Table of Contents
Advertisement
Owner's Manual
CRRFTSMRN °
LAWN TRACTOR
16.0 HP, 42" Mower
Electric Start
6 Speed Transaxle
Model No.
917.274350
_]]]
his product
has a low emission engine which operates
differently from previously
built engines. Before you start the
engine, read and understand this Owner's Manual.
IMPORTANT:
Read and follow all Safety
Rules and Instructions before
operating this equipment.
For answers to your questions about
this product, Call:
1-800-659-5917
Sears Craftsman Help Line
5 am - 5 pm, Mon - Sat
Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.
Visit our Craftsman
website:www.sears.com/craftsman
Advertisement
Table of Contents
Related Manuals for Craftsman 917.274350
Summary of Contents for Craftsman 917.274350
- Page 1 Read and follow all Safety this product, Call: Rules and Instructions before 1-800-659-5917 Sears Craftsman Help Line operating this equipment. 5 am - 5 pm, Mon - Sat Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A. Visit our Craftsman...
- Page 2 Maintenance......... 17 Warranty..........2 SafetyRules ........... 3 Service andAdjustments...... 2 2 ProductSpecifications......6 Storage..........27 Assembly/Pre-Operation ......8 Troubleshooting ........28 Operation..........11 Repair Parts.......... 32 MaintenanceSchedule......1 7 Sears Service......B ack Cover LIMITEDWARRANTYON CRAFTSMANRIDINGEQUIPMENT Fortwo (2) years from the date of purchase,if this CraftsmanRiding Equipmentis maintained,lubricatedand tuned up accordingto the instructionsin the owner'smanual, Searswill repair or replacefree of charge any parts that are foundto be defectivein materialor workmanshipaccordingto the guidelinesof coveragelisted below.Searswill...
- Page 3 IMPORTANT: This cutting machine is capable of amputating hands and feet and throw- ing objects. Failure to observe the following safety instructions could result in serious injury or death. • Never direct discharged material toward _I, WARNING: In order to prevent ac- anyone.
- Page 4 II. SLOPE OPERATION • Never carry children, even with the blades shut off. They may fall off and Slopes are a major factor related to loss of be seriously injured or interfere with control and tip-over accidents, which can safe machine operation.
- Page 5 • Keep machine free of grass, leaves, • Removegas-poweredequipmentfrom the truck or trailerand refuel it on the other debris build-up. Clean oil or fuel spillage and remove any fuel-soaked ground. If this is not possible,then debris. Allow machine to cool before refuel such equipmentwith a portable storing.
- Page 6 (Gap: .030") AGREEMENTS Ground Speed Forward: Congratulations on making a smart pur- (MPH): chase. Your new Craftsman® product is designed and manufactured for years of dependable operation. But like all products, it may require repair from time to time. That's...
- Page 7 Steering Wheel Steering (1) Large Flat Washer Wheel Insert © (1) 5/16 Lock Washer (1) Hex Bolt 5/16-18 x 4 Steering Extension Steering Wheel Adapter Steering Shaft Boot Seat (1) Washer 17/32 x1-3/16 x12 Gauge ) Knob (1) Oil Drain Tube For Future Use Slope Sheet...
- Page 8 Your new tractor has been assembled at the factory with the exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure...
- Page 9 7. Slide seat until a comfortableposition NOTE: You may now roll or drive your is reachedwhich allowsyou to press tractor off the skid. Follow the appropriate clutch/brakepedal all the way down. instruction below to remove the tractor 8. Get off seat withoutmoving its ad- from the skid.
- Page 10 CHECK TIRE PRESSURE #" CHECKLIST The tires on your tractor were overin- Before you operate and enjoy your new flated at the factory for shipping purposes. tractor, we wish to assure that you receive Correct tire pressure is important for best the best performance and satisfaction cutting...
- Page 11 These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning. I'.,I SLOW REVERSE NEUTRAL HIGH CHOKE FAST IGNITION SWITCH ENGINE OFF REVERSE ENGINE ON ENGINE START PARKING BRAKE PARKING BRAKE PARKING BRAKE OPERATION LOCKED...
- Page 12 KNOW YOUR TRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations various controls and adjustments. Save this manual for future reference. ROS "ON" Position Attachment Ignition Switch Clutch Lever Light Switch...
- Page 13 The operation of any tractor result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your tractor or performing adjustments or repairs. We recommend a wide vision safety mask over spectacles...
- Page 14 USING THE REVERSE OPERATION • The average lawn should be cut to ap- SYSTEM proximately 2-1/2 inches during the cool season and to over 3 inches during 1. Depress clutch/brake pedal all the way months. For healthier and better looking down and hold.
