Zoom B3 Operation Manual page 44

Effect Types and Parameters
074 MonoSyn
075 StdSyn
076 SynTlk
077 V-Syn
078 4VoiceSyn
079 Z-Syn
080 Z-Organ
44
This effect produces the sound of a monophonic (single-note playing) bass synthesizer that
detects the pitch of the input signal.
Knob1
Decay 0–100
Page01
Adjusts the rate of sound change.
Synth 0–100
Page02
Adjusts level of synthesizer sound.
ZOOM original bass synthesizer sound.
Knob1
Sense 0–100
Page01
Adjusts the sensitivity for trigger
detection.
Synth 0–100
Page02
Adjusts level of synthesizer sound.
This effect produces a synthesizer sound similar to a talking modulator producing vowels.
Knob1
Decay 0–100
Page01
Adjusts the rate of sound change.
Synth 0–100
Page02
Adjusts level of synthesizer sound.
This effect produces a vintage bass synthesizer sound.
Knob1
Decay 0–100
Page01
Adjusts the rate of sound change.
Synth 0–100
Page02
Adjusts level of synthesizer sound.
This effect type adds synthesizer harmony components to single notes played on the
bass. The harmony components are determined by the Mode and Scale parameters.
Knob1
ATTCK 0–10
Page01
Adjusts the attack rate of the synthesizer
sound.
Synth 0–100
Page02
Adjusts level of synthesizer sound.
This bass synthesizer sound adds analog synth fatness.
Knob1
Wave Saw, Sqr
Page01
Selects the waveform.
Freq 0–10
Page02
Sets the cut-off frequency of the low-
pass filter.
Synth 0–100
Page03
Adjusts level of synthesizer sound.
This effect simulates an organ sound.
Knob1
Upper 0–100
Page01
Adjusts volume of high frequencies. Adjusts volume of low frequencies.
HPF 0–10
Page02
Adjusts high-pass filter cutoff frequency. Adjusts low-pass filter cutoff frequency. Adjusts the output level.
Knob2
Saw, Pulse,
Wave
PWM
Sets the waveform type to "Saw"
(sawtooth), "Pulse" (square wave),
or PWM (pulse width modulation
resulting in fatter sound).
Dry 0–100
Adjusts level of original sound.
Knob2
Sound 1–4
Selects a synthesizer variation.
Dry 0–100
Adjusts level of original sound.
Knob2
Type iA, UE, UA, oA
Selects a vowel variation.
Dry 0–100
Adjusts level of original sound.
Knob2
Sense 0–30
Adjusts the sensitivity for trigger
detection.
Dry 0–100
Adjusts level of original sound.
Knob2
Mode 1–9
Selects a harmony type from 1 - 9.
(See Table 4)
Dry 0–100
Adjusts level of original sound.
Knob2
Decay 0–100
Adjusts the speed of tone modulation. Adjusts the tone.
Range 0–20
Adjusts the amount of cut-off frequency
modulation.
Dry 0–100
Adjusts level of original sound.
Knob2
P Lower 0–100
LPF 0–10
Knob3
Reso 0–10
Adjusts the intensity of the effect
character.
P Level 0–150
Adjusts the output level.
Knob3
Tone 0–10
Adjusts the tonal quality of the sound.
P Level 0–150
Adjusts the output level.
Knob3
Tone 0–10
Adjusts the tonal quality of the sound.
P Level 0–150
Adjusts the output level.
Knob3
Range -10–10
Adjusts the filter shift range.
P Level 0–150
Adjusts the output level.
Knob3
Scale 1, 2
Selects a harmony variation. Two
variations are available for each of
the 1-9 modes. (See Table 4)
P Level 0–150
Adjusts the output level.
Knob3
P Tone 0–10
Reso 0–20
Adjusts the intensity of the filter
resonance.
Level 0–150
Adjusts the output level.
Knob3
Dry 0–100
Adjusts level of original sound.
Level 0–150