3 horsepower, 21 inch single stage, auger propelled snowthrower, electricstart (47 pages)
Summary of Contents for Craftsman 536.882092
Page 1
120 V.A.C. 12 AMP. 60 Hz. Double Insulated 20" Clearing Width ELECTRIC SNOW THROWER MODEL NO. 536.882092 Caution: Read and follow all Safety Rules and Operating Instructions before first use of this product. SEARS, ROEBUCK AND CO., Hoffman Estates, IL 60179 U.S.A. F-001126M...
Page 2
ORDERING/SERVICE LIMITED ONE-YEAR WARRANTY ON CRAFTSMAN SNOW THROWER For one years from the date of purchase, when this Craftsman Snow thrower is maintained, lubricated, and tuned up according to the operating and maintenance instructions in the owner's manual, Sears will repair, free of charge, any defect in material or workmanship.
Page 3
ty precautions. It means: "Attention! Become Alert! Your WARNING: Look for this symbol to point out important safe- Safety Is Involved." Check shear bolts and other bolts fre- quently for proper tightness to be sure the power cord to prevent acciden- WARNING: Always disconnect snow thrower is in safe working condition.
Page 4
dancewith the special instructions for shown in the assembly section of this manual. such use provided in this manual. 11. Never operate the snow thrower near REPAIR/ADJUSTMENTS SAFETY glass enclosures, automobiles, window After striking a foreign object, stop the en- wells, drop--offs, and the like without prop- gine (motor), disconnect the cord on elec- er adjustment...
Page 5
ASSEMBLY TOOLS REQUIRED FOR ASSEMBLY 1 - Knife to cut carton. CONTENTS OF PARTS BAG 1- Pliers 1 - Owner's Manual The figure below shows the snow thrower 1 - Warranty Card completely assembled. 1 - Parts Bag References to the right or left hand side of the snow thrower are from the viewpoint of (Not shown actual size) the operator's...
Page 6
TO ASSEMBLE rod bracket while inserting the worm into THE CHUTE CONTROL the notches in the discharge chute rota- tion ring. 1. Cut tie holding chute control rod to brack- Place wave washer and flat washer onto worm end of chute control rod. 2.
Page 7
KNOW YOUR SNOW THROWER READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR SNOW THROWER. Compare the illustrations with your SNOW THROWER to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference. Control Switch Lever Upper Handle...
Page 8
TO USE AUGER PROPEL ACTION 1. Squeeze the control switch lever down 2. To propel forward, raise the handle to al- against the upper handle to allow the au- low the auger blades to contact the ger to turn. ground (See Figure 5). equipped with a protector that WARNING: The motor is will disconnect...
Page 9
NOTE: Keep the second key (found in plas- 3. To operate snow thrower turn key (clock- wise) and hold in UNLOCKED position tic bag) in a safe place. while pulling control switch lever toward 4. To stop snow thrower, release lever on handle.
Page 10
WET PACKED SNOW hind snow thrower (operator's WARNING: Always stand be- Move slowly into snow of this condition. The position) when starting motor. greater the depth, the slower you should go. Do Not put hands, feet, hair or loose When it appears that the wet, packed snow clothing on near the discharge chute de- is causing the auger to slow down and the flector or auger housing while the motor...
Page 11
CUSTOMER RESPONSIBILITIES SERVICERECORDS After First Begin Before Each Fill in dates as you SERVICEDATES Season completeregularservice. Needed Hours Storage Tighten All Screws & Nuts ",,J Check Drive Belts Lubricate Chute Control Flange GENERAL RECOMMENDATIONS • Tighten any loose fasteners. The warranty on this snow thrower does not AFTER EACH USE cover items that have been subjected to op- erator abuse or negligence.
Page 12
TO ADJUST THE CHUTE CRANK ASSEMBLY If you cannot rotate the chute crank fully to the left and to the right, you need to adjust the chute crank (see Figure 9). 1, Loosen both 1/2" nuts, using 1/2" wrenches, on the crank adjusting brack- 2.
Page 13
TO ADJUST THE MOTOR PULLEY Reinstall belt cover. Make sure the short- er screw is in the front position (see 1. Loosen the two set screws on the motor Figure 10). pulley. 5. If the drive belt is damaged or worn ex- 2.
Page 14
MOTOR SERVICE Motor repairs and adjustments should be done by technicians trained to work on snow thrower type motors. Take your snow throw- er to an Authorized Sears Service Center for repair and adjustment. SNOW THROWER STORAGE Store the extension cord with the snow Thoroughly clean the snow thrower.
Page 15
CORRECTION TROUBLE CAUSE Have the unit serviced by a Motor runs erratically Damaged motor competent repairman. Remove obstruction. Obstruction in auger Clean auger housing. Clean ice and snow from discharge chute. Excessive vibration Stop motor immediately and Loose parts unplug power cord. Tighten all bolts and make all necessary repairs.
Page 25
For the repair or replacement parts you need delivered directly to your home Call 7am-7pm, 7days a week 1-800-366-PART (1-800-366-7278) Para ordenar piezas con entrega a domicilio - 1-800-659-7084 For in-house major brand repair service Call 24 hours a day, 7days a week 1-800-4-REPAIR (1-800-473-7247) Para pedir servicio de reparaci6n a...