- Page 15 TOWING CARTS OTHER ATTACH- CAUTION: Alcohol blended fuels (called MENTS gasohol or using ethanol or methanol) attract moisture which leads to separa- Tow only the attachments that are recom- tion and formation of acids during storage. mended by and comply with specifications Acidic gas can damage the fuel system...
- Page 16 6. When engine starts, leave throttle control in choke position until engine warms up and begins to run roughly. Once rough running begins, imme- diately move the throttle control to the fast position. Engine warm-up take from several seconds to several minutes (the colder the temperature,...
- Page 17 MAINTENANCE SCHEDULE _____ FILL IN DATES /_/@_/_-_,_" /_'_ _.Oq'_ " AS YOU COMPLETE BE OLAR SERV,CE OATES Check Operator Presence ROS Systems Check for Loose Fasteners II_s Sharpen/Replace Mower Blades Lubrication Chart Check Battery Level Clean Battery and Terminals Check Transaxle Cooling Check V-Belts Check Engine...
- Page 18 TRACTOR CHECK REVERSE OPERATION (ROS) SYSTEM Alwaysobserve safety ruleswhen per- forming any maintenance. • When the engine is running with the ig- BRAKE OPERATION nition switch in the engine "ON" position and the attachment clutch is engaged, If tractor requiresmore than five (5) feetto any attempt by the operator to go into...
- Page 19 V-BELTS • The blade can be sharpened with a file or on a grinding wheel. Do not attempt Check V-belts for deterioration and wear to sharpen while on the mower. after 100 hours of operation and replace • To check blade balance, you will need a if necessary.
- Page 20 Unlock drain valve by pushing inward NOTE: If very dirty or damaged, replace slightly and turning counterclockwise. cartridge. To open, pull out on the drain valve. Place new pre-cleaner and cartridge After oil has drained completely, close firmly in base. and lock the drain valve by pushing Align tabs on cover with slots in blower inward...
- Page 21 CLEANING With engine cool, remove filter and plug fuel line sections. • Clean engine, battery, seat, finish, etc. Place new fuel filter in position in fuel of all foreign matter. line with arrow pointing towards carbu- • Keep finished surfaces and wheels free retor.
- Page 22 FRONT-TO-BACK ADJUSTMENT Raise lift lever to raise suspension arms. Slide mower out from under trac- IMPORTANT: Deck must be level side-to tor. side. If the following front-to-back adjust- IMPORTANT: If an attachment other than ment is necessary, be sure to adjust both the mower deck is to be mounted...
- Page 23 TO REPLACE MOWER BLADE DRIVE Measure distance between brake oper- BELT ating arm and nut "A" on brake rod. If distance is other than 1-1/2", loosen The mower blade drive belt may be re- jam nut and turn nut "A" until distance placed without tools.
- Page 24 FRONT WHEEL TOE-IN/CAMBER Make sure belt is in all pulley grooves and inside all belt guides and keepers. The front wheel toe-in and camber are not Install mower (See "TO INSTALL adjustable on your tractor. If damage MOWER" in this section of manual).
- Page 25 2. Connectone end of the BLACKcable Terminal Cover Keps to the NEGATIVE(-) terminal (C) of fully charged battery. 3. Connectthe other end of the BLACK "-_. Bolt cable (D) to good chassisground, awayfrom fuel tank and battery. Positive TO REMOVECABLES, REVERSE (Red) ORDER- Cable...
- Page 26 ENGINE IMPORTANT: Damage to the needle valve and the seat in carburetor may result Maintenance, repair, or replacement of the if screw is turned in too tight. emission control devices and systems, which are being done at the customers expense, PRELIMINARY SETTING may be performed...
- Page 27 Immediatelyprepareyour tractor for stor- blended fuels (called gasohol or using ageat the end of the season or if the trac- ethanol or methanol) can attract moisture tor will not be used for 30 days or more. which leads to separation and formation _WARNING: Neverstore the tractor...
- Page 28 TROUBLESHOOTING CHART: See appropriate section in manual unless directed to Sears service center PROBLEM CAUSE CORRECTION Will not start 1. Out of fuel. Fill fuel tank. See "TO START ENGINE" Engine not "CHOKED" properly. in Operation section. Wait several minutes Engine flooded.
- Page 29 TROUBLESHOOTING CHART: See appropriate section in manual unless directed to Sears service center PROBLEM CAUSE CORRECTION Loss of power Cutting too much grass/too Raise cutting height/reduce fast. speed. Throttle in "CHOKE" position. Adjust throttle control. Clean underside of mower Build-up of grass, leaves and trash under...
- Page 30 TROUBLESHOOTING CHART: See appropriate section in manual unless directed to Sears service center PROBLEM CAUSE CORRECTION Mower blades will 1. Remove obstruction. 1. Obstruction in clutch not rotate mechanism. Worn/damaged mower drive Replace mower drive belt. belt. Frozen idler pulley. Replace idler pulley.
