Download  Print this page

CRAFTSMAN 18383 Operator's Manual

Heavy duty tool chests.
Hide thumbs
   

Advertisement

OPERATOR'S
MANUAL
HEAVY
DUTY TOOL CHESTS
Periodically the drawer fronts, drawer trim, and other surfaces
should be cleaned with a mitd detergent and water.
Auto wax witt preserve the unit's luster finish. Apply the wax
as to a car. The wax witt atso hetp protect the unit against
scratches.
Grease and oit can be removed with most standard
cleaning fluids. For safety, use a nonflammable cleaning fluid.
- If drawer liners are supplied, it is recommended
they are used
to protect the finish inside the drawers and to make the drawers
easier to clean. The drawer liners may be cleaned
with soap and water.
MODEL 18383 / 18391
MODEL 18392 / 18393
CALL 1o800o366o7278 FOR SERVICE PARTS. Refer to Service
Parts Drawing for futt listing of Service Parts.
LOCATING
MODEL # INFORMATION
Model numbers and other information required for service parts is
located on a label on the interior right side of the top most drawer.
The maximum weight for each drawer should be no more than
85 tbs.
The maximum product weight for both models, including con-
tents, should be no more than 1,000 tbs.
For casters, use high quality bearing grease, (yearly).
Lubricate the slides with grease or equivatent,(twice
yearly.)
Lubricate tock with graphite, (yearly).
Distributed
by Sears Brands Management Corporation,
Hoffman Estates, IL 60179
DANGER
_
is used to indicate a hazardous situation which,
if not avoided, wit__Ji
result in serious injury or death.
WARNING
z_
indicates a hazardous situation which,
if not avoided, could result in serious injury or death.
CAUTION is used to indicate a hazardous situation which, if not
avoided, _
result in minor injury, moderate injury, or property
damage.
CAUTION:
Read and follow all Safety Rules and Operating
instructions before first use of this product.
DANGER
,_
DO NOT stand on this product. You may fatt or cause product
to tip.
DO NOT open more than one drawer. The product may be-
come unstable and tip.
DO NOT step in the drawers. You may fatt or cause product to
tip.
DO NOT mount this product on a truck bed or any other mov-
ing object.
DO NOT move the product prior to closing and locking att the
drawers and chest tid. The drawers could come open and
make the product unstable and tip.
DO NOT place any objects on top of chest tid. Remove att
objects from chest tid before opening.
WARNING
A
* WEAR SAFETY GLASSES when removing or repositioning
the slides.
- DO NOT pull the unit, push it when moving
- USE THE BRAKES when not moving this product. This wiii
prevent the product from roiling.
- DO NOT alter this product in any manner. For example, do not
weld external tockbars or attach electrical equipment.
- Keep the product on level surfaces. The product may become
unstable and tip if stored or moved on an uneven surface.
- BE CAREFUL when closing the cover. Remove hands before
the cover closes completely.
CAUTION
- This product is not designed to be directly lifted with a fork lift,
or to be towed with any mechanical devices.
- The maximum weight for each drawer should never be
exceeded.
- Only transport this product empty. Properly secure when
transporting.
- DO NOT exceed maximum product weight, including contents.
See Capacities for more information.
F1931

Advertisement

   Summary of Contents for CRAFTSMAN 18383

  • Page 1

    OPERATOR'S MANUAL Periodically the drawer fronts, drawer trim, and other surfaces should be cleaned with a mitd detergent and water. Auto wax witt preserve the unit's luster finish. Apply the wax HEAVY DUTY TOOL CHESTS as to a car. The wax witt atso hetp protect the unit against scratches.

  • Page 2

    NOTE: Not a JJ a ssembly instructions will r elate toyour m odel TOOLS REQUIRED: 3/8-in W rench SIDE HANDLE ATTACHMENT 1/2-in W rench items Needed: Cross4ip Screwdriver #14 - 10 x 3/4 Cross-tip Screw (Qty: 4) Cross-tip Screwdriver Process: - Attach the side handle using (4) #14 - 10 x 3/4 Cross-tip HARDWARE INCLUDED:...

  • Page 3

    GAS SPRINGS INSTALLATION LABELS (iF APPLICABLE) items Needed: PrOCeSS: Gas Springs (Qty: 2) Appty a tight film of glass cleaner to the surface where 5/16 - 18 Ball Studs (Qty: 4) the tabel is to be applied. 5/16 - 18 Clip-on Nut (Qty: 4) Peel the label from the backing and place the tabet in 1!2-in Wrench position.

  • Page 4

    _± INSTALLING DRAWERS Ball bearing slide = Putt slides and slide carrier out to fully extended position (see illustration.) Hold the slide on the cabinet while aligning it with the slide on drawer. Slightly insert one side and repeat for the other side. Slowly push drawer to its fully closed position to engage slide.

  • Page 5

    MANUAL DE USUARIO • Lubrique la cerradura con grafito (anualmente). • Limpie con detergente suave y agua los frontales y los bordes laterales de los cajones y las demSs superficies. CAJAS DE HERRAMIENTAS DE TRABAJO PESADO • La cera para autom6viles preservar8 el acabado brilloso de la unidad.

  • Page 6

    NOTA: No todas las instrucciones de ensambtaje se HERRAMIENTAS NECESARIAS: refieren a tu modelo. Llave Ingtesa de 3/8 inch Llave Inglesa de 1/2 inch INSTALACION DE LA MANIJA LATERAL Destomittador de Punta en Cruz Elementos necesarios: Tomillos Phillips de No. 14 - 10 x 3/4 (Cant.: 4) Destomittador de Punta en Cruz PIEZAS INCLUIDAS:...

  • Page 7

    INSTALACI6N DEPRIMAVERAS DEGAS ETJQUETAS (SJ APUCA) Elementos necesarios: Proceso: Amortiguador neum_ticoes (Cant: 2) - Aptica una capa fina de Jimpiador para vidrios en ta Pemo Esf6rico de 5/16 - 18 (Cant: 4) superficie donde se colocar_ ta etiqueta. Tuerca de Abrazadera de 5/16 - 18 (Cant: 4) - Quite el revestimiento de ta etiqueta y coJOquela en su Uave Allen de 1/4 pig sitio.

  • Page 8

    INSTALACION DEGAVETAS Correderas derodamientos esf6ricos - hale hacia afuera tas correderas y et soporte de las correderas hasta que queden en posici6n totatmente extendida (ver itus- traciOn). Sostenga ta corredera en et gabinete mientras to atinea con ta corredera de ta gaveta. Soporte de las correderas Corredera INSTALACION...

This manual also for:

183911839218393

Comments to this Manuals

Symbols: 0
Latest comments: