How do I start my Craftsman 247.770550 yard vacuum?

To start your Craftsman 247.770550 yard vacuum, follow these steps:Attach the spark plug wire and rubber boot to the spark plug.Ensure the bag/chute switch button is fully depressed by the front tab on the bag handle or blower chute.Verify the bag/chute switch wire is connected to the engine and grounded to the mounting bracket.Fill the gas tank to 3/4 full or completely.Move the throttle control lever to the START/RUN (Rabbit) position.Move the choke control toward the throttle control to choke the engine's carburetor. A warm engine may not require choking.While standing behind the unit, grasp the starter handle and pull the rope out until you feel a drag.Pull the rope with a rapid, continuous, full arm stroke. Allow the rope to rewind slowly.Repeat pulling the rope if necessary until the engine starts. Once it starts, gradually move the choke control away from the throttle control. 1If the engine falters, move the choke control back toward the throttle control and repeat steps 7-1 Always keep the throttle control in the START/RUN position when operating the Yard Vacuum.

What should I do if my Craftsman 247.770550 yard vacuum won't start?

If your Craftsman 247.770550 yard vacuum won't start, consider the following:Fuel Issues: If the fuel tank is empty or contains stale fuel, fill it with clean, fresh gasoline. Note that fuel will not last over thirty days unless a fuel stabilizer is added.Spark Plug Connection: If the spark plug wire is disconnected, connect it to the spark plug.Recoil Cord Obstruction: If you cannot pull the recoil cord, there might be an obstruction lodged in the impeller. Disconnect the spark plug wire and remove the lodged object.Choke Position: Ensure the choke is in the ON position.Spark Plug Condition: If the spark plug is faulty, clean, adjust the gap, or replace it.Safety Switch: The safety switch must be depressed by the front tab on the bag handle when securing the bag. If the safety switch wire is not connected to the engine or not properly grounded, connect it to the engine connector and ground it to the mounting bracket. For more information, see page 18 of the manual.

How do I clear a jam or clog in my Craftsman 247.770550 yard vacuum?

To clear a jam or clog in your Craftsman 247.770550 yard vacuum, follow these steps:General Safety Procedure: Shut the engine off. Wait until all moving parts have come to a complete stop. Disconnect the spark plug wire and ground it against the engine. Never attempt to unclog the feed intake or discharge opening while the engine is running. If the discharge area becomes clogged: Stop the engine. Make certain the chipper shredder vacuum has come to a complete stop. Disconnect and ground the spark plug wire to the retaining post. Remove the vacuum bag or blower chute to gain access to the flail screen. Remove the self-tapping screw on the right side of the unit that attaches to the flail screen. Remove the hex screw on top of the rear housing near the mounting bracket and the flange lock nut that secures the flail screen. Remove and clean the screen by scraping or washing with water. Reinstall the screen. If a foreign object is lodged in the impeller: After performing the general safety procedure, remove the lodged object.

How do I assemble the Craftsman 247.770550 yard vacuum?

To assemble your Craftsman 247.770550 yard vacuum, follow these steps:Disconnect Spark Plug: Before proceeding, disconnect the spark plug wire from the spark plug and ground it onto the retaining post on the engine to prevent accidental starting.Attach the Handle:Remove the hairpin clips, carriage screws, and wing nuts from the lower handle.Place the bottom holes in the lower handle over the pins on the handle brackets and secure with hairpin clips.Insert carriage screws through the upper hole in the lower handle from the inside and secure with wing nuts.Unfold the upper handle until it aligns with the lower handle, ensuring the rope guide is on the right side of the upper handle.Make sure the cables are routed outside the lower handle and are not crimped.Secure the two handles by tightening the handle knobs.Pull the two cable ties attached to the cables tight (approximately 8 inches from each end) and place the cables into the cable guide.Loosen the wing nut that secures the rope guide, pull the starter rope out of the engine slowly and slip it into the rope guide, then tighten the wing nut.Attach the Hose Assembly:Slide the hose adapter of the hose assembly into the base adapter located on the left front of the Yard Vacuum.Pull the spring loaded pin out on the base and align the pin with the first hole (closest to the end of the tube) in the hose adapter, then release the pin to lock the hose in place.Snap the hose handle first into the upper hose handle bracket and then into the lower hose handle bracket.Lay the hose tubing on the hanger bracket next to the chipper chute.Attach the Bag:Grasp the bag handle with one hand and slide the locking rod on the mounting bracket with the other hand toward the engine, using the end of the mounting bracket as leverage.Slip the bag over the rim of the discharge opening and release the locking rod to secure the bag in place.Snap the bag clip to the top of the lower handle.Place the lower straps on the bag over the top of the lower handle, hooking them on the studs.Ensure the bag/chute switch button attached to the mounting bracket is fully depressed by the front tab on the bag handle when securing the bag, or the engine will not start.Attach the Blower Chute (if applicable):The bag must be removed before installing the blower chute.Grasp the blower chute with one hand and slide the locking rod on the mounting bracket with the other hand toward the engine, using the end of the mounting bracket as leverage.Slip the blower chute over the rim of the discharge opening and release the locking rod to secure the chute in place.Raise the nozzle height to the highest setting when using the blower chute.Ensure the bag/chute switch button attached to the mounting bracket is fully depressed by the front tab on the blower chute, or the engine will not start.