- Page 31 TRACTOR - - MODEL NUMBER 917.274350 SCHEMATIC BATTERY SOLENOID STARTER BLACK GRAY IGNITION _PARGKPLUG_ UNIT (2 PLUGS ON TWIN CYL. ENGINES) BLUE ¢q HOUR BLACK METER FUEL I (OPTIONAL) I1__1 c LINE II BLUE CHARGING SYSTEM OUTPUT 28 VOLTS AC MIN. @ 3600 RPM 3 AMP DC @ 3600 RPM (CHARGING SYSTEM...
- Page 32 TRACTOR - - MODEL NUMBER 917.274350 ELECTRICAL...
- Page 33 Nut, Keps Hex 1/4-20 unc 4207J Cable Ground 6 Ga. 12" black 192749 Switch Seat 193350 Switch Ign 140403 Key Ign Molded Craftsman 110712X Switch Light 193374 Harness Ign 71110408 Bolt BIk. Fin Hex 1/4-20 unc x 1/2 131563 Cover Terminal Red...
- Page 34 TRACTOR - - MODEL NUMBER 917.274350 CHASSIS AND ENCLOSURES 212__ chassis-Laser -It.stlt_38...
- Page 35 TRACTOR - - MODEL NUMBER 917.274350 CHASSIS AND ENCLOSURES PART DESCRIPTION 174619 Chassis Stamping 176554 Drawbar 155272 Bumper Hood/Dash 193510X012 Dash STD533710 Bolt, Carriage 3/8-16 x 1 174996 Panel, Dash, L.H. 172105X010 Panel, Dash, R.H. 17490608 Screw Thdrol 3/8-16 x 1/2 185682X613 Hood Assembly Laser 184921...
- Page 36 TRACTOR - - MODEL NUMBER 917.274350 GROUND DRIVE \ \- /202 . 51 drive-fender, stlt...
- Page 37 TRACTOR - - MODEL NUMBER 917.274350 GROUND DRIVE PART PART DESCRIPTION DESCRIPTION Transaxle Peerless 206-545C 175410 Pulley, Engine 173937 Bolt Hex 7/16-20 x 4 x Gr. 5 (See Breakdown) 10040700 Washer Lock 146682 Spring Brake Return 154778 123666X Pulley Transaxle Keeper Belt Engine Hydro 142432 Screw Hex Wsh Hi-Lo 1/4 x 1/2 unc...
- Page 38 TRACTOR - - MODEL NUMBER 917.274350 STEERING ASSEMBLY -_----*_ ..¢ _ _\ 43 steering_plJt...
- Page 39 TRACTOR - - MODEL NUMBER 917.274350 STEERING ASSEMBLY PART DESCRIPTION 186780 Steering Wheel 175131 Axle Assembly 169840 Spindle Assembly, L.H. 169839 Spindle Assembly, R.H. 6266H Bearing, Race, Thrust, Hardened 121748X Washer 25/32 x 1-5/8 x 16 Ga. 19272016 Washer 27/32 x 1-1/4 x 16 Ga. 12000029 Ring, Klip 3366R...
- Page 40 TRACTOR - - MODEL NUMBER 917.274350 ENGINE OPTIONAL EQUIPMENT Spark Arrester engine-bs.lcyl...
- Page 41 TRACTOR - - MODEL NUMBER 917.274350 ENGINE PART DESCRIPTION 170545 Control, Throttle/Choke 17720408 Screw, Hex Head, Thread Cutting 1/4-20 x 1/2 Engine, Briggs Model No. 283H07-0399-E1 (See Breakdown) 137352 Muffler 165291 Gasket 148456 Tube Drain Oil Easy 169837 Shield Brn/Dbr Guard 137180 Arrestor, Spark 187750...
- Page 42 TRACTOR - - MODEL NUMBER 917.274350 SEAT ASSEMBLY seat It.knob PART PART DESCRIPTION DESCRIPTION 188716 Seat 121248X Bushing, Snap 180166 Bracket, Pivot, Seat 72050412 Bolt, Carriage 1/4-20 x 1-1/2 71110616 Bolt 134300 Spacer, Split .28 x .88 19131610 Washer 13/32 x 1 x 10 Ga. 121250X Spring 145006...
- Page 43 133644 Decal, Customer Maintenance Decal, Lift Handle 193545 179768X428 Decal, Hood Side Pad, Footrest LH 179769X428 163204 Decal, Fender Craftsman Pad, Footrest RH 156439 193496 Decal, Fender Danger Owner's Manual, English 193497 179128 Decal, Deck "B" 42" Owner's Manual, Spanish...
