Download
Share
Print this page
Craftsman 917.274951 Owner's Manual
  1. Manuals
  2. Brands
  3. Craftsman Manuals
  4. Lawn Mower
  5. 917.274951
  6. Owner's manual
Craftsman 917.274951 Owner's Manual

Craftsman 917.274951 Owner's Manual

21.0 hp electric start 46" mower 6 speed garden tractor
Hide thumbs

Advertisement

Quick Links

Download this manual
Owner's Manual
JCRRFTSMIIN°I
21.0 HP
ELECTRIC
START
46" MOWER
6 SPEED
GARDEN TRACTOR
Model No.
917.274951
• Safety
• Assembly
• Operation
• Maintenance
• Repair Parts
CAUTION:
Read and follow all Safety
Rules and Instructions before
operating this equipment.
For answers to your questions
about this product,Call:
1-800-659-5917
Sears Craftsman Help Line
5 am - 5 pro, Mon- Sat
SEARS, ROEBUCK AND CO., HOFFMAN ESTATES, IL 60179
Visit our Craftsmanwebsite:www.sears,conYcraftsman

Advertisement

loading
Need help?

Need help?

Do you have a question about the 917.274951 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Craftsman 917.274951

Summary of Contents for Craftsman 917.274951

  • Page 1 For answers to your questions about this product,Call: Read and follow all Safety 1-800-659-5917 Rules and Instructions before Sears Craftsman Help Line operating this equipment. 5 am - 5 pro, Mon- Sat SEARS, ROEBUCK AND CO., HOFFMAN ESTATES, IL 60179 Visit our Craftsmanwebsite:www.sears,conYcraftsman...

  • Page 2: Table Of Contents

    Parts Ordering ..... Back Cover LIMITED TWOYEAR WARRANTY ON CRAFTSMAN RIDING EQUIPMENT PARTS For two (2) years from the date of purchase, if this Craftsman Riding Equipment is maintained, lubricated and tuned up according to the instructions in the owner's manual, Sears will repair or replace, free of charge, any parts found to be defective in material or workmanship.
  • Page 3 IMPORTANT: Th s cutting roach ne s capable of amputating hands and feet and throwing ob ects. Failure to observe the following safety instructions could result in serious injury or death, I. GENERAL OPERATION II. SLOPE OPERATION • Read, understand, and follow al_ Slopes are a major factor related to loss-of- instructionsin the manual and on the controland tipever accidents, which can re-...
  • Page 4 • Never run a machine inside a closed IlLCHILDREN area. Tragic accidents can occur if the operator • Keep nuts and bolts, especially blade is not alert to the presence of children. attachment bolts, tight and keep Children are often attracted to the equipment in good condition.
  • Page 5 • Use slow speed. Choose a low gear so _CAUTION: Tow only the attachments that you will not have to stop or shift that are recommended by and comply while on the slope. with specifications of the manufacturer of • Avoid starting or stopping on a slope. If your tractor.
  • Page 6 PRODUCT SPECIFICATIONS REPAIR AGREEMENT A Repair Agreement is available on this 3ASOLINE 3.5 GALLONS product. Contact your nearest Sears CAPACITY UNLEADED store for details. ANDTYPE: REGULAR CUSTOMER RESPONSIBILITIES DILTYPE SAE 10W30 • Read and observe the safety rules. ',API-SF-SJ): (ABOVE 32°F) •...

  • Page 7: Assembly

    Steering Wheel Steedng Steedng Sleeve Wheel Insert Seat (1) Washer 17/32 x 1-3/16 x 12 Gauge _(1) Knob Mower etainer Springs (2)Flanged (double loop) etainer Spdngs ( 1)Front Plate (single loop) Assembly Gauge Wheels ) Shoulder Bolts 12) Centedock Nuts I Y// "_,,_/(2) Wheels...
  • Page 8 Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness.

  • Page 9: Operation

    INSTALL SEAT TO ROLLTRACTOR OFF SKID (See Operation section for location and Adjust seat before tightening adjustment knob. function of controls) 1. Remove adjustment knob and flat 1. Press lift lever plunger and raise washer securing seat to cardboard attachment lift lever to its highest packing and set aside for assembly of position.
  • Page 10 INSTALL MOWER AND DRIVE BELT 8. Position front plate assembly between front mower brackets• Raise deck and Be sure tractor is on level surface and plate assembly to align holes and mower suspension arms are raised with insert flanged pins. Secure pins with attachment lift control.
  • Page 11 V" CHECKLIST CHECK TIRE PRESSURE The tires on your tractorwere overinflated Before you operate and enjoy your new at the factoryfor shippingpurposes. tractor, we wish to assure that you Correct tire pressure is impodant for best receive the best performance and cutting performance.
  • Page 12 These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning. BATrERY CAUTION REVERSE FORWARD FAST SLOW WARNING ENGINE ON ENGINE OFF OiL PRESSURE LIGHTS ON OVER TEMP LIGHT MOWERLI_ FUEL CHOKE MOWER HEIGHT PARKING...
  • Page 13 KNOWYOURTRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR Compare the illustrationswith your tractor to familiarize yourself with the locations of various controls and adjustments. Save this manual for future reference. Switch Ignition Switch Position Attachment Switch ThrotUe Control Plunger ClutcWBrake...
  • Page 14 The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your tractor or performing any adjustments or repairs. We recommend a wide vision safety mask over spectacles or standard safety glasses.
  • Page 15 The cutting height range is approximately 1. Select desired height of cut. 1-1/2" to 4-1/2". The heights are mea- 2. Lower mower with attachment lift control. sured from the ground to the blade tip with the engine not running. These heights are 3.
  • Page 16 TOWING CARTS A ND OTHER A'FrACH- AWARNING: Experience indicates that MENTS alcohol blended fuels (called gasohol or using ethanol or methanol) can attract Tow only theattachments that a re moisture which leads to separation and recommended byandcomply w ith formation of acids during storage. Acidic specifications ofthemanufacturer ofyour...
  • Page 17 MOWINGTIPS WARM WEATHER STARTING (50 ° F and • Tire chains cannot be used when the above) mower housing is attached to tractor. 7. When engine starts, slowly push • Mower should be properly leveled for choke control in until the engine best mowing performance.

  • Page 18: Maintenance Schedule

    FLLNOATEO MAINTENANCE SCHEDULE COMPLETE REGULAR SERVICE ___,_SERVICE DATES CheCk Brake Operation (I _ Ch_k "13ro pre_ute Check Operator pr_e_'_e* _ntedock Syste*ns Check for LOOSe FaSteners Sharpen/Repla_ _ Mower Blad_ T u,b,_=,o_ c_ V" Check Bakery Level Clean Balten/&rid TermiP, Check Transaxle Co_iP_j A(r_ust Egade Bell(s) Tension l_djust...

  • Page 19: Service And Adjustments

    TRACTOR IMPORTANT: To ensure proper assembly, center hole in blade must align with star Always observe safety r ules when on mandrel assembly. performing any maintenance. 4. Reassemble hex boil, lock washer BRAKE OPERATION and flat washer in exact order as If tractor requires more than six (6) feet shown.
  • Page 20 BA'n'ERY ENGINE LUBRICATION Your tractor has a battery charging system which is sufficient for normal use. How- Only use high quality detergent oil rated ever, periodic charging of the battery with with API service classification SF-SJ, an automotive charger will extend its life. Select the oil's SAE viscosity grade •...
  • Page 21 Oil Drain Valve NOTE: Do not wash the paper cartridge or use pressurized air, as this will damage the cartridge. 6. Remove nut and cartridge plate. 7. Reinstall the pre-cleaner (cleaned and oiled) over the paper cartridge. 8. Check rubber seal for damage and proper position around stud.
  • Page 22 CLEANING We do not recommend using a garden hose to clean your tractor unless the • Clean engine, battery, seat, finish, etc. electrical system, muffler, air filter and of all foreign matter. carburetor are covered to keep water out. • Keep finished surfaces and wheels free Water in engine can result in a shortened of all gasoline, oil, etc.
  • Page 23 SIDE-TO-SIDE ADJUSTMENT • Recheck side-to-side adjustment. • Raise mower to its highest position. • Measure height from bottom edge of mower to ground level at front corners of mower. Distance "A" on both sides of mower should be the same. •...
  • Page 24 Left Hand Mower Center _Screws Electric Mandrel Blade Mandrel i_eaftnd_LeftHand Idler ClutChpulley Mandrel Man_rel_ Mandrel Mower Cover _ Drive Cove Idler Arm Mower Sway Bar Drive Bracket Belt Belt TO ADJUST A'I-rACHMENT CLUTCH Keepers The electdc clutch should provide years of service, The clutch has a built-in brake TO REPLACE MOWER BLADE that stops the pulley within 5 seconds,...
  • Page 25 IMPORTANT: Check Brake Adjustment 4. Road test tractor for proper stopping distance as stated above. Readjust if Clutching Flat Idler, necessary. If stopping distance is still greater than six (6) feet in highest gear, Engine Above further maintenance is necessary. Contact a Sears or other qualified service center.
  • Page 26 If "jumper cables" are used for emergency starting, follow this procedure: IMPORTANT: Your tractor is equipped with a 12 volt negative grounded system. The other vehical must also be a 12 volt negative grounded system. Do not use your tractor battery to start other vehicles. TO ATTACH JUMPER CABLES - 1.
  • Page 27 7. Connect BLACK grounding cable to Adjustment Bolt Spring negative (-) battery terminal with remaining hex bolt and keps nut. Tighten securely Close terminal access doors. Close hood. Hex Bolt Keps Terminal Access._, S Attachment Lift Jam Nut Spring Door TO REMOVE ROOD AND GRILL Positive ASSEMBLY...
  • Page 28 Idle Fuel IMPORTANT: Damage to the needles Adjusting and the seats in carburetor may result if Screw screw is turned in too tight. PRELIMINARY SETI'ING - Control Cable 1. Be sure you have a clean air filter, and the throttle control cable is adjusted properly (see "TO ADJUST THROTTLE CONTROL CABLE"...

  • Page 29: Storage

    expedance indicates that alcohol Immediately prepare your tractor for blended fuels (called gasohol or using storage at the end of the season or if the tractor will not be used for 30 days or ethanol or methanol) can attract moisture more.

  • Page 30: Troubleshooting

    TROUBLESHOOTING CHART CORRECTION =ROBLEM CAUSE 1. Fill fuel tank. Will not start 1. Out of fuel, 2. See"TO START ENGINE" 2. Engine not "CHOKED" in Operation section, properly. 3. Wait several minutes 3. Engine flooded. before attempting to start. 4. Bad spark plug. 4.
  • Page 31 TROUBLESHOOTING CHART PROBLEM CAUSE CORRECTION Loss of power 1. Cutting too much grass/too 1. Set in "Higher Cut" position/ fast, reduce speed. 2. Throttle in "CHOKE" 2. Adjust throttle control. position. I 3. Clean underside of mower 3. Build-up of grass, leaves and trash under mower, housing.
  • Page 32 TROUBLESHOOTING CHART PROBLEM CAUSE CORRECTION _1owerbladesw[ll 1. Obstruction in clutch 1. Remove obstruction. rot rotate mechanism. 2. Worn/damaged mower 2. Replace mower drive belt. drive belt. 3. Frozen idler pulley. 3. Replace idler pulley. 4. Frozen blade mandrel. 4. Replace blade mandrel. 1.
  • Page 33 TRACTOR -- MODEL NUMBER 917.274951 SCHEMATIC BATTERy SOLENO4D FUSE STARTER ', _ ELECTRIC CLUTCH • PTO (DISENGAGED) PRESENCE L ..SEAT SWITCH (NOT C_,CUPIE D) METER SPARK FI.UG S e--- ,GN,_,O_ "_ UNIT • ON T,NIN CYL ENGINES FUEL SHUT_)FF SOLENOID IGNITION SWITCH...
  • Page 34 TRACTOR - - MODEL NUMBER 917.274951 ELECTRICAL...
  • Page 35 TRACTOR -- MODEL NUMBER 917.274951 ELECTRICAL PART DESCRIPTION 144,927 Battery 74760412 Bolt Hex Head 1/4-20 x 3/4 7603J Tray, Battery 145211 Bolt 1/4-20 x 7,5 Zinc 150109 Hold down Battery Dash Mount 145769 Nut Push Nylon 1/4" 153664 Switch Interlock Push-In 166184 Harness Socket Light W/4152J 4152J...
  • Page 36 TRACTOR - - MODEL NUMBER 917.274951 CHASSIS AND ENCLOSURES...
  • Page 37 TRACTOR -- MODEL NUMBER 917.274951 CHASSIS AND ENCLOSURES PART PART DESCRIPTION DESCRIPTION 175465 Rail, Frame RH 175476 Bracket, Chassis Front 175282 D_wb_,G1 154614 Asm., S_sp Ch_s_'_ Lh 73680700 Nut, Crownlock Hex 7/16-14UNC 175315 B_cket Asm., Fender 163976X428 Dash YTGT 2 Cyl 17G60620 Screw 3/8-16 x 1-1/4 157882...
  • Page 38 TRACTOR - - MODEL NUMBER 917.274951 GROUND DRIVE...
  • Page 39 TRACTOR -- MODEL NUMBER 917.274951 GROUND DRIVE KEY PART KEY PART NO. NO. DESCRIPTION DESCRIPTION 9858M1' Key, Woodruff 121749X Washer 25/32 x1-1/4 x 16 Ga. 7563R WaSher, Thrust, Axle 150035 Ny_ner 174g_o06 Screw Thdro_5/16-18 x 3/4 74321016 Screw, Fin. #10-24 x 1 STD5414.T/ Nut, Crownlock 3/8-16 178575...