Why is my Craftsman 247.770550 yard vacuum losing suction?

Your Craftsman 247.770550 yard vacuum may be losing suction due to:Loss of power or erratic operation:A loose spark plug wire: Connect and tighten the spark plug wire.The unit running on CHOKE: Move the choke lever to the OFF position.A blocked fuel line or stale fuel: Disconnect the fuel line at the carburetor to drain the fuel tank, then fill with clean, fresh gasoline.Water or dirt in the fuel system: Disconnect the fuel line at the carburetor to drain the fuel tank, then refill with fresh fuel.The carburetor being out of adjustment: Contact your Sears Parts & Repair Center.Low engine RPM: Always run the engine at full throttle.Unit does not discharge:A clogged discharge area: Stop the engine, disconnect the spark plug wire, and clean the flail screen and inside of the discharge opening.A foreign object lodged in the impeller: Stop the engine, disconnect the spark plug wire, and remove the lodged object.Low engine RPM: Always run the engine at full throttle.A full vacuum bag: Empty the bag. For more information, see page 18 of the manual.

How do I effectively use the leaf vacuum function on the Craftsman 247.770550?

You can effectively use the leaf vacuum function in two ways:Using the Nozzle Vacuum: Place the nozzle/hose vac handle in the top position on the nozzle. Ensure the spring loaded pin is in the first hole (closest to the end of the tube) of the hose adapter. Place both hands on top of the upper handle to push the unit over yard waste. Adjust the nozzle height according to yard conditions. Raise the nozzle for thick layers of leaves or when operating with the blower chute, and lower it for smoother surfaces. Using the Hose Assembly: Place the nozzle/hose vac handle in the bottom position on the nozzle to redirect vacuum to the hose assembly. The spring loaded pin must be in the second hole of the hose adapter. Unhook the hose from the upper and lower hose handle brackets and grasp the hose handle to guide it while vacuuming yard waste in hard-to-reach places.

How do I clean or empty the collection bag on the Craftsman 247.770550 yard vacuum?

To clean or empty the collection bag:To empty the bag: Unhook bag straps from the lower handle and unsnap bag clip from the top of the lower handle. Grasp the bag handle with one hand and pull the lock rod on the mounting bracket with the other hand toward the engine to release. Lift the bag off the back of the unit. Twist the two buttons on the back of the bag to unlock and empty its contents. Hold the bag handle and bag clip while emptying the contents. To clean the bag: Wash the bag periodically with water. Allow it to dry thoroughly in the shade.

How do I switch between vacuum and blower modes on the Craftsman 247.770550?

To switch between vacuum and blower modes:For vacuum mode:To vacuum through the nozzle, place the nozzle/hose vac handle in the top position on the nozzle. The spring loaded pin must be in the first hole of the hose adapter.To vacuum with the hose assembly, place the nozzle/hose vac handle in the bottom position on the nozzle to redirect vacuum to the hose assembly. The spring loaded pin must be in the second hole of the hose adapter.For blower mode:Remove the vacuum bag.Attach the blower chute to the unit.Raise the nozzle height to the highest setting when using the blower chute.The bag/chute switch button attached to the mounting bracket must be fully depressed by the front tab on the blower chute for the engine to start. For more information, see pages 9, 11 and 12 of the manual.

What type of fuel does the Craftsman 247.770550 yard vacuum use?

The Craftsman 247.770550 yard vacuum uses clean, fresh, unleaded regular gasoline only. Do not use gasoline containing METHANOL. In general, fuel should be used within 30 days of its purchase date, as gasoline that has been sitting for any period longer than four weeks should be considered stale.

Does the Craftsman 247.770550 yard vacuum also mulch leaves?

Yes, the Craftsman 247.770550 yard vacuum is designed to shred material. Yard waste such as leaves and pine needles can be vacuumed up through the nozzle for shredding, and the shredded material is collected in the bag. The material is shredded by the flail blades on the impeller assembly. Do not attempt to shred or chip any material other than vegetation found in a normal yard.

Craftsman 247.770550 Operator's Manual

6.0 horse power yard vacuum

Hide thumbs Also See for 247.770550:

Operator's manual (40 pages)

Table Of Contents

Table of Contents

Quick Links

Operator's Manual

MRN°I

6.0 Horse Power

YARD VACUUM

Model No. 247.770550

CAUTION:

Before using

this product, read this

manual and follow all

Safety Rules and

Operating

Instructions.

•

Safety

•

Assembly

•

Operation

•

Maintenance

•

Parts

•

Espahol, p, 39

Sears, Roebuck and Co., Hoffman Estates, IL 60179, U.S.A.

Visit our Sears website: www.sears.com/craftsman

Printed in U.S.A.

FORM NO. 769-00407D

(8/4/2004)

Table of Contents

How do I start my Craftsman 247.770550 yard vacuum?
To start your Craftsman 247.770550 yard vacuum, follow these steps:
1. Attach the spark plug wire and rubber boot to the spark plug.
2. Ensure the bag/chute switch button is fully depressed by the front tab on the bag handle or blower chute.
3. Verify the bag/chute switch wire is connected to the engine and grounded to the mounting bracket.
4. Fill the gas tank to 3/4 full or completely.
5. Move the throttle control lever to the START/RUN (Rabbit) position.
6. Move the choke control toward the throttle control to choke the engine's carburetor. A warm engine may not require choking.
7. While standing behind the unit, grasp the starter handle and pull the rope out until you feel a drag.
8. Pull the rope with a rapid, continuous, full arm stroke. Allow the rope to rewind slowly.
9. Repeat pulling the rope if necessary until the engine starts. Once it starts, gradually move the choke control away from the throttle control. 1
10. If the engine falters, move the choke control back toward the throttle control and repeat steps 7-
1
1. Always keep the throttle control in the START/RUN position when operating the Yard Vacuum.
Was this helpful?
What should I do if my Craftsman 247.770550 yard vacuum won't start?
If your Craftsman 247.770550 yard vacuum won't start, consider the following:
- Fuel Issues: If the fuel tank is empty or contains stale fuel, fill it with clean, fresh gasoline. Note that fuel will not last over thirty days unless a fuel stabilizer is added.
- Spark Plug Connection: If the spark plug wire is disconnected, connect it to the spark plug.
- Recoil Cord Obstruction: If you cannot pull the recoil cord, there might be an obstruction lodged in the impeller. Disconnect the spark plug wire and remove the lodged object.
- Choke Position: Ensure the choke is in the ON position.
- Spark Plug Condition: If the spark plug is faulty, clean, adjust the gap, or replace it.
- Safety Switch: The safety switch must be depressed by the front tab on the bag handle when securing the bag. If the safety switch wire is not connected to the engine or not properly grounded, connect it to the engine connector and ground it to the mounting bracket.
For more information, see page 18 of the manual.
Was this helpful?
How do I clear a jam or clog in my Craftsman 247.770550 yard vacuum?
To clear a jam or clog in your Craftsman 247.770550 yard vacuum, follow these steps:
- General Safety Procedure:
1. Shut the engine off.
2. Wait until all moving parts have come to a complete stop.
3. Disconnect the spark plug wire and ground it against the engine.
  - Never attempt to unclog the feed intake or discharge opening while the engine is running.
- If the discharge area becomes clogged:
1. Stop the engine.
2. Make certain the chipper shredder vacuum has come to a complete stop.
3. Disconnect and ground the spark plug wire to the retaining post.
4. Remove the vacuum bag or blower chute to gain access to the flail screen.
5. Remove the self-tapping screw on the right side of the unit that attaches to the flail screen.
6. Remove the hex screw on top of the rear housing near the mounting bracket and the flange lock nut that secures the flail screen.
7. Remove and clean the screen by scraping or washing with water.
8. Reinstall the screen.
- If a foreign object is lodged in the impeller: After performing the general safety procedure, remove the lodged object.
Was this helpful?
How do I assemble the Craftsman 247.770550 yard vacuum?
To assemble your Craftsman 247.770550 yard vacuum, follow these steps:
1. Disconnect Spark Plug: Before proceeding, disconnect the spark plug wire from the spark plug and ground it onto the retaining post on the engine to prevent accidental starting.
2. Attach the Handle:
  - Remove the hairpin clips, carriage screws, and wing nuts from the lower handle.
  - Place the bottom holes in the lower handle over the pins on the handle brackets and secure with hairpin clips.
  - Insert carriage screws through the upper hole in the lower handle from the inside and secure with wing nuts.
  - Unfold the upper handle until it aligns with the lower handle, ensuring the rope guide is on the right side of the upper handle.
  - Make sure the cables are routed outside the lower handle and are not crimped.
  - Secure the two handles by tightening the handle knobs.
  - Pull the two cable ties attached to the cables tight (approximately 8 inches from each end) and place the cables into the cable guide.
  - Loosen the wing nut that secures the rope guide, pull the starter rope out of the engine slowly and slip it into the rope guide, then tighten the wing nut.
3. Attach the Hose Assembly:
  - Slide the hose adapter of the hose assembly into the base adapter located on the left front of the Yard Vacuum.
  - Pull the spring loaded pin out on the base and align the pin with the first hole (closest to the end of the tube) in the hose adapter, then release the pin to lock the hose in place.
  - Snap the hose handle first into the upper hose handle bracket and then into the lower hose handle bracket.
  - Lay the hose tubing on the hanger bracket next to the chipper chute.
