Advertisement
Quick Links
Installation and Assembly:
Flat Panel Pull-out Swivel Wall Mount for 26" - 58"
Screens
Models: SP 850, SP 850P, SP 850-S, SP 850P-S
3215 W. North Ave. • Melrose Park, IL 60160 • (800) 729-0307 or (708) 865-8870 • Fax: (708) 865-2941 • www.peerlessmounts.com
This product is intended for use with UL
Listed products and must be installed by a
qualified professional installer.
R
Max Load Capacity: 150 lb (68 kg)
ISSUED: 10-12-05 SHEET #: 202-9038-6 05-19-07
Advertisement
Related Manuals for PEERLESS SP 850
Summary of Contents for PEERLESS SP 850
- Page 1 Installation and Assembly: Flat Panel Pull-out Swivel Wall Mount for 26" - 58" Screens Models: SP 850, SP 850P, SP 850-S, SP 850P-S This product is intended for use with UL Listed products and must be installed by a qualified professional installer. Max Load Capacity: 150 lb (68 kg) 3215 W.
-
Page 2: Table Of Contents
Note: Read entire instruction sheet before you start installation and assembly. WARNING • Do not begin to install your Peerless product until you have read and understood the instructions and warnings contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, please call Peerless customer care at 1-800-729-0307. -
Page 3: Parts List
Parts List SP850 SP850P SP850-S SP850P-S Description Qty. Part # Part # Part # Part # wall mount assembly 201-0385 201-0386 201-0383 201-0384 locking tab 200-1871 200-1871 200-4871 200-4871 .219 ID x .5 OD x .125H spacer 540-1032 540-1032 540-1032 540-1032 #14 x 2.5"... -
Page 4: Installation To Wood Stud Wall
Installation to Wood Stud Wall WARNING • Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components. Using a stud finder, locate the edges of the wood studs used in mounting this product. Use of an edge-to-edge stud finder is highly recommended. -
Page 5: Installation To Solid Concrete And Cinder Block
Installation to Solid Concrete and Cinder Block Wall WARNING • When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" of actual concrete thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid part of the block, generally 1"... -
Page 6: Mounting Flat Panel Screen With Vesa Hole Pattern
Place installation tab over sliding arms of wall mount assembly (A) to lock them in place. INSTALLATION TAB SLIDING ARM FOR INSTALLING TO VESA 100 MM, 200 MM HOLE PATTERN WARNING • If screws don't get three complete turns in the screen inserts or if screws bottom out and adapter plate is still not tightly secured, damage may occur to screen or product may fail. -
Page 7: Mounting Flat Panel Screen With Peerless Plp Model Adapter Plate (Plp Adapter Plates Are Not Ul Listed)
FOR VESA 200 MOUNTING PATTERN: Thread two M4 x 12 mm screws (BB), leaving .25" exposed thread, into top holes on back of screen. Hook screen onto mounting plate, and attach using two bottom M4 x 12 mm screws as shown in figures 4.3 and 4.4. Tighten all four screws. - Page 8 Slide one mesh sleeve (F) over each cable. Use Optional: To lock mount in closed position, insert cable ties (G) to tighten both ends of mesh sleeves one M5 x 40 mm screw (DD) into tapped hole in to cables. either top or bottom of flat plate.
- Page 9 Roll can be adjusted 1° clockwise or Optional: To lock one sliding arm of mount in place, counterclockwise. slide locking tab (B) over top or bottom of sliding arm and attach to mount using one M5 x 10 mm screw To adjust roll, loosen screen fasteners slightly, (AA) and one spacer (C).
-
Page 10: Screen Compatibility Chart
Samsung 26" LT-P266W Sceptre 30" X30SV- Naga III 10 of 10 ISSUED: 10-12-05 SHEET #: 202-9038-6 05-19-07 © 2007, Peerless Industries, Inc. All rights reserved. All other brand and product names are trademarks or registered trademarks of their respective owners.