terminal on the terminal block. Tighten
the screw securely.
V-_ Attach the red and black power cord conductors
to the outer bra_ss-colored terminals on the
temfinal block.
Green power cord ground wire
Green ground _ /
screw Silverterminal
_'__'_J_ _._Terminal block
Greenneutral _ __'_,
ground wire mJ_,_)'S/_i_ --'_'_ Black
Red !,,,,,,____['/_White / Nut lighten nutto
_!_ _, _i¢'_ these threads
//..,. ,J/// Strain_._
'/'_" _ relief T .Y"/_&
Powercord / _ [nounting [_)_ "_
bracket
WARNING:Donot make a sharp bend or crimp
wiring/conductor at the connections.
_-] Tighten the fasteners securing the cord
restraint firmly against the p[)wer cord.
_-_ Tighten the strain relief nut securely so the strain
relief does not tuna.
-0]Reinstall the terminal block access cover.
17