4. Attach the Bag:
  - Grasp the bag handle with one hand and slide the locking rod on the mounting bracket with the other hand toward the engine, using the end of the mounting bracket as leverage.
  - Slip the bag over the rim of the discharge opening and release the locking rod to secure the bag in place.
  - Snap the bag clip to the top of the lower handle.
  - Place the lower straps on the bag over the top of the lower handle, hooking them on the studs.
  - Ensure the bag/chute switch button attached to the mounting bracket is fully depressed by the front tab on the bag handle when securing the bag, or the engine will not start.
5. Attach the Blower Chute (if applicable):
  - The bag must be removed before installing the blower chute.
  - Grasp the blower chute with one hand and slide the locking rod on the mounting bracket with the other hand toward the engine, using the end of the mounting bracket as leverage.
  - Slip the blower chute over the rim of the discharge opening and release the locking rod to secure the chute in place.
  - Raise the nozzle height to the highest setting when using the blower chute.
  - Ensure the bag/chute switch button attached to the mounting bracket is fully depressed by the front tab on the blower chute, or the engine will not start.
Was this helpful?
Why is my Craftsman 247.770550 yard vacuum losing suction?
Your Craftsman 247.770550 yard vacuum may be losing suction due to:
- Loss of power or erratic operation:
  - A loose spark plug wire: Connect and tighten the spark plug wire.
  - The unit running on CHOKE: Move the choke lever to the OFF position.
  - A blocked fuel line or stale fuel: Disconnect the fuel line at the carburetor to drain the fuel tank, then fill with clean, fresh gasoline.
  - Water or dirt in the fuel system: Disconnect the fuel line at the carburetor to drain the fuel tank, then refill with fresh fuel.
  - The carburetor being out of adjustment: Contact your Sears Parts & Repair Center.
  - Low engine RPM: Always run the engine at full throttle.
- Unit does not discharge:
  - A clogged discharge area: Stop the engine, disconnect the spark plug wire, and clean the flail screen and inside of the discharge opening.
  - A foreign object lodged in the impeller: Stop the engine, disconnect the spark plug wire, and remove the lodged object.
  - Low engine RPM: Always run the engine at full throttle.
  - A full vacuum bag: Empty the bag.
For more information, see page 18 of the manual.
Was this helpful?
How do I effectively use the leaf vacuum function on the Craftsman 247.770550?
You can effectively use the leaf vacuum function in two ways:
- Using the Nozzle Vacuum:
1. Place the nozzle/hose vac handle in the top position on the nozzle.
2. Ensure the spring loaded pin is in the first hole (closest to the end of the tube) of the hose adapter.
3. Place both hands on top of the upper handle to push the unit over yard waste.
4. Adjust the nozzle height according to yard conditions. Raise the nozzle for thick layers of leaves or when operating with the blower chute, and lower it for smoother surfaces.
- Using the Hose Assembly:
1. Place the nozzle/hose vac handle in the bottom position on the nozzle to redirect vacuum to the hose assembly.
2. The spring loaded pin must be in the second hole of the hose adapter.
3. Unhook the hose from the upper and lower hose handle brackets and grasp the hose handle to guide it while vacuuming yard waste in hard-to-reach places.
Was this helpful?
How do I clean or empty the collection bag on the Craftsman 247.770550 yard vacuum?
To clean or empty the collection bag:
- To empty the bag:
1. Unhook bag straps from the lower handle and unsnap bag clip from the top of the lower handle.
2. Grasp the bag handle with one hand and pull the lock rod on the mounting bracket with the other hand toward the engine to release.
3. Lift the bag off the back of the unit.
4. Twist the two buttons on the back of the bag to unlock and empty its contents.
5. Hold the bag handle and bag clip while emptying the contents.
- To clean the bag:
  - Wash the bag periodically with water.
  - Allow it to dry thoroughly in the shade.
Was this helpful?
How do I switch between vacuum and blower modes on the Craftsman 247.770550?
To switch between vacuum and blower modes:
- For vacuum mode:
  - To vacuum through the nozzle, place the nozzle/hose vac handle in the top position on the nozzle. The spring loaded pin must be in the first hole of the hose adapter.
  - To vacuum with the hose assembly, place the nozzle/hose vac handle in the bottom position on the nozzle to redirect vacuum to the hose assembly. The spring loaded pin must be in the second hole of the hose adapter.
- For blower mode:
  - Remove the vacuum bag.
  - Attach the blower chute to the unit.
  - Raise the nozzle height to the highest setting when using the blower chute.
  - The bag/chute switch button attached to the mounting bracket must be fully depressed by the front tab on the blower chute for the engine to start.
For more information, see pages 9, 11 and 12 of the manual.
Was this helpful?
What type of fuel does the Craftsman 247.770550 yard vacuum use?