  • Page 40 TRACTOR - - MODEL NUMBER 917.274951 STEERING ASSEMBLY...
  • Page 41 TRACTOR -- MODEL NUMBER 917.274951 STEERINGASSEMBLY PART DESCRIPTION 139768 Wheel, Steering 178557 Axle Asm., Front 6855 Fitting, Grease 161849 Spindle Asm, LH 161848 Spindle Asm., RH 62_6H Bearing, Race Thrust Harden 121748X Washer 25/32 x 1-5/8 x 16 Ga. 1'2(J(_029 Ring, Klip #T5304-75 121232X Cap, Spindle...
  • Page 42 TRACTOR -- MODEL NUMBER 917.274951 ENGINE SPARK ARRESTER PART PART DESCRIPTION DESCRIPTION ..Engine (See Breakdown) 10010500 Washer Split Kohler Model No. CV624-65577 123487X ClampHose 149723 Muffler 17490636 Screw TT 3/8-16 x 2-1/4 UNC 121361X PuTleyV-Idler 17490664 Screw TT 3/8-16 x 4 UNC 177748 Keeper Asm.
  • Page 43 TRACTOR o* MODEL NUMBER 917.274951 SEAT ASSEMBLY _,_,_ PART PART DESCRIPTION DESCRIPTION 140123 Seat 134300 Spacer, Split 140551 Bracket, Pivot Seat 121250X Spring, Cprsn 140675 123976X Nut. LOCk 1/4 Lge Fkj Gr. 5 Strap, Fender 127018X 18171912 Washer 17/32x 1-3,'16x 12 Ga. Bolt, Shoulder 5/16-18 x .62 Knob, Seat 166369...
  • Page 44 DESCRIPllON 177423 Decal, Dash Panel 160397 Decal, V-Belt Schematic 164_85 Decal, Dash 177539 Decal, Rapl Parts 1717(_ Decal, Hood, Craftsman, RH 178993 Decal, Engine 171703 Decal, Hood, Craftsman, LH 177628 Decal, Engine KHLR Fan 149516 Decal, Battery DNGPJPSN 138047 Decal, Battery...
  • Page 45 TRACTOR - - MODEL NUMBER 917.274951 LIFT ASSEMBLY 35 73 PART PART DESCRIPTION DESCRIPTION 1210C6X Rod Asm., Lever 150233 Trunnion, InfinHeight 177535 Shaft Asm., Lift Vgt 110807X Nut, Special 159189 Lever Asm., Litt Rh 19131016 Washer 13/32 x 5/8 x 16 Ga. 12OOOO22 E-RingTruarc#5133-87 137150...
  • Page 46 TRACTOR - - MODEL NUMBER 917.274951 MOWERDECK 16 117...
  • Page 47 TRACTOR -- MODEL NUMBER 917.274951 MOWERDECK PART PART DESCRIPTION DESCRIPTION 156948 Deck Weldment 144945 Anchor, Spring Deck 46" 138457 Bracket Asm., Sway Bar 17490628 Screw, 3/8-16 x 1-3/4 STD624008 Retainer Spdng STD5510_7 Washer 13132 x13/16 x 16 Ga. 130632 Arm, Suspenslan, Rear (Sway 131494 Pullay, Idtar, F_at 1560_...
  • Page 48 TRACTOR - - MODEL NUMBER 917.274951 TRANSAXLE...
  • Page 49 TRACTOR -- MODEL NUMBER 917.274951 TRANSAXLE PART PART DESCRtP'nON DESCRIWRON 4197R Axle Shaft 8119M Needle Beanng 1'2_XX_34 Retaining Ring 4220R Thrust Beating Race 4199R Final Drive Gear 4209R 3rd Reduction pinion. Low Differential Gear 4213,=1 4th Reductlen Gear 4216R 4215R Differential Pinion 4442R 3rd Reduction Pinion Spacer...
  • Page 50 TRACTOR - ° MODEL NUMBER 917.274951 KOHLER ENGINE-MODEL NUMBERCV624, TYPE NUMBER65577 CYLINDER HEAD, VALVE BREATHER _m13 t5... ° i[_/'' O_10...
