Craftsman HEAVY DUTY TOOL CHESTS Operator's Manual
Craftsman HEAVY DUTY TOOL CHESTS Operator's Manual

Craftsman HEAVY DUTY TOOL CHESTS Operator's Manual

Heavy duty tool chests

Advertisement

Available languages

Available languages

OPERATOR'S
MANUAL
T
®
HEAVY DUTY TOOL CHESTS
• Periodically the drawer fronts, drawer trim, and other surfaces
should be cleaned with a mild detergent and water.
• Auto wax will preserve the unit's luster finish. Apply the wax
as to a car. The wax will also help protect the unit against
scratches.
• Grease and oil can be removed with most standard
cleaning fluids. For safety, use a nonflammable cleaning fluid.
• If drawer liners are supplied, it is recommended
they are used
to protect the finish inside the drawers and to make the drawers
easier to clean. The drawer liners may be cleaned
with soap and water.
DANGER
A_,
is used to indicate a hazardous situation which,
if not avoided, wil___J
result in serious injury or death.
WARNING
Z_
indicates a hazardous situation which,
if not avoided, could result in serious injury or death.
CAUTION is used to indicate a hazardous situation which, if not
avoided, _
result in minor injury, moderate injury, or property
damage.
CAUTION:
Read and follow all Safety Rules and Operating
Instructions before first use of this product.
* Product you purchased may vary from picture shown
CALL 1-800-366-7278
FOR SERVICE PARTS. Refer to Service
Parts Drawing for full listing of Service Parts.
LOCATING
MODEL # iNFORMATiON
Model numbers and other information required for service parts is
located on a label on the interior right side of the top most drawer.
• The maximum weight for each drawer should be no more than
75 Ibs.
• The maximum product weight for both models, including
contents, should be no more than 650 Ibs.
• For casters, use high quality bearing grease, (yearly).
• Lubricate the slides with grease or equivalent,(twice
yearly.)
• Lubricate lock with graphite, (yearly).
Distributed
by Sears Brands Management Corporation,
Hoffman Estates, IL 60179
DANGER
_,
• DO NOT s;cand on this product. You may fall or cause product
to tip.
• DO NOT open more than one drawer. The product may be-
come unstable and tip.
• DO NOT step in the drawers. You may fall or cause product to
tip.
• DO NOT mount this product on a truck bed or any other mov-
ing object.
• DO NOT move the product prior to closing and locking all the
drawers and chest lid. The drawers could come open and
make the product unstable and tip.
• DO NOT place any objects on top of chest lid. Remove all
objects from chest lid before opening.
WARNING
Z_
• WEAR SAFETY GLASSES when removing or repositioning
the slides.
• DO NOT pull the unit, push it when moving
• USE THE BRAKES
when not moving this product. This will
prevent the product from rolling.
• DO NOT alter this product in any manner. For example, do not
weld external Iockbars or attach electrical equipment.
• Keep the product on level surfaces. The product may become
unstable and tip if stored or moved on an uneven surface.
• BE CAREFUL when closing the cover. Remove hands before
the cover closes completely.
CAUTION
• This product is not designed to be directly lifted with a fork lift,
or to be towed with any mechanical devices.
• The maximum weight for each drawer should never be
exceeded.
• Only transport this product empty. Properly secure when
transporting.
• DO NOT exceed maximum product weight, including contents.
See Capacities for more information.
F1913

Advertisement

Table of Contents
loading

Summary of Contents for Craftsman HEAVY DUTY TOOL CHESTS

  • Page 1 OPERATOR'S MANUAL ® • Periodically the drawer fronts, drawer trim, and other surfaces HEAVY DUTY TOOL CHESTS should be cleaned with a mild detergent and water. • Auto wax will preserve the unit's luster finish. Apply the wax as to a car. The wax will also help protect the unit against scratches.
  • Page 2 CASTER INSTALLATION (26-iNCH CABINET) TOOLS REQUIRED: items Needed: #14 - 10 x 5/8dn Hex Screws (Qty: 16) 3!8dn Wrench 3!8dn Wrench 7/16dn Wrench Cross4ip Screwdriver Process: NOTE: Use adequate personne_ for this operation. NOTE: Failure to instal_ easter angles may result in premature cabinet failure.
  • Page 3 iNSTALLiNG DRAWERS LABELS (iF APPLICABLE) BaH bearing s_ide - Putt slides and slide carrier out to fully PrOCeSS: extended position (see illustration.) Hold the slide on the Apply a light film of glass cleaner to the surface where cabinet while aligning it with the slide on drawer. Slightly the label is to be applied.
  • Page 5 MANUAL DE USUARIO ° • Lubrique la cerradura con grafito (anualmente). CAJAS DE HERRAMIENTAS DE TRABAJO PESADO • Limpie con detergente suave y agua los frontales y los bordes laterales de los cajones y las demSs superficies. La cera para autom6viles preservar8 el acabado brilloso de la unidad.
  • Page 6 JNSTALACION DEL TIRADOR (26 PULG. GABJNETE) HERRAMIENTAS NECESARIAS: Elementos necesarios: Tornitto Hexagonal de No. 14 - 10 x 5/8 (Cant.: 16) Llave Ingtesa de 3/8 inch Ltave Allen de 3/8 ptg Llave Inglesa de 7/16 inch Destomittador de Punta en Cruz NOTA: UtiHce personal adecuado para esta operaci6n.
  • Page 7 INSTALACION DE GAVETAS ETIQUETAS (Sl APLICA) Correderas de rodamientos esfericos -jate hacia afuera PrOCeSO: tas correderas yet soporte de tas correderas hasta que - Aptica una capa fina de limpiador para vidnos en ta queden en posiciOn totatmente extendida (vet itustraciOn). superficie donde se colocar_ la etiqueta.

Table of Contents