The Craftsman 247.770550 yard vacuum uses clean, fresh, unleaded regular gasoline only. Do not use gasoline containing METHANOL. In general, fuel should be used within 30 days of its purchase date, as gasoline that has been sitting for any period longer than four weeks should be considered stale.

Was this helpful?
Does the Craftsman 247.770550 yard vacuum also mulch leaves?

Yes, the Craftsman 247.770550 yard vacuum is designed to shred material. Yard waste such as leaves and pine needles can be vacuumed up through the nozzle for shredding, and the shredded material is collected in the bag. The material is shredded by the flail blades on the impeller assembly. Do not attempt to shred or chip any material other than vegetation found in a normal yard.

Was this helpful?

Need help?

Do you have a question about the 247.770550 and is the answer not in the manual?

Questions and answers

JOSEPH LECHASSEUR

July 17, 2025

Filling the tank just immediately drains gas. I need to know how to remove the tank and fuel line to check whats wrong and what part numbers are so i can order them online.

1 comments:

Mr. Anderson

September 1, 2025

To remove the fuel tank and fuel line on a Craftsman 247.770550 to check for issues:

1. Stop the engine and disconnect the spark plug wire for safety.
2. Disconnect the fuel line at the carburetor to drain the fuel tank.
3. Inspect the fuel line for blockages, stale fuel, water, or dirt.
4. Refill the tank with clean, fresh gasoline.

If problems persist, further inspection of the carburetor or contacting service may be needed.