- Page 44 TRACTOR - - MODEL NUMBER 917.274350 LIFT ASSEMBLY 1718 32 /...
- Page 45 TRACTOR - - MODEL NUMBER 917.274350 LIFT ASSEMBLY PART DESCRIPTION 159460 Lift Lever Inner Wire Assembly 159471 Shaft Assembly, Lift 105767X Pin, Groove 12000002 E-Ring 19211621 Washer 21/32 x 1 x 21 Ga. 120183X Bearing, Nylon 125631X Grip, Handle, Fluted 122365X Button, Plunger, Red 139865...
- Page 46 TRACTOR - - MODEL NUMBER 917.274350 MOWER DECK .146 1" 42 deck rnamt-path...
- Page 47 TRACTOR - - MODEL NUMBER 917.274350 MOWER DECK PART PART DESCRIPTION DESCRIPTION Bolt Carr. Sh. 3/8-16 x 1-1/2 Gr. 5 165892 Mower Deck Assembly, 42" 72110612 STD533107 Bolt 131494 Pulley, Idler, Flat 138017 Bracket Assembly, Sway Bar, Front 73900600 Nut Lock Fig. 3/8-16 uric 165460 Bracket Sway Bar 38/42"...
- Page 48 TRACTOR - - MODEL NUMBER 917.274350 PEERLESS TRANSAXLE - - MODEL NUMBER 206-545C 180"'_ 3,5A 151) MODEL and SERIAL NUMBERS HERE...
- Page 49 TRACTOR - - MODEL NUMBER 917.274350 PEERLESS TRANSAXLE - - MODEL NUMBER 206-545C PART PART DESCRIPTION DESCRIPTION 772147 Transaxle Cover 790079 Brake Lever Screw 1/4 - 20 x 1-1/4" 780086A Needle Bearing 5/8" 792073A 770128 Transaxle Case 792085A Screw 1/4 - 20 x 2 1/4" Locknut 5/16 - 24 776395...
- Page 50 TRACTOR - - MODEL NUMBER 917.274350 BRIGGS ENGINE-MODEL NUMBER 283H07, TYPE NUMBER 0399-E1 146 _ 358 ENGINE GASKET 868_) 943 O 20 @ 6170 1022 681@ 524_ 8420 11019 LABEL KIT] [1058 OWNER S MANUAL ! 3_6 _Bil 11329 REPLACEMENT ENGINE] 1095 VALVE GASKET 617 O...
- Page 51 TRACTOR - - MODEL NUMBER 917.274350 BRIGGS ENGINE-MODEL NUMBER 283H07, TYPE NUMBER 0399-E1 1267 729 _ 9o6'_ 305A 186C_ 697 '_ 127 0 74 ) 1070 276@ 947@ 9504_ 1005 1" 1266 0 801 @ 803_ 310 1...
- Page 52 TRACTOR - - MODEL NUMBER 917.274350 BRIGGS ENGINE-MODEL NUMBER 283H07, TYPE NUMBER 0399-E1 PART PART DESCRIPTION DESCRIPTION 697132 Cylinder Assembly 690464 Valve-Choke (Manual Choke) 399265 Kit-Bushing/Seal (Magneto Side) 108A 692344 Valve-Choke (Choke A Matic) 391086 • Seal-Oil (Magneto Side) 694352 (D Jet-Main (Standard) 697106 Sump-Engine...
- Page 53 TRACTOR - - MODEL NUMBER 917.274350 BRIGGS ENGINE-MODEL NUMBER 283H07, TYPE NUMBER 0399-E1 PART PART DESCRIPTION DESCRIPTION • + Seal-Valve 491055 Plug-Spark 690968 Wire-Connector/Alternator 697151 Gasket Set-Engine 393456 19203 Flywheel Puller 690960 Screw (Rocker Cover) Solenoid-Fuel 89838 Wrench-Spark Plug 694393 691691 Washer (Governor Crank) 691657...
- Page 55 SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION ONLY RIDE UP AND DOWN HILL, NOT ACROSS HILL 15 DEGREES MAX. down the face of slopes, never across the face. Do not mow ARNING: To avoid serious injury, operate your tractor up and slopes greater than 15 degrees.
- Page 56 Your Home For repair = in your home = of ati major brand appliances, iiiiiiiiiiiiiiiiii ¸¸¸ lawn and garden equipment, or heating and cooling systems, iiiiiiiiiiiili iiiiiiiiiiiiiiiiiii no matter made it, no matter somd it! iiiiiiiiiiiiiiiiiii iiiiiiiiiiiiiiiiiii For the replacement parts, accessories iiiiiiiiiiiiiiiiiii iiiiiiiiiiiiiiiiiii...