  • Page 51 TRACTOR- - MODEL N UMBER 9 17.274951 KOHLER ENGINE-MODEL NUMBER CV624, TYPE NUMBER 65577 HEADNALVE/BREATHER CRANKCASE KEY PART KEY PART DESCRIPTION DESCRIPTION 24-033-01-S Kit, breather cover w/gasket 24-032-01-S Seal, oil front (Includes 2, 3, 5) Crankcase (USE: Miniblock 24-O41-23-S Gasket, breather 24 782 24) 24-096-59-S...
  • Page 52 TRACTOR -- MODEL NUMBER 917.274951 KOHLER ENGINE-MODEL NUMBER CV624,TYPE NUMBER 65577 IGNITIONIELECTRICAL BLOWER HOUSING BAFFLES e.-1 °_- t _,-o d!---s 3--*" AIR INTAKE...
  • Page 53 TRACTOR - - MODEL NUMBER 917.274951 KOHLER ENGINE-MODELNUMBER CV624, TYPE NUMBER65577 IGNITION/CHARGING BLOWER HOUSING & BAFFLES KEY PART KEY PART DESCRIPTION NO. NO. DESCRIPTION Housing, blower 54-755-15-S Kit, grass screen 24-027-20-S (Incl. 2-4) _nciudes 2-4,and 24 113 18- 24-100-01-S Nut plasflc (3) M-403025-S Screw, hox.
  • Page 54 TRACTOR -- MODEL NUMBER 917.274951 KOHLER ENGINE-MODEL NUMBER CV624,TYPE NUMBER 65577 STARTING SYSTEM OIL PAN / LUBRICATION .-_ L,[ z";...
  • Page 55 TRACTOR -- MODEL NUMBER 917.274951 KOHLER ENGINE-MOBEL NUMBER CV624,TYPE NUMBER 65577 OIL PAN/LU BRICATION STAR_NGSYSTEM PART PART DESCRIPTION DESCRIPTION 24-199-07-S Pan, oil assembly M-839080-S Screw, hex. flange (Includes 2-10) Mex1.25xe0 M-645025-S Screw, hex. flange 25-098-08-S Starter, solenoid shift MExl.0:'25 _lndudes 4-7) M-631005-S Washer...
  • Page 56 TRACTOR -- MODEL NUMBER 917.274951 KOHLER ENGINE-MODEL NUMBER CV624, TYPE NUMBER 65577 CRANKSHAFT EXHAUST FUELSYSTEM...
  • Page 57 TRACTOR -- MODEL NUMBER 917.274951 KOHLER ENGINE-MODELNUMBERCV624, TYPE NUMBER 65577 FUEL SYSTEM CRANKSHAFT PART PART DESCRIPTION DESCRIPTION 24-014-72-S C_nksha_(Includes 24-853-25oS Kit, carburetor w/gaskets 52-139-09-S Plug, cup (Includes 2-4) 24o041-15-S Gasket, carburetor 24-053-25 Carburetor assembly For information only not ava abe separate y EXHAUST (Includes 24 757 18-S,...
  • Page 59 SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION ONLY RIDE UP AND DOWN HILL, NOT ACROSS HILL SIGHTING _. CU GUIDE T/./_.- S greater than 15 ), never across the face. Make turns gradu- ally to prevent tipping or loss of control. Exercise extreme Operate...
  • Page 60 For repairof major brand appliancesin your own home... no matter who made it, no matter who sold 1-800-4-MY-HOME Any_me, day_ night (1-800_ (U.S.A. andCanada •www_e_i*_com W_w.seell,ca For repairof carry-in products like vacuums,lawn equipment, a nd electrenics, caJl f orthe nearestSearsParts and Repair Center, 1-800-486-1222 Any_rne, day crr_l__.SA orgy)