This answer is automatically generated

patrick garrity

August 18, 2025

can i order manual for 247 77055

Summary of Contents for Craftsman 247.770550

Page 1 • Operation • Maintenance Safety Rules and • Parts Operating Instructions. • Espahol, p, 39 Sears, Roebuck and Co., Hoffman Estates, IL 60179, U.S.A. Visit our Sears website: www.sears.com/craftsman Printed in U.S.A. FORM NO. 769-00407D (8/4/2004)
Page 2 Maintenance Espa5ol One Year Full Warranty on Craftsman Yard Vacuum This equipment is covered by a one-year warranty, provided that it is maintained, lubricated, and tuned up according to the instructions in the operator's manual. During the warranty year, if this equipment experiences any failure due to defects in material or workmanship, RETURN IT TO YOUR NEAREST SEARS PARTS &...
Page 3 WARNING: This symbol points out important safety instructions which, if not followed, could endanger the personal safety and/or property of yourself and others. Read and follow all instructions in this manual before attempting to operate this machine. Failure to comply with these instructions may result in personal injury.
Page 4 i. Never s tore themachine orfuelcontainer Never operate without either the inlet nozzle or insidewhere thereisanopenflame, s park, optional hose attachment properly attached to the or pilotlight(e.g.furnace, w aterheater, machine. Never attempt to attach or change either spaceheater, c lothes dryer, e tc.) attachment while the engine is running.
Page 5 Once you purchase the Agreement, a simple phone call is all Craftsman® product is designed and manufactured for years of that it takes for you to schedule service. You can call anytime dependable operation. But like all products, it may require repair day or night, or schedule a service appointment online.
Page 6 NOTE: Reference to right and left hand side of the Yard Vacuum is observed from operating Upper position. Safety Glasses This Yard Vacuum has been completely assembled at the factory, except for the handle, bag, and blower Rope chute. These parts are shipped loose in the carton. Guide Upper Hose...
Page 7 ATTACHING THEHANDLE Attaching The HoseAssembly • Remove the hairpin clips from the handle • Slide hose adapter of hose assembly into the base adapter located on the left front of the Yard brackets and remove the carriage screws and wing nuts from the lower handle. See Figure 3A. Vacuum.
Page 8 ATTACHING THEBAG ATTACHING THEBLOWER CHUTE • Grasp bag handle with one hand and slide locking NOTE: The bag must be removed before installing the rod on mounting bracket with other hand toward blower chute. engine. Use the end of mounting bracket as •...
Page 9 Starter Handle Used to grasp bag in order to assist in attaching, Used to start the engine. removing, and emptying bag. Meets ANSI safety standards Craftsman Yard Vacuums conform to the safety standard of the American National Standards Institute (ANSI).
Page 10 HoseAssembly longer than four weeks should be considered stale. Used asanalternative t othenozzle tovacuum yard wastesuchasleaves or pineneedles i n hardto Fill fuel tank with clean, fresh, unleaded regular reach places. gasoline only. Do not use gasoline containing METHANOL. Replace fuel cap. HoseHandle To avoid engine problems, the fuel system should Used toguidehoseassembly w hen vacuuming.
Page 11 • Compress bag opening and fold inner flap over opening. • Fold outer flap over inner flap and insert buttons Throttle Control on the bag through metal outlets. • Twist the buttons to lock bag. Buttons Inner Flap Clip Bag Handle Choke Control Figure 9...
Page 12 • The spring loaded pin must be in the first hole guide the hose while vacuuming yard waste such (closest to the end of the tube) of the hose adapter as leaves or pine needles in hard to reach places. to operate the nozzle vac.
Page 13 Maintenance Schedule Maint. Tasks Every 25 Service Dates hours operation Product: Lubrication Clean Equipment Engine: Check engine oil Change engine oil Service Air Cleaner Service spark plug Service Muffler Clean Engine GENERAL R ECOMMENDATIONS CLEANEQUIPMENT • Always observe safety rules when performing any •...
Page 14 SERVICE SPARK PLUG • Change engine oil after the first five hours of operation, and every twenty-five hours thereafter. • Clean the spark plug and reset the gap to.030" at least once a season or every 50 hours of TODRAINOIL operation.
Page 15 WARNING: Do not attempt to alter the adjustment unit without first engine speed by tampering with the WARNING: Do not at any time make any stopping engine disconnecting engine's governor linkage. Doing so spark plug wire. could result in serious personal injury and damage to the engine.
Page 16 SHARPENING O RREPLACING C HIPPER Remove flange lock nut that secures flail screen to the lower housing. The flail screen does not BLADE have to be removed. Refer to Figure 17. Remove the hex bolt, lock washer, and flat Because the engine on this unit has a tapered washer that secure the impeller assembly to the crankshaft, a special impeller removal tool (part crankshaft.
Page 17 • Do not drain the gas tank and carburetor if using Prepare your Craftsman Yard Vacuum for storage at fuel stabilizer. the end of the season or if the unit will not be used for In all cases, drain all the oil from the crankcase (this 30 days or longer.
Page 18 Problem Possible Cause(s) Corrective Action Engine fails to start Fuel tank empty or stale fuel. Fill tank with clean, fresh gasoline. Fuel will not last over thirty days unless a fuel stabilizer is added. Spark plug wire disconnected. Connect wire to spark plug. Cannot pull recoil cord.
Page 19 Sears Craftsman 6.0 H.P. Yard Vacuum Model 247.770550...
Page 20 Sears Craftsman 6.0 H.P. Yard Vacuum Model 247.770550 Ref. Ref. Part No. Part Description Part Description Part No. 736-0451 Saddle Washer,.320 x.93 710-3025 Hex Cap Screw 5/16-18 x.625 749-04172 Hex Washer Screw 3/8-16 x 1.25 Upper Handle 710-0502A 720-0279 Knob 710-0751 Hex Cap Screw 1/4-20 x.620...
Page 21 Sears Craftsman 6.0 H.P. Yard Vacuum Model 247.770550...
Page 22 Sears Craftsman 6.0 H.P. Yard Vacuum Model 247.770550 Ref. Ref. Part No. Part Description Part Description Part No. 664-0094 Nozzle Door Bag Assembly 731-2294A 681-0154 Screen Assembly 781-04082 Front Wheel Support Brace 710-1054 Hex Screw 5/16-24 x 1.0 781-04081 Rear Wheel Support Brace...
Page 23 Sears Craftsman 6.0 H.P. Engine Model No. 123K02 [ 1058 OWNER'S MANOAL ] 1010 LABEL K,T I 584 _ 5oQ_F 13 _:_ 1099 88@40 :¢_ 34 ;;_ 1095 VALVE GASKET SET 357A 358 ENGINE GASKET KIT 20 @ 15 8 1102 Illustrations cover a range of engines.
Page 24 Sears Craftsman 6.0 H.P. Engine Model No. 123K02 130A 95_617_ 276 @ PRIMER SYSTEM 276 @ CHOKE SYSTEM 121 CARBURETOR OVERHAUL 276@ 977 CARBURETOR GASKET SET 617 0 276 @ 633 @ 104q_ 137_ 633@ 127_ 633A(_ 163_ 617(_ 633A@...
Page 25 Sears Craftsman 6.0 H.P. Engine Model No. 123K02 968B _ 966AI 443A 968A 970 '_ 443_:_ 883J 613A_ 836A 9 836_ 77 _;_ Illustrations cover a range of engines. Parts shown without corresponding text may not be used on your specific engine.
Page 26 Sears Craftsman 6.0 H.P. Engine Model No. 123K02 972_ 957 @ 930C 957A_ _1187AI I _-- __209A_ 209B, 601A 843A 624A 267 _ 267A _26_9 _270 ® 265A _ 265B Illustrations cover a range of engines. Parts shown without corresponding text may not be used on your specific engine.
Page 27 Sears Craftsman 6.0 H.P. Engine Model No. 123K02 564A_ 604A 969A 564 _ 921C 969A 930A 921D 921E 921F 304A 1229 1036 EMISSION LABEL Illustrations cover a range of engines. Parts shown without corresponding text may not be used on your specific engine.
Page 28 Sears Craftsman 6.0 H.P. Engine Model No. 123K02 592 6_ 455A (@ 1211 1210_ 946 (_ 459_ 689¢'_ 597 ,_ 276A 456A 689A _ 1134 101A _73_ Illustrations cover a range of engines. Parts shown without corresponding text may not be used on your specific engine.
Page 29 Sears Craftsman 6.0 H.P. Engine Model No. 123K02 356_ 334 1' 356A__,"'_ 1119 1' 356B_ 3563_6D'D'__ 940'_ 990A 578_ 373 _ 789A 236 _ 74_ i ' __J 922_ 742@ 923A 12o8i' 784_ 78s_ 513@ 783A 8 1236 1009 310 I Illustrations cover a range of engines.
Page 30 Sears Craftsman 6.0 H.P. Engine Model No. 123K02 PART REF. PART PART DESCRIPTION DESCRIPTION DESCRIPTION 691375 Crankshaft 493260 Cylinder Assembly 2678,2679,3120, 399269 Kit-Bushing/Seal 3123,3167,3176. (Used Before Code 493282 Crankshaft (Magneto Side) Date 97011300). *299819 Seal-Oil (Used Before Code Used on Type No(s).
Page 31 Sears Craftsman 6.0 H.P. Engine Model No. 123K02 PART REF. PART PART DESCRIPTION DESCRIPTION DESCRIPTION ,399781 Seal-Oil 499429 499425 Piston Assembly Ring Set (PTO Side) (Standard) (Standard) *691952 Seal-Oil (Used After Code Date (Used After Code Date 97011200). 97011200). (PTO Side)
Page 32 Sears Craftsman 6.0 H.P. Engine Model No. 123K02 REF. PART REF. PART REF. PART DESCRIPTION DESCRIPTION DESCRIPTION 499423 Pin-Piston 691997 497465 Manifold-Intake Slinger-Governor/Oil Note ---- *272199 Gasket-Intake (Standard) 691650 Screw (Used After Code Date 691486 Slinger- Governor/Oil 97011200). (Intake Manifold) Note ---- Used on Type No(s).
Page 33 Sears Craftsman 6.0 H.P. Engine Model No. 123K02 REF. PART REF. PART PART DESCRIPTION DESCRIPTION DESCRIPTION 494870 Jet-Main 498170 Carburetor Float-Carburetor 398187 (Standard) (Primer System) Kit-Needle/Seat e398188 Note ---- (Used After Code Date Gasket-Float Bowl 137 et693981 497466 Jet-Main 95102900).
Page 34 Sears Craftsman 6.0 H.P. Engine Model No. 123K02 REF. PART REF. PART REF. PART DESCRIPTION DESCRIPTION DESCRIPTION 691864 209B 691851 Spring-Governor Spring-Governor 2390,2394,2395, (Light Blue) (Yellow) 2396,2632,2634, Note ---- Used on Type No(s). 2641,2642,2643, 2329, 2349. 691290 Spring- 2644,2645,2646, Note ----...
Page 35 Sears Craftsman 6.0 H.P. Engine Model No. 123K02 PART REF. PART PART DESCRIPTION DESCRIPTION DESCRIPTION 276 et271716 Screw 690354 Spring-Choke Return Washer-Sealing 691108 692031 Bracket-Control (Main Jet) (Blower Housing) 690940 Screw 690450 (Remote/Manual Shield-Cylinder Screw Friction)(Primer) 690345 (Dipstick Tube) 222A...
Page 36 Sears Craftsman 6.0 H.P. Engine Model No. 123K02 REF. PART REF. PART REF. PART DESCRIPTION DESCRIPTION DESCRIPTION 445A 491588 Filter-Air Cleaner 95162 Clamp-Hose 691855 Spring-Friction 691757 Cover-Control Cartridge 690572 Spring-Detent 695161 604A 691344 Cover-Control Screw 691127 Cup-Flywheel 692299 Plate-Pawl Friction...
Page 37 Sears Craftsman 6.0 H.P. Engine Model No. 123K02 PART REF. PART PART DESCRIPTION DESCRIPTION DESCRIPTION 690782 690380 Seat-Valve 691994 Brake Cap-Drive 695267 923A 695891 Brake Cap-End (Exhaust) 262001 690595 (Used After Code Date Bushing-Valve Guide Cover-Linkage 691919 Guard-Rewind 00040600). (Exhaust)
Page 38 Sears Craftsman 6.0 H.P. Engine Model No. 123K02 REF. PART REF. PART REF. PART DESCRIPTION DESCRIPTION DESCRIPTION 691669 Screw 1019 494256 Kit-Label 1059 692311 Kit-Screw/Washer 1036 695111 Emission Label Note ---- (Air Cleaner Primer 696293 Kit-Screw/ Bracket) (Used After Code Date...
Page 39 Por un perfodo de un a_o a partir de la fecha de compra, Sears reparara gratis cualquier defecto en el material o fabricaci6n de esta aspiradora para jardines Craftsman, siempre y cuando haya sido mantenida, lubricada y afinada de acuerdo alas instrucciones de manejo y mantenimiento dadas en el manual del operador.
