Craftsman Tool Storage Roll-Away Operating Instructions

f
Tool Storage
Roll-Away
THIS OPERATING INSTRUCTION MANUAL
COVERS ALL THE PROFESSIONAL SERIES
ROLL-AWAYS.
PROFESSIONAL SERIES
Please indicate the following information
from the service part drawing provided.
Model
Number:
Model
Description:
CAUTION: Read and follow all Safety
Rules and Operating Instructions before
first use of this product. Retain this
document for future reference.
Sears, Roebuck and Co.
Hoffman Estates, IL 60179 U.S.A.
F 1374A1
f -,,
Call 1-800-366-7278 for
Service Parts
Refer to Service Parts Drawing for full
_.._ listing of Service Parts
SAFETY RULES AND WARNINGS"
• DO NOT stand on this product. You may fall which may cause personal injury.
• WEAR SAFETY GLASSES AND GLOVES when cutting the banding material. The
bands may snap which may cause personal injury.
• Stacked products should be bolted together. The products could become unstable and
tip, which may cause personal injury or product damage.
• WEAR SAFETY GLASSES when removing or repositioning the slides. The tool could
slip which may cause personal injury.
• When moving this product, do not pull it. Push the product to prevent personal injury.
• Handle and swivel casters must be attached on the same side of the product.
• USE THE BRAKES when not moving this product. This will prevent the product from
rolling, which may cause personal injury or product damage.
• BE CAREFUL when opening more than one drawer. The product may become unstable
and tip, which may cause personal injury or product damage.
• DO NOT mount this product on a truck bed or any other moving object. This may cause
personal injury or product damage.
• DO NOT step in the drawers. You may fall which may cause personal injury.
• Appropriately secure this product before moving it with a forklift.
• DO NOT tow with power equipment. The product could tip, which may cause personal
injury or product damage.
• DO NOT alter this product in any manner. For example, do not weld external tockbars or
attach electrical equipment. This may cause product damage or personal injury.
• A heavy duty side cabinet must be used on an equally heavy duty roll-away.
• Keep the product on level surfaces. The product may become unstable and tip if stored
or moved on an un-level surface, which may cause personal injury or product damage.
• Lock the drawers and doors before moving this product. The drawers or doors could
come open and make the product unstable and tip, which may cause personal injury or
product damage.
• The maximum weight for each drawer should be no more than 50 pounds.
• The maximum product weight, including contents, cannot exceed 1,180 pounds.
f
DRAWER REMOVAL:
• Fully extend the drawer. Push it back a quarter of an inch.
• Insert a screwdriver into the slot in the slide and push
in on the stop until it clears the lance. Repeat the procedure
on the other slide and remove the drawer.
• To reinstall, pry the stop far enough out to engage the
lance and push the drawer onto the slides until the stops
pass over the lances.
Slot .z Stop
Lance
LUBRICATION: Lubricate the top and bottom channels
of the drawer slides at least twice a year.
HANDLE INSTALLATION: (dependant on model)
• Insert the handle tabs into the slots in the end of the roll-away.
• Attach the handle using four 1/4-20 x 3/8 slotted round head screws.
• Insert one plug in each end of the side handle.
LOCKING THE UNIT:
If the unit has no panel, the tock activates the locking mechanism.
• To unlock, turn the key to the right and the unit is unlocked.
• To lock, make sure all drawers are fully closed, turn the key, then remove the key.
If the unit has a panel, the panel activates the locking mechanism.
• To unlock the unit, turn the key to the right and the panel automatically springs open at
the bottom. Pull out, lift up and push the panel back into the unit.
• To lock, pull panel straight out, then lower, press lightly at the bottom and turn the key
CASTER INSTALLATION:
• Lay the roll-away on its back. Use packaging material to protect the finish.
• Mount both swivel casters on the same side of the unit as the side handle.
• Attach the casters using four 14-10 x 5/8 screws on each caster.
• Wrench tighten all screws. It is recommended not to exceed 80 inch pounds of torque.
• Return the unit to its upright position.