Page 40 ADVERTENCIA: Este sfmbolo indica instrucciones de seguridad muy importantes las que, si no se siguen, podrian poner en peligro la seguridad personal y/o causar dafios fisicos. Antes intentar manejar esta aspiradora para jardines, se debe leer y seguir todas las instrucciones aparecen en este manual.
Page 41 piedras, pedazos devidrio o demetal) y sean SERVlCIO lanzados porlaboca dedescarga. AIelevar l a boquillaa la posici6nmas alta tambien • Tener sumo cuidado cuando se maneje gasolina y incrementa la admisi6n d e aireparaIograr otros combustibles. Son muy inflamables y sus mejor f uncionamiento delsoplador.
Page 42 NOTE: Para determinar lados derecho izquierdo de la aspiradora para jardines, situarse detras de la maquina, en posicidn de manejarla. Ver Botella de 20 oz. la flgura 1. aceite para motor La aspiradora para jardines fue armada en la fabrica, con la excepci6n del manillar, recolector y tubo de soplado.
Page 43 • Retirar las chavetas de las escuadras del Una a presi6n la manija de la manguera con el soporte de la manija inferior para ajustarla en su manillar y los tornillos de carruaje (cabeza de hongo y cuello cuadrado) y tuercas de mariposa lugar y coloque el caSo de la manguera en el del manillar inferior.
Page 44 • Asireltubodesoplado conunamano y,conlaotra mano, t irardelavarilla defijaci6n enlaescuadra Tolva de demontaje hacia el motor. U seelfinaldesoporte _Soplador demontaje comoelapalancamiento deslizando l a barra quesecierra. V er laFigura 6 . Etiqueta • Deslizar eltubodesoplado pot encimadelborde Delantera delabocadedescarga y soltar l avarilladefijaci6n Cierre de parasujetar e ltuboensulugar.
Page 45 De conformidad con las normas de seguridad de ANSI NOTE: NOTE: Las maquinas aspiradoras para jardines Craftsman cumplen con las normas de seguridad del Instituto de Normalizaci6n Nacional de EE.UU. (ANSI).
Page 46 Llenar hasta la marca FULL, si es necesario. M0ntajede la manguera Volver a colocar la varilla de medici6n y apretarla. Se usa como alternativa del uso del pico para aspirar Revisar el nivel de aceite tres veces antes de los desechos que se acumulan en los patios como arrancar el motor para cerciorarse de que se por ejemplo las hojas o las agujas de los pinos que obtiene una indicaci6n correcta en la varilla.
Page 47 Desconectar elcable delabujfayconectarlo a la estrangulaci6n gradualmente a la posici6n de tierraenelpilarretenedor paraimpedir e l START/run. arranque accidental mientras l amaquina esta 10. Si el motor vacila, mueva la palanca de mando a sol& la posici6n de la ESTRANGULACIOn, entonces de nuevo a la posici6n de START/run.
Page 48 Us0 del m0ntajede la manguera hacia el motor con la otra mano para soltarlo. Consulte Figura 6. • Coloque la manija del pico / manguera de la Saque el canal de soplado del borde de la aspiradora en la posici6n de la base del pico abertura de descarga.
Page 49 PROGRAMA MANTENIMIENTO Lubricaci6n Limpiar el equipo Revisar nivel aceite Campiar aceite motor t¢ Limpiar filtro de aire Limpiar la bujia Limpiar el silenciador Limpiar el motor _,,:._ REC01VlENDACIONES GENERALES LIMPIEZADELEQUIPO • Siempre respetar las reglas de seguridad durante • Limpiar a rondo la aspiradora para jardines los trabajos de mantenimiento.
Page 50 PARA VACIAR ELACEITE SERVlCIO DELA BUJIA Vaciar el aceite mientras el motor est,. caliente. • Limpiar la bujfa y ajustar la distancia entre electrodos a 0.030 pulgada por Io menos una vez Seguir las instrucciones siguientes. en la temporada o cada 50 horas de •...
Page 51 maquina a un centro de servicio Sears para reparacidn y ajuste. ajuste a la maquina sin primero apagar el ADVERTENCIA: Nunca hacer ningdn motor y desconectar el cable de la bujia. velocidad motor moviendo Ajustede la alturadelpico WARNING: intentar alterar varillaje del gobernador del motor.
Page 52 • Retirar el tornillo hexagonal ubicados encima de la carcasa trasera cerca de la escuadra de montaje y la contratuerca que sujeta la rejilla de flagelos. Ver las Figura 1 4. Caja • Retirar y limpiar la rejilla con una rasqueta o lavarla con agua.
Page 53 • Apretar los tornillos de la cuchilla a 210 - 250 pulg-lbs. • Apretar el perno del rotor a 375-425 pulg-lbs. NOTE: Asegurar de instalar la cuchflla astilladora con el fllo hacia arriba. Ver la Figura 19. J_ .... Cuchilla Cuchilla de astilladora flagelos...
Page 54 Problema Soluci6n Causas posibles El motor no arranca El tanque de combustible est,, Llenar el tanque con gasolina limpia y fresca. El combustible no durara mas de treinta dfas vacfo o combustible esta viejo. a menos que se le afiada un estabilizador. El cable de la bujfa esta Conectar el cable de la bujfa.
Page 55 Para Reparaciones Congratulations on making a smart purchase.Your Felicitaciones por haber realizado una adquisici6n Craftsman® product is designed and manufactured for inteligente. El producto Craftsman® que ha adquirido years of dependable operation. But like all products, it esta diseSado y fabricado para brindar muchos aSos de funcionamiento confiable.
Page 56 Your Home For repair-in your home-of all major brand appliances, lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who sold it! For the replacement parts, accessories owner's manuals that you need to do-it-yourself. For Sears professional installation of home appliances...

Craftsman 247.770550 Operator's Manual

Quick Links

Frequently Asked Questions (10)

Need help?

Questions and answers

Related Manuals for Craftsman 247.770550

Summary of Contents for Craftsman 247.770550

